Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX3226EEUE+

Analog Devices Inc./Maxim Integrated · RS232 ICs · TSSOP-16

MAX3226EEUE+ from Analog Devices Inc./Maxim Integrated, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 READY output Active-high ready-to-transmit output that goes high when V- falls below -4V and the device is ready to transmit.
2 C1+ passive Positive terminal of the voltage-doubler charge-pump capacitor.
3 V+ power_out +5.5V supply generated by the charge pump.
4 C1- passive Negative terminal of the voltage-doubler charge-pump capacitor.
5 C2+ passive Positive terminal of the inverting charge-pump capacitor.
6 C2- passive Negative terminal of the inverting charge-pump capacitor.
7 V- power_out -5.5V supply generated by the charge pump.
8 R1IN input RS-232 receiver input, ESD protected to ±15kV (Human Body Model).
9 R1OUT output TTL/CMOS receiver output.
10 INVALID output Active-low valid signal detector output; a logic high indicates a valid RS-232 level is present on a receiver input.
11 T1IN input TTL/CMOS transmitter input with no pullup resistor; connect to GND or VCC if unused.
12 FORCEON input Active-high force-on input; drive high to override AutoShutdown Plus and keep transmitters and receivers on (FORCEOFF must be high).
13 T1OUT output RS-232 transmitter output, ESD protected to ±15kV (Human Body Model).
14 GND power_in Ground.
15 VCC power_in +3.0V to +5.5V single supply voltage.
16 FORCEOFF input Active-low force-off input; when low, transmitters are high impedance, charge pumps are shut down and receivers are active, overriding AutoShutdown Plus and FORCEON.

Key specifications

Parameter Value
Manufacturer Analog Devices Inc./Maxim Integrated
Package TSSOP-16
Category Communication Interface Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 3 5.5 V VCC = +3V to +5.5V, TA = TMIN to TMAX 6
Operating temperature range (EE grade) TA -40 85 °C MAX32_ EE _ 2
Supply voltage to GND VCC -0.3 6 V VCC to GND 2
V+ to GND V+ -0.3 7 V V+ to GND (Note 1) 2
V- to GND V- -7 0.3 V V- to GND (Note 1) 2
V+ + /V-/ 13 V V+ +/V-/ (Note 1) 2
Input voltage T_IN, FORCEON, FORCEOFF -0.3 6 V to GND 2
Input voltage R_IN -25 25 V to GND 2
Output voltage T_OUT -13.2 13.2 V to GND 2
Storage temperature range TSTG -65 160 °C 2
Lead temperature (soldering, 10s) 300 °C soldering, 10s 2
Thermal resistance junction to ambient, single layer board θJA 106 °C/W 16-TSSOP (U16+1), single layer board 2
Thermal resistance junction to case, single layer board θJC 27 °C/W 16-TSSOP (U16+1), single layer board 2
Thermal resistance junction to ambient, four-layer board θJA 90 °C/W 16-TSSOP (U16+1), four-layer board 2
Thermal resistance junction to case, four-layer board θJC 27 °C/W 16-TSSOP (U16+1), four-layer board 2
Supply Current, AutoShutdown Plus 1 10 μA FORCEON = GND, FORCEOFF = VCC, all R_IN idle, all T_IN idle 6
Supply Current, Shutdown 1 10 μA FORCEOFF = GND 6
Supply Current, AutoShutdown Plus Disabled 0.3 1 mA FORCEON = FORCEOFF = VCC, no load 6
Input Logic Threshold Low 0.8 V T_IN, FORCEON, FORCEOFF 6
Input Logic Threshold High 2 V T_IN, FORCEON, FORCEOFF, VCC = 3.3V 6
Input Logic Threshold High 2.4 V T_IN, FORCEON, FORCEOFF, VCC = 5.0V 6
Transmitter Input Hysteresis 0.5 V 6
Input Leakage Current -1 0.01 1 μA T_IN, FORCEON, FORCEOFF 6
Output Leakage Current R_OUT -10 0.05 10 μA receivers disabled 6
Output Voltage Low 0.4 V IOUT = 1.6mA 6
Receiver Input Voltage Range -25 25 V 6
Input Threshold Low 0.6 1.2 V TA = +25°C, VCC = 3.3V 6
Input Threshold Low 0.8 1.5 V TA = +25°C, VCC = 5.0V 6
Input Threshold High 1.5 2.4 V TA = +25°C, VCC = 3.3V 6
Input Threshold High 1.8 2.4 V TA = +25°C, VCC = 5.0V 6
Input Hysteresis 0.5 V 6
Input Resistance 3 5 7 kΩ TA = +25°C 6
Output Voltage Swing -5 5.4 V All transmitter outputs loaded with 3kΩ to ground 6
Output Resistance 300 Ω VCC = V+ = V- = 0V, transmitter outputs = ±2V 6
Output Short-Circuit Current -60 60 mA 6
Output Leakage Current transmitters -25 25 µA VCC = 0V or 3V to 5.5V, VOUT = ±12V, Transmitters disabled 6
ESD IEC 1000-4-2 Air Discharge -15 15 kV R_IN, T_OUT 7
ESD IEC 1000-4-2 Contact Discharge -8 8 kV R_IN, T_OUT 7
ESD Human Body Model -15 15 kV R_IN, T_OUT 7
Receiver Input Threshold to INVALID Output High, positive threshold 2.7 V AutoShutdown Plus, Figure 4a 7
Receiver Input Threshold to INVALID Output High, negative threshold -2.7 V AutoShutdown Plus, Figure 4a 7
Receiver Input Threshold to INVALID Output Low -0.3 0.3 V Figure 4a 7
INVALID, READY Output Voltage Low 0.4 V IOUT = -1.6mA 7
Receiver Threshold to INVALID High tINVH 1 μs VCC = 5V, Figure 4b 7
Receiver Threshold to INVALID Low tINVL 30 μs VCC = 5V, Figure 4b 7
Receiver or Transmitter Edge to Transmitters Enabled tWU 100 μs VCC = 5V, Figure 5b (Note 2) 7
Receiver or Transmitter Edge to Transmitters Shutdown tAUTOSHDN 15 30 60 s VCC = 5V, Figure 5b (Note 2) 7
Maximum Data Rate 250 kbps RL = 3kΩ, CL = 1000pF, one transmitter switching 8
Receiver Propagation Delay tPHL and tPLH tPHL, tPLH 0.15 μs R_IN to R_OUT, CL = 150pF 8
Transmitter Skew │tPHL - tPLH│ 100 ns (Note 3) 8
Receiver Skew │tPHL - tPLH│ 50 ns 8
Transition-Region Slew Rate 6 30 V/μs VCC = 3.3V, TA = +25°C, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF, one transmitter switching 8

CAD (KiCad official)

  • Symbol: MAX3226EEUE+
  • Footprint: Package_SO:TSSOP-16_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: max3226eeue-etched.step / max3226eeue-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max3226eeue.step / max3226eeue.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices Inc./Maxim Integrated datasheet (25 pp, sha256 8542587c6f3a36a5, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF