3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLKS32MC071C8T8
LINKOSEMI · Microcontroller Units (MCUs/MPUs/SOCs) · TQFP-48(7x7)
LKS32MC071C8T8 from LINKOSEMI, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P0_0 | bidirectional | GPIO P0.0 multiplexes CLKO, MCPWM_BKIN0, UART0_RXD, SPI_DI, CLUOUT0, ADC01_CH4, DAC0_OUT, DAC1_OUT, FLT, EXTI0 and WK0, with a built-in 10kΩ pull-up that software can disable. |
| 2 | P0_2 | bidirectional | P0.2 defaults to the RSTN reset pin; a 10nF to 100nF capacitor to ground and a 10k to 20k pull-up between RSTN and AVDD are recommended, and it can be switched to GPIO. |
| 3 | GND | power_in | Chip ground; multiple ground pins are strongly recommended to be tied together on the PCB. |
| 4 | AVDD | power_in | Chip power supply with a supply range of 2.5 to 5.5 V. |
| 5 | P3_2 | bidirectional | GPIO P3.2 multiplexes MCPWM_CH3P (PWM channel 3 high side) and CLUOUT2. |
| 6 | P0_3 | bidirectional | GPIO P0.3 multiplexes MCPWM_CH4P, SCL, TIM2_CH0, ADC01_CH7 and EXTI3, with a built-in 10kΩ pull-up that software can disable. |
| 7 | P0_4 | bidirectional | GPIO P0.4 multiplexes MCPWM_CH4N, SDA, TIM2_CH1 and ADC01_CH8, with a built-in 10kΩ pull-up that software can disable. |
| 8 | P0_5 | bidirectional | GPIO P0.5 multiplexes HALL_IN0, MCPWM_CH5P, QEP0_Z and ADC01_CH9. |
| 9 | P0_6 | bidirectional | GPIO P0.6 multiplexes HALL_IN1, MCPWM_CH5N, UART1_RXD, SCL, TIM1_CH0, CMP2_IN, FLT, EXTI4 and WK2, with a built-in 10kΩ pull-up that software can disable. |
| 10 | P0_7 | bidirectional | GPIO P0.7 multiplexes HALL_IN2, MCPWM_BKIN1, UART1_TXD, SDA, TIM1_CH1, CMP2_IP0 and FLT, with a built-in 10kΩ pull-up that software can disable. |
| 11 | P2_11 | bidirectional | GPIO P2.11 multiplexes MCPWM_CH1P, TIM2_CH0 and CMP2_IP1. |
| 12 | P2_12 | bidirectional | GPIO P2.12 multiplexes MCPWM_CH1N, SPI_CS, TIM2_CH1, ADC_TRIGGER0, CLUOUT3 and EXTI6. |
| 13 | P0_11 | bidirectional | GPIO P0.11 multiplexes HALL_IN0, TIM3_CH0, ADC1_CH11, CMP0_IP1, FLT, EXTI7 and WK3. |
| 14 | P0_12 | bidirectional | GPIO P0.12 multiplexes HALL_IN1, TIM3_CH1, CAN_RX, ADC1_CH12, CMP0_IP2 and FLT. |
| 15 | P0_13 | bidirectional | GPIO P0.13 multiplexes HALL_IN2, QEP0_Z, CAN_TX, ADC1_CH13, CMP0_IP3 and FLT. |
| 16 | P0_14 | bidirectional | GPIO P0.14 multiplexes CMP0_OUT, MCPWM_BKIN1, UART0_TXD, SPI_CLK, SCL, TIM0_CH1, QEP1_Z, ADC_TRIGGER0, SIF, CLUOUT0, ADC0_CH10, CMP0_IP4, FLT, EXTI8 and WK4, with a built-in 10kΩ pull-up that software can disable. |
| 17 | P0_15 | bidirectional | GPIO P0.15 multiplexes CMP2_OUT, MCPWM_CH0P, UART0_RXD, SPI_DO, SDA, TIM0_CH0, ADC_TRIGGER1, CMP0_IN, FLT and EXTI9, with a built-in 10kΩ pull-up that software can disable. |
| 18 | P1_0 | bidirectional | GPIO P1.0 multiplexes MCPWM_CH0N, UART0_TXD, SPI_DI, TIM0_BKIN and EXTI10, with a built-in 10kΩ pull-up that software can disable. |
| 19 | P1_3 | bidirectional | GPIO P1.3 multiplexes TIM3_CH1 and ADC01_CH5, with a built-in 10kΩ pull-up that software can disable. |
| 20 | P3_5 | input | GPIO P3.5 is the non-inverting (positive) input of operational amplifier 0 (OPA0_IP). |
| 21 | P3_7 | input | GPIO P3.7 is the inverting (negative) input of operational amplifier 0 (OPA0_IN). |
| 22 | P2_7 | bidirectional | GPIO P2.7 multiplexes CLKO, UART0_TXD, TIM0_CH0, TIM3_CH1, ADC_TRIGGER1, CLUOUT1, ADC0_CH11, OPAx_OUT (op-amp output buffer), LDO15 (1.5V LDO output), REF (reference voltage), EXTI11 and WK6, with a built-in 10kΩ pull-up that software can disable. |
| 23 | P3_0 | input | GPIO P3.0 is the non-inverting (positive) input of operational amplifier 1 (OPA1_IP). |
| 24 | P3_1 | input | GPIO P3.1 is the inverting (negative) input of operational amplifier 1 (OPA1_IN). |
| 25 | P2_8 | passive | GPIO P2.8 multiplexes UART1_RXD, SPI_DO, TIM3_CH0 and OSC_IN (external crystal pin), with a built-in 10kΩ pull-up that software can disable. |
| 26 | P3_9 | passive | GPIO P3.9 multiplexes UART1_TXD, TIM3_CH1 and OSC_OUT (external crystal pin), with a built-in 10kΩ pull-up that software can disable. |
| 27 | P1_4 | bidirectional | GPIO P1.4 multiplexes MCPWM_CH0P and QEP0_Z. |
| 28 | P1_5 | bidirectional | GPIO P1.5 is the MCPWM_CH0N (PWM channel 0 low side) function pin. |
| 29 | P1_6 | bidirectional | GPIO P1.6 is the MCPWM_CH1P (PWM channel 1 high side) function pin. |
| 30 | P1_7 | bidirectional | GPIO P1.7 is the MCPWM_CH1N (PWM channel 1 low side) function pin. |
| 31 | P1_8 | bidirectional | GPIO P1.8 is the MCPWM_CH2P (PWM channel 2 high side) function pin. |
| 32 | P1_9 | bidirectional | GPIO P1.9 is the MCPWM_CH2N (PWM channel 2 low side) function pin. |
| 33 | P1_10 | bidirectional | GPIO P1.10 multiplexes MCPWM_CH3P, UART0_RXD, SCL, TIM0_CH0, ADC_TRIGGER0, ADC0_CH13 and EXTI12, with a built-in 10kΩ pull-up that software can disable. |
| 34 | P1_11 | bidirectional | GPIO P1.11 multiplexes MCPWM_CH3N, UART0_TXD, SDA, TIM0_CH1, ADC_TRIGGER1, SIF and CLUOUT2, with a built-in 10kΩ pull-up that software can disable. |
| 35 | P3_10 | bidirectional | GPIO P3.10 multiplexes MCPWM_CH4P and is the non-inverting (positive) input of operational amplifier 2 (OPA2_IP). |
| 36 | P3_11 | bidirectional | GPIO P3.11 multiplexes MCPWM_CH4N and is the inverting (negative) input of operational amplifier 2 (OPA2_IN). |
| 37 | P2_9 | bidirectional | GPIO P2.9 multiplexes MCPWM_CH5P, SPI_DI, SCL, CMP0_IP0 and ADC0_CH12, with a built-in 10kΩ pull-up that software can disable. |
| 38 | P2_10 | bidirectional | GPIO P2.10 multiplexes MCPWM_CH5N, SPI_DO and SDA, with a built-in 10kΩ pull-up that software can disable. |
| 39 | P3_14 | input | GPIO P3.14 is the inverting (negative) input of operational amplifier 3 (OPA3_IN). |
| 40 | P3_15 | input | GPIO P3.15 is the non-inverting (positive) input of operational amplifier 3 (OPA3_IP). |
| 41 | P2_1 | bidirectional | GPIO P2.1 multiplexes SPI_CLK, ADC1_CH10 and CMP1_IP0. |
| 42 | P2_2 | bidirectional | GPIO P2.2 multiplexes QEP1_Z and CMP1_IN (comparator 1 inverting input). |
| 43 | P2_3 | bidirectional | GPIO P2.3 multiplexes CMP1_OUT, MCPWM_BKIN0, SPI_CS, TIM0_CH1, QEP0_Z, CLUOUT3, FLT, and EXTI13. |
| 44 | P2_4 | bidirectional | GPIO P2.4 multiplexes CMP0_OUT, HALL_IN0, MCPWM_CH2P, UART1_RXD, SPI_CLK, TIM1_CH0, TIM2_CH0, ADC_TRIGGER0, CAN_RX, CMP1_IP1, FLT, EXTI14 and WK5, with a built-in 10kΩ pull-up that software can disable. |
| 45 | P2_5 | bidirectional | GPIO P2.5 multiplexes CMP1_OUT, HALL_IN1, MCPWM_CH2N, UART1_TXD, SPI_DO, TIM1_CH1, TIM2_CH1, ADC_TRIGGER1, CAN_TX, CMP1_IP2 and FLT, with a built-in 10kΩ pull-up that software can disable. |
| 46 | P2_6 | bidirectional | GPIO P2.6 multiplexes CMP2_OUT, HALL_IN2, MCPWM_CH3P, TIM0_BKIN, TIM3_CH0, ADC_TRIGGER0, SIF, CLUOUT0, CMP1_IP3 and FLT, with a built-in 10kΩ pull-up that software can disable. |
| 47 | P2_14 | input | GPIO P2.14 carries the SWCLK serial-wire debug clock, also multiplexed with SPI_DI and SCL, with a built-in 10kΩ pull-up that software can disable. |
| 48 | P2_15 | bidirectional | GPIO P2.15 carries the SWDIO serial-wire debug data line, also multiplexed with UART0_RXD, SPI_CS, SDA, TIM2_CH1, CLUOUT1, EXTI15 and WK7, with a built-in 10kΩ pull-up that software can disable. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LINKOSEMI |
| Package | TQFP-48(7x7) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Digital IO output low voltage (max drive current 11.2 mA) | VOL | 0.5 | V | max drive current 11.2mA | 66 | ||
| Digital IO input low voltage | VIL | 0.8 | V | AVDD 3.3V | 66 | ||
| Digital IO input high voltage | VIH | 3.06 | V | AVDD 5V | 66 | ||
| Digital IO input high voltage | VIH | 2.07 | V | AVDD 3.3V | 66 | ||
| Digital IO input high current | IIH | 1 | uA | AVDD 5V or 3.3V (single value printed for both) | 66 | ||
| Digital IO input low current | IIL | -1 | uA | AVDD 5V or 3.3V (single value printed for both) | 66 | ||
| Digital IO input capacitance | CIN | 10 | pF | AVDD 5V or 3.3V (single value printed for both) | 66 | ||
| Pull-up resistor (footnote *) | Rpup | 8 | 12 | kΩ | 66 | ||
| IO to internal analog circuit connection resistance | Rio-ana | 100 | 200 | Ω | 66 | ||
| Electrical limit: power supply voltage (AVDD) | AVDD | -0.3 | 6 | V | 65 | ||
| Electrical limit: pre-driver supply voltage (VCC) | VCC | -0.3 | 25 | V | LKS07x with 6N driver | 65 | |
| Electrical limit: pre-driver supply voltage (VCC) | VCC | -0.3 | 40 | V | LKS07x with 3P3N driver | 65 | |
| Operating temperature | -40 | 105 | ˚C | 65 | |||
| Storage temperature | -40 | 150 | ˚C | 65 | |||
| Junction temperature | 125 | °C | 65 | ||||
| Lead temperature (soldering) | 260 | °C | soldering, 10 s | 65 | |||
| ESD HBM | -6000 | 6000 | V | HBM | 65 | ||
| Latch-up current | -200 | 200 | mA | 85℃ | 65 | ||
| GPIO signal input voltage range | VIN | -0.3 | 6 | V | 65 | ||
| Maximum injection current per GPIO | IINJ_PAD | -11.2 | 11.2 | mA | 65 | ||
| Maximum injection current, all GPIO | IINJ_SUM | -50 | 50 | mA | 65 | ||
| Power supply voltage (AVDD) | AVDD | 2.5 | 5 | 5.5 | V | 65 | |
| Analog operating voltage (AVDDA) | AVDDA | 2.8 | 5 | 5.5 | V | REF2VDD=0, ADC selects 2.4V internal reference | 65 |
| Analog operating voltage (AVDDA) | AVDDA | 2.4 | 5 | 5.5 | V | REF2VDD=1, ADC selects AVDD as reference | 65 |
| Pre-driver supply voltage (VCC) | VCC | 4.5 | 20 | V | 071DO/074DO | 65 |
CAD (KiCad official)
- Symbol:
LKS32MC071C8T8 - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
lks32mc071c8t8-etched.step/lks32mc071c8t8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lks32mc071c8t8.step/lks32mc071c8t8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: LINKOSEMI datasheet (91 pp, sha256
d7b5cc2187fa2830, retrieved 2026-11-13, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).