Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM3406HVQMHXQ1

Texas Instruments · LED Drivers · TSSOP-14

LM3406HVQMHXQ1 from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Switch pin, connected to the output inductor and Schottky diode.
2 SW output Switch pin, connected to the output inductor and Schottky diode.
3 BOOT passive MOSFET drive bootstrap pin; connect a 22 nF ceramic capacitor from this pin to the SW pins.
4 NC unconnected No internal connection; leave this pin unconnected.
5 VOUT input Output voltage sense pin; connect to the output node where the inductor and the first LED's anode connect.
6 CS input Current sense feedback pin; set the LED current by connecting a resistor from this pin to ground.
7 GND power_in Ground pin; connect to system ground.
8 DIM input Input for PWM dimming; logic high enables output and logic low disables output, reducing average LED light output.
9 COMP passive Error amplifier output; connect a 0.1 µF ceramic capacitor with X5R or X7R dielectric from this pin to ground.
10 RON input On-time control pin; a resistor connected from this pin to VIN sets the regulator controlled on-time.
11 VCC power_out Output of the internal 7V linear regulator; bypass to ground with a minimum 0.1 µF ceramic capacitor with X5R or X7R dielectric.
12 VINS input Input voltage PWM dimming comparator input; connect to the anode of the input diode to allow dimming by PWM of the input voltage.
13 VIN power_in Input voltage pin; nominal operating input range is 6V to 75V for LM3406HV and LM3406HV-Q1.
14 VIN power_in Input voltage pin; nominal operating input range is 6V to 75V for LM3406HV and LM3406HV-Q1.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSSOP-14
Category LED Drivers
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to GND VIN -0.3 76 V LM3406HV, LM3406HV-Q1 3
VINS to GND VINS -0.3 76 V LM3406HV, LM3406HV-Q1 3
VOUT to GND VOUT -0.3 76 V LM3406HV, LM3406HV-Q1 3
BOOT to GND BOOT -0.3 76 V LM3406HV, LM3406HV-Q1 3
SW to GND SW -1.5 76 V LM3406HV, LM3406HV-Q1 3
BOOT to VCC BOOT-VCC -0.3 76 V LM3406HV, LM3406HV-Q1 3
BOOT to SW BOOT-SW -0.3 14 V 3
VCC to GND VCC -0.3 14 V 3
DIM to GND DIM -0.3 7 V 3
COMP to GND COMP -0.3 7 V 3
CS to GND CS -0.3 7 V 3
RON to GND RON -0.3 7 V 3
Junction Temperature TJ 150 °C 3
Storage Temp. Range TSTG -65 125 °C 3
ESD Rating ESD 2 kV Human body model 3
Lead Temperature (Soldering, 10sec) 260 °C Soldering, 10 sec 3
Infrared/Convection Reflow (15sec) 235 °C 15 sec 3
VIN input voltage range VIN 6 75 V LM3406HV, LM3406HV-Q1 3
Junction Temperature Range (LM3406HV-Q1) TJ -40 150 °C LM3406HV-Q1 3
Ambient Temperature Range (LM3406HV-Q1) TA -40 125 °C LM3406HV-Q1 3
Thermal Resistance θJA (TSSOP-14 Package) θJA 50 °C/W TSSOP-14 Package; DAP soldered to 2 sq in 1-oz copper 3
CS Regulation Threshold VREF 187.5 200 210 mV CS Decreasing, SW turns on 4
CS Regulation Threshold (over temperature) VREF 191 210 mV CS Decreasing, SW turns on; junction temperature 0°C-125°C (footnote 2) 4
CS Over-voltage Threshold V0V 300 mV CS Increasing, SW turns off 4
CS Bias Current ICS 0.9 µA CS = 0V 4
VOUT Bias Current IVOUT 83 µA VOUT = 24V 4
COMP Pin Current ICOMP 25 µA CS = 0V 4
Error Amplifier Transconductance Gm-CS 145 µS 150 mV < CS < 250 mV 4
Shutdown Threshold (LM3406HV-Q1) VSD-TH 0.3 0.7 1.066 V RON Increasing 4
Shutdown Hysteresis VSD-HYS 40 mV RON Decreasing 4
Minimum Off-time tOFF-MIN 230 ns CS = 0V 4
Programmed On-time (LM3406HV-Q1) tON 800 1300 1850 ns VIN = 24V, VO = 12V, RON = 200kΩ 4
Minimum On-time tON-MIN 280 ns 4
VINS Pin Threshold VINS-TH 70 %VIN VINS decreasing 4
VINS Pin Input Current IIN-2WD 25 µA VINS = 24V * 0.7 4
VCC Regulated Output (LM3406HV-Q1) VCC-REG 6.4 7 7.5 V 0 mA < ICC < 5 mA 4
VCC Bypass Threshold VCC-BP-TH 8.8 V VIN Increasing 4
VCC Current Limit VCC-LIM 4 20 mA VIN = 24V, VCC = 0V 4
VCC Under-voltage Lock-out Threshold VCC-UV-TH 5.3 V VCC Increasing 4
VCC Under-voltage Lock-out Hysteresis VCC-UV-HYS 150 mV VCC Decreasing 4
IIN Operating Current IIN-OP 1.2 mA Non-switching, CS = 0.5V 4
IIN Shutdown Current IIN-SD 240 350 µA RON = 0V 4
Current Limit Threshold (LM3406HV-Q1) ILIM 1.65 2.1 2.6 A 4
Logic High VIH 2.2 V DIM Increasing 4
Logic Low VIL 0.8 V DIM Decreasing 4
DIM Pull-up Current IDIM-PU 80 µA DIM = 1.5V 4
Buck Switch On Resistance RDS-ON 0.37 0.75 Ω ISW = 200 mA, BOOT = 6.3V 4
BOOT Under-voltage Lock-out Threshold VDR-UVLO 1.7 2.9 4.3 V BOOT-SW Increasing 4
BOOT Under-voltage Lock-out Hysteresis VDR-HYS 370 mV BOOT-SW Decreasing 4
Thermal Shutdown Threshold TSD 165 °C 4
Thermal Shutdown Hysteresis TSD-HYS 25 °C 4
Junction to Ambient θJA θJA 50 °C/W TSSOP-14 Package 5

CAD (KiCad official)

  • Symbol: LM3406HVQMHXQ1
  • Footprint: Package_SO:TSSOP-14_4.4x5mm_P0.65mm
  • 3D model: TSSOP-14 (KiCad packages3D, STEP)
  • 3D model files: lm3406hvqmhxq1-etched.step / lm3406hvqmhxq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm3406hvqmhxq1.step / lm3406hvqmhxq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (42 pp, sha256 701e308df9f549cb, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF