LTC2862HS8-1#PBF from Analog Devices, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	RO	output	Receiver output: high when A-B > 200mV and low when A-B < -200mV with RE low, high if inputs are open, shorted or terminated without signal, and high-impedance when RE is high.
2	RE	input	Receiver enable: a low input enables the receiver, a high input forces RO high-impedance, and RE high with DE low enters low power shutdown.
3	DE	input	Driver enable: a high input enables the driver, a low input forces the driver outputs high-impedance, and DE low with RE high enters low power shutdown.
4	DI	input	Driver input: with DE high, a low on DI forces A (noninverting output) low and B high, and a high on DI forces A high and B low.
5	GND	power_in	Ground.
6	A	bidirectional	Noninverting receiver input and noninverting driver output, with impedance > 96kΩ in receive mode or unpowered and ±60V fault protection.
7	B	bidirectional	Inverting receiver input and inverting driver output, with impedance > 96kΩ in receive mode or unpowered and ±60V fault protection.
8	VCC	power_in	Power supply, 3V < VCC < 5.5V, bypass with 0.1µF ceramic capacitor to GND.

Key specifications

Parameter	Value
Manufacturer	Analog Devices
Package	SO-8
Category	Communication Interface Chip/UART/485/232
Pins	8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Primary Power Supply	VCC	3		5.5	V		4
Supply Current in Shutdown Mode (H-Grade)	ICCS		0	40	µA	DE = 0V, RE = VCC	4
Supply Current, Driver and Receiver Enabled	ICCTR		900	1300	µA	No Load, DE = VCC, RE = 0V	4
Differential Driver Output Voltage	/VOD/	1.5			V	R = ∞ (Figure 1)	5
Differential Driver Output Voltage	/VOD/	1.5		5	V	R = 27Ω (Figure 1)	5
Differential Driver Output Voltage	/VOD/	2			V	R = 50Ω (Figure 1)	5
Change in Magnitude of Driver Differential Output Voltage	Δ/VOD/			0.2	V	R = 27Ω or 50Ω (Figure 1)	5
Driver Common-Mode Output Voltage	VOC			3	V	R = 27Ω or 50Ω (Figure 1)	5
Change in Magnitude of Driver Common-Mode Output Voltage	Δ/VOC/			0.2	V	R = 27Ω or 50Ω (Figure 1)	5
Maximum Driver Short-Circuit Current	IOSD		150	250	mA	-60V ≤ (Y or Z) ≤ 60V (Figure 2)	5
Driver Three-State Output Current	IOZD	-30		30	µA	DE = 0V, VCC = 0V or 3.3V, VO = -25V, 25V	5
Receiver Input Current (A,B)	IIN			143	µA	VCC = 0V or 3.3V, VIN = 12V (Figure 3)	5
Receiver Input Current (A,B)	IIN	-100			µA	VCC = 0V or 3.3V, VIN = -7V (Figure 3)	5
Receiver Input Resistance	RIN		112		kΩ	0 ≤ VCC ≤ 5.5V, VIN = -25V or 25V (Figure 3)	5
Receiver Common Mode Input Voltage	VCM	-25		25	V	(A + B)/2	5
Differential Input Signal Threshold Voltage	VTH	-200		200	mV	-25V ≤ VCM ≤ 25V	5
Differential Input Signal Hysteresis	ΔVTH		150		mV	VCM = 0V	5
Differential Input Failsafe Threshold Voltage		-200	-50	0	mV	-25V ≤ VCM ≤ 25V	5
Differential Input Failsafe Hysteresis			25		mV	VCM = 0V	5
Receiver Output Low Voltage	VOL			0.4	V	I(RO) = 3mA (Sinking)	5
Receiver Three-State Output Current on RO	IOZR	-5		5	µA	RE = High, RO = 0V or VCC	5
Receiver Short-Circuit Current	IOSR	-20		20	mA	RE = Low, RO = 0V or VCC	5
Logic Input Current (DE, DI, RE)	IINL	-5	0	5	µA	0 ≤ VIN ≤ VCC	5
Maximum Data Rate	fMAX	20			Mbps	Driver high speed (Note 3)	6
Driver Input to Output	tPLHD, tPHLD		25	50	ns	RDIFF = 54Ω, CL = 100pF (Figure 4)	6
Driver Input to Output Difference	ΔtPD		2	9	ns	RDIFF = 54Ω, CL = 100pF (Figure 4)	6
Driver Output Y to Output Z Skew	tSKEWD	-10		10	ns	RDIFF = 54Ω, CL = 100pF (Figure 4)	6
Driver Rise or Fall Time	tRD, tFD		4	15	ns	RDIFF = 54Ω, CL = 100pF (Figure 4)	6
Driver Enable or Disable Time	tZLD, tZHD, tLZD, tHZD			180	ns	RL = 500Ω, CL = 50pF, RE = 0V (Figure 5)	6
Driver Enable from Shutdown	tZHSD, tZLSD			9	µs	RL = 500Ω, CL = 50pF, RE = High (Figure 5)	6
Driver Time to Shutdown	tSHDND			180	ns	RL = 500Ω, CL = 50pF, RE = High (Figure 5)	6
Receiver Input to Output	tPLHR, tPHLR		50	65	ns	CL = 15pF, VCM = 1.5V, /VAB/ = 1.5V, tR and tF < 4ns (Figure 6)	6
Differential Receiver Skew	tSKEWR		2	9	ns	CL = 15pF (Figure 6)	6
Receiver Output Rise or Fall Time	tRR, tFR		3	12.5	ns	CL = 15pF (Figure 6)	6
Receiver Enable/Disable Time	tZLR, tZHR, tLZR, tHZR			40	ns	RL = 1k, CL = 15pF, DE = High (Figure 7)	6
Receiver Enable from Shutdown	tZHSR, tZLSR			9	µs	RL = 1k, CL = 15pF, DE = 0V (Figure 7)	6
Receiver Time to Shutdown	tSHDNR			100	ns	RL = 1k, CL = 15pF, DE = 0V (Figure 7)	6
Supply Voltage VCC	VCC	-0.3		6	V		2
Logic Input Voltages (RE, DE, DI)		-0.3		6	V		2
Interface I/O: A, B		-60		60	V		2
Operating Ambient Temperature Range (H-grade)		-40		125	°C	LTC286xH	2
Storage Temperature Range		-65		150	°C		2
Maximum Junction Temperature	TJMAX			150	°C	S8 package	2
Thermal Resistance Junction-to-Ambient	θJA		150		°C/W	S8 package	2
Thermal Resistance Junction-to-Case	θJC		39		°C/W	S8 package	2

CAD (KiCad official)

Symbol: LTC2862HS8-1#PBF
Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
3D model: SO-8 (KiCad packages3D, STEP)
3D model files: ltc2862hs8-1-pbf-etched.step / ltc2862hs8-1-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2862hs8-1-pbf.step / ltc2862hs8-1-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Analog Devices datasheet (26 pp, sha256 156a32e263226c9f, retrieved 2026-10-31, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

LTC2862HS8-1#PBF

Verified LTC2862HS8-1#PBF

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README