3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLP8864SQRHBRQ1
Texas Instruments · LED Drivers · VQFN-32(5x5)
LP8864SQRHBRQ1 from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LED_GND | power_in | LED ground connection. |
| 2 | LED_GND | power_in | LED ground connection. |
| 3 | OUT4 | passive | LED current sink output; tie to ground if unused, and the recommended range for OUT1 to OUT4 is 0 to 48 V. |
| 4 | LED_GND | power_in | LED ground connection. |
| 5 | OUT3 | passive | LED current sink output; tie to ground if unused, and the recommended range for OUT1 to OUT4 is 0 to 48 V. |
| 6 | OUT2 | passive | LED current sink output; tie to ground if unused, and the recommended range for OUT1 to OUT4 is 0 to 48 V. |
| 7 | OUT1 | passive | LED current sink output; tie to ground if unused, and the recommended range for OUT1 to OUT4 is 0 to 48 V. |
| 8 | INT | output | Device fault interrupt output, open drain; a 10-kΩ pullup resistor is recommended. |
| 9 | SDA | bidirectional | SDA for I2C interface; a 10-kΩ pullup resistor is recommended, and the absolute maximum on this pin is VDD + 0.3 V. |
| 10 | SCL | bidirectional | SCL for I2C interface; a 10-kΩ pullup resistor is recommended, and the absolute maximum on this pin is VDD + 0.3 V. |
| 11 | BST_SYNC | input | Input for synchronizing boost; connect to ground to disable spread spectrum or to VDD to enable it when synchronization is not used. |
| 12 | PWM | input | PWM input for brightness control; tie to GND if unused. |
| 13 | SGND | power_in | Signal ground. |
| 14 | LED_SET | passive | LED string configuration through external resistor; do not leave floating. |
| 15 | PWM_FSET | passive | LED dimming frequency setup through external resistor; do not leave floating. |
| 16 | BST_FSET | passive | Boost switching frequency setup through external resistor; do not leave floating. |
| 17 | MODE | passive | Dimming mode setup through external resistor; do not leave floating. |
| 18 | UVLO | passive | Input voltage sense for programming the input UVLO threshold through an external resistor to VIN. |
| 19 | VSENSE_P | passive | Input voltage detection for OVP protection and positive input for input current sense; recommended range is 3 to 48 V. |
| 20 | VSENSE_N | passive | Negative input for input current sense; tie to VSENSE_P if input current sense is not used. |
| 21 | SD | output | Power line FET control, open-drain output; leave floating if unused. |
| 22 | VDD | power_in | Power supply input for internal analog and digital circuits; connect a 10-µF capacitor to GND, with recommended range 3 to 5.5 V. |
| 23 | EN | input | Enable input. |
| 24 | C1N | passive | Negative input for charge pump flying capacitor; leave floating if the feature is not used. |
| 25 | C1P | passive | Positive input for charge pump flying capacitor; leave floating if the feature is not used. |
| 26 | CPUMP | power_out | Charge pump output; connect to VDD if the charge pump is not used, and a 4.7-µF decoupling capacitor is recommended. |
| 27 | GD | output | Gate driver output for external N-FET. |
| 28 | PGND | power_in | Power ground. |
| 29 | ISNS | passive | Boost current sense pin; recommended range is 0 to 5.5 V. |
| 30 | ISNSGND | power_in | Current sense resistor GND. |
| 31 | ISET | passive | LED full-scale current setup through external resistor. |
| 32 | FB | passive | Boost feedback input; recommended range is 0 to 48 V. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32(5x5) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 33 |
CAD (KiCad official)
- Symbol:
LP8864SQRHBRQ1 - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
lp8864sqrhbrq1-etched.step/lp8864sqrhbrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp8864sqrhbrq1.step/lp8864sqrhbrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (88 pp, sha256
58ec6541568213fa, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).