Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SCT2230ATVAR

SCT · DC-DC Converters · SOT-563

SCT2230ATVAR from SCT, in a SOT-563. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Power supply input (4.2V-17V). Supplies power to the IC and the step-down converter switches. Bypass VIN to GND with a suitably large ceramic capacitor (≥0.1uF local, additional 10uF bulk if supply is more than a few inches away).
2 SW power_out Power switching output (switching node). Connect the output LC filter from SW to the output load. A capacitor (0.1uF or greater ceramic) is required from SW to BST to power the high-side switch. Absolute max -1V to 20V (-2.5V to 22V for <10ns pulses).
3 GND power_in Power ground. Must be soldered directly to the ground plane.
4 BST power_in Bootstrap power supply for the high-side power MOSFET gate driver. Must connect a 0.1uF or greater ceramic capacitor between BST and SW.
5 EN input Enable logic input. Floating the pin enables the device via an internal 1.5uA pull-up. Precision enable thresholds 1.18V rising / 1.1V falling with 5.5uA hysteresis current allow programmable UVLO threshold and hysteresis via an external divider from VIN.
6 FB input Buck converter output feedback sensing voltage. Connect a resistor divider from VOUT to FB to set the output voltage. Internal reference is 0.8V typical (0.792-0.808V at 25°C).

Key specifications

Parameter Value
Manufacturer SCT
Package SOT-563
Category PMIC
Pins 6

Ordering variants

Same part, different packaging or reel option.

  • SCT2230ATVAR

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN input voltage (absolute maximum) VIN -0.3 20 V 2
VSW switch node voltage (absolute maximum) VSW -1 20 V 2
VSW switch node voltage, pulse (absolute maximum) VSW -2.5 22 V <10ns 2
Bootstrap voltage VBST (absolute maximum) VBST -0.3 6 V Relative to VSW; printed as VSW-0.3 to VSW+6 2
FB voltage (absolute maximum) VFB -0.3 6.5 V 2
EN voltage (absolute maximum) VEN -0.3 6.5 V 2
Junction temperature (absolute maximum) TJ -40 150 °C Over operating free-air temperature 2
Storage temperature TSTG -65 150 °C 2
Input voltage range (recommended) VIN 4.2 17 V 3
Operating junction temperature (recommended) TJ -40 125 °C 3
Operating input voltage VIN 4.2 17 V 4
Input UVLO, VIN rising VIN_UVLO 4 4.15 V VIN rising 4
Shutdown current ISD 1.5 5 uA EN=0, No load, VIN=12V 4
Enable high threshold VEN_H 1.18 1.25 V 4
Enable low threshold VEN_L 1.03 1.1 V 4
Enable pin input current IEN 1 1.5 2 uA EN=1V 4
Feedback voltage, TJ=25°C VFB 0.792 0.8 0.808 V TJ=25°C, CCM 4
Feedback voltage, TJ=-40°C~125°C VFB 0.784 0.8 0.816 V TJ=-40°C~125°C, CCM 4
LSD valley current limit ILIM_LSD 3.2 3.7 4.2 A 4
Quiescent current IQ 155 uA EN=2V, No load, No switching. VIN=12V. BST-SW=5V 4
Hysteresis (VIN UVLO) 300 mV 4
Enable pin hysteresis current IEN_HYS 5.5 uA EN=1.5V 4
High side FET on-resistance RDSON_H 70 mΩ 4
Low side FET on-resistance RDSON_L 42 mΩ 4
Switching frequency FSW 750 kHz VIN=12V, VOUT=5V 4
Minimum on-time tON_MIN 90 ns 4
Minimum off-time tOFF_MIN 220 ns 4
Internal soft-start time tSS 2.5 ms 4
Thermal shutdown threshold TSD 160 °C TJ rising 4
Thermal shutdown hysteresis 20 °C 4
Junction to ambient thermal resistance (SOT563) RθJA 120 °C/W 3
Junction to case thermal resistance (SOT563) RθJC 8 °C/W 3

CAD (KiCad official)

  • Symbol: SCT2230ATVAR
  • Footprint: Package_TO_SOT_SMD:SOT-563
  • 3D model: SOT-563 (KiCad packages3D, STEP)
  • 3D model files: sct2230atvar-etched.step / sct2230atvar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sct2230atvar.step / sct2230atvar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SCT datasheet (15 pp, sha256 7846808e5cb7c7db, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF