3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT1618EDD#TRPBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT1618EDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Feedback pin that sets the output voltage via R1/R2 divider against the 1.263V reference (R1 = R2(VOUT/1.263 - 1)). |
| 2 | ISN | input | Current sense (-) pin, the inverting input to the current sense amplifier. |
| 3 | ISP | input | Current sense (+) pin, the noninverting input to the current sense amplifier. |
| 4 | IADJ | input | Current sense adjust pin; a DC voltage applied reduces the current sense voltage, tie to ground if not needed and do not leave floating. |
| 5 | GND | power_in | Ground pin, tie directly to the local ground plane. |
| 6 | SW | passive | Switch pin for the DD package, connect this pin to pin 7. |
| 7 | SW | passive | Collector of the internal NPN power switch; minimize the metal trace area connected to it to minimize EMI (36V max). |
| 8 | VIN | power_in | Input supply pin (1.6V to 18V), bypass with a capacitor to ground as close to the device as possible. |
| 9 | SHDN | input | Shutdown pin; tie higher than 1V to turn on the LT1618, below 0.3V to turn it off. |
| 10 | VC | passive | Compensation pin for the error amplifier; connect a series RC to ground, typically 2kΩ and 10nF. |
| 11 | Exposed Pad | power_in | Exposed pad is GND and must be soldered to the PCB GND for optimum thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 1.6 | 18 | V | 2 | ||
| Quiescent Current | IQ | 1.8 | 2.7 | mA | VSHDN = 1.6V, Not Switching | 2 | |
| Quiescent Current (shutdown) | IQ | 0.1 | 1 | µA | VSHDN = 0V | 2 | |
| Reference Voltage | VFB | 1.25 | 1.263 | 1.276 | V | Measured at FB Pin | 2 |
| Reference Voltage (full temp range) | VFB | 1.243 | 1.263 | 1.283 | V | Measured at FB Pin, over full operating temperature range | 2 |
| Reference Voltage Line Regulation | 0.01 | 0.03 | %/V | 1.6V < VIN < 18V | 2 | ||
| FB Pin Bias Current | -12 | 12 | nA | VFB = 1.263V, VIN = 1.8V, over full temperature range (typ ±2) | 2 | ||
| Current Sense Voltage (ISP, ISN) | 47.5 | 50 | 52.5 | mV | VFB = 0V, VIADJ = 0V, over full temperature range | 2 | |
| ISP, ISN Pin Bias Currents | 50 | 80 | µA | VISP = 1.85V, VISN = 1.80V, VIADJ = 0V | 2 | ||
| Switching Frequency | 1.25 | 1.4 | 1.6 | MHz | VFB = 1V | 2 | |
| Maximum Switch Duty Cycle | 88 | 92 | % | over full temperature range | 2 | ||
| Switch Current Limit | 1.5 | 2.1 | 2.8 | A | Note 4 | 2 | |
| Switch VCESAT | VCESAT | 200 | 260 | mV | ISW = 1A (Note 4) | 3 | |
| Switch Leakage Current | 0.01 | 5 | µA | Switch Off, VSW = 5V | 3 | ||
| SHDN Pin Current | 5 | 20 | µA | VSHDN = 1.6V | 3 | ||
| Error Amplifier Voltage Gain | 180 | V/V | 2 | ||||
| Error Amplifier Transconductance | 160 | µmho | ∆IC = ± 5µA | 2 | |||
| Error Amplifier Sink Current | 15 | µA | VFB = 1.35V, VC = 1V | 2 | |||
| Error Amplifier Source Current | 30 | µA | VFB = 1.10V, VC = 1V | 2 | |||
| ISP, ISN Common Mode Minimum Voltage | 1.8 | V | 2 | ||||
| Switching Frequency (foldback) | 550 | kHz | VFB = 0V | 2 | |||
| Shutdown Threshold (SHDN Pin) | 0.3 | V | 3 | ||||
| Start-Up Threshold (SHDN Pin) | 1 | V | 3 | ||||
| VIN, SHDN Voltage | 18 | V | 2 | ||||
| SW Voltage | 36 | V | 2 | ||||
| ISP, ISN Voltage | 36 | V | 2 | ||||
| IADJ Voltage | 6 | V | 2 | ||||
| FB Voltage | 1.5 | V | 2 | ||||
| VC Voltage | 1.5 | V | 2 | ||||
| Junction Temperature | TJ | 125 | °C | 2 | |||
| Operating Temperature Range | -40 | 85 | °C | Note 2 | 2 | ||
| Storage Temperature Range (DFN) | -65 | 125 | °C | DFN | 2 | ||
| Thermal Resistance Junction-Ambient | θJA | 43 | °C/W | DD package, TJMAX = 125°C | 2 | ||
| Thermal Resistance Junction-Case | θJC | 3 | °C/W | DD package, TJMAX = 125°C | 2 |
CAD (KiCad official)
- Symbol:
LT1618EDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt1618edd-trpbf-etched.step/lt1618edd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1618edd-trpbf.step/lt1618edd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
afff43abca3e3fd7, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).