Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SE2435L-R

Skyworks Solutions, Inc. · RF Front End Circuits · QFN-24-EP(4x4)

SE2435L-R from Skyworks Solutions, Inc., in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CSD input Shutdown control input, logic high 1.6 V to Vcc and logic low 0 to 0.3 V, used to select the operating mode per Table 6.
2 PA_IN input PA input, fed from the TX filter.
3 CPS input Rx path select control input, logic high 1.6 V to Vcc and logic low 0 to 0.3 V, selecting LNA mode or bypass.
4 CTX input Transmit enable control input, logic high 1.6 V to Vcc and logic low 0 to 0.3 V.
5 TX_FLT output Transmit signal output to the TX filter.
6 TR bidirectional Bi-directional 50 ohm RF signal port to and from the transceiver.
7 ANT_SEL input Antenna select control input, logic low enables ANT1 and logic high enables ANT2, with a maximum input of 3.6 V.
8 GND power_in Ground.
9 LNA_IN input LNA input, fed from the RX filter.
10 N/C unconnected Not connected internally to the device.
11 RX_FLT output Rx signal from the antennas, output to the RX filter.
12 ANT2 bidirectional Antenna port 2, 50 ohm RF interface.
13 N/C unconnected Not connected internally to the device.
14 ANT1 bidirectional Antenna port 1, 50 ohm RF interface.
15 N/C unconnected Not connected internally to the device.
16 TX_IN input TX signal input to the antennas, fed from the output matching network (OMN).
17 N/C unconnected Not connected internally to the device.
18 N/C unconnected Not connected internally to the device.
19 N/C unconnected Not connected internally to the device.
20 PA_OUT output PA output to Z optimum, where Z optimum is 5 ohm for +30 dBm or 8 ohm for +27 dBm POUT.
21 VCC2 power_in Positive power supply, 2.0 to 4.8 V recommended operating range.
22 N/C unconnected Not connected internally to the device.
23 VCC0 power_in Positive power supply, 2.0 to 4.8 V recommended operating range.
24 VCC1 power_in Positive power supply, 2.0 to 4.8 V recommended operating range.
25 GND power_in Exposed die paddle providing electrical and thermal ground, to be connected to PCB ground.

Key specifications

Parameter Value
Manufacturer Skyworks Solutions, Inc.
Package QFN-24-EP(4x4)
Category RF And Wireless
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (no RF) VCC -0.3 5.5 V 2
Operating temperature TA -40 85 °C 2
Storage temperature TSTG -40 125 °C 2
Tx input power at TR port PIN_TX_MAX 10 dBm 2
Rx input power at ANT1 or ANT2 ports PIN_RX_MAX 10 dBm 2
Supply voltage on VCC VCC 2 4 4.8 V 3
Ambient temperature TA -40 25 85 °C 3
Total supply current, transmit mode ICC_TX30 550 mA POUT = +30 dBm 3
Total supply current, transmit mode ICC_TX27 380 mA POUT = +27 dBm 3
Total supply current, transmit mode ICC_TX24 275 mA POUT = +24 dBm 3
Total supply current, receive mode ICC_RX 6 mA 3
Total supply current, receive bypass mode ICC_RXB 280 μA 3
Quiescent current ICQ_TX 50 mA No RF 3
Sleep supply current ICC_OFF 0.05 1 μA No RF 3
Control voltage high VIH 1.6 V 3
Control voltage low VIL 0 0.3 V 3
Input current high IIH 1 μA 3
Input current low IIL 1 μA 3
Frequency range f 860 930 MHz 4
Output power at ANT1 or ANT2 ports in the 900 to 930 MHz frequency range POUT_915 31.5 dBm VCC = 4.8 V 4
Output power at ANT1 or ANT2 ports in the 900 to 930 MHz frequency range POUT_915 30.5 dBm VCC = 4.0 V 4
Output power at ANT1 or ANT2 ports in the 900 to 930 MHz frequency range POUT_915 29.5 dBm VCC = 3.6 V 4
Output power at ANT1 or ANT2 ports in the 900 to 930 MHz frequency range POUT_915 28 dBm VCC = 3.0 V 4
Output power at ANT1 or ANT2 ports in the 860 to 870 MHz frequency range POUT_860 27 dBm VCC = 4.0 V 4
Output power at ANT1 or ANT2 ports in the 860 to 870 MHz frequency range POUT_860 24 dBm VCC = 3.6 V 4
Output power at ANT1 or ANT2 ports in the 860 to 870 MHz frequency range POUT_860 21 dBm VCC = 3.0 V 4
Output power at ANT1 or ANT2 ports in the 860 to 870 MHz frequency range POUT_860 18 dBm VCC = 2.0 V 4
PA power added efficiency PAE_PA 64 % POUT = +28 dBm at PA_OUT port, 915 MHz 4
Small signal gain S21_915 26 dB 900 to 930 MHz 4
Second harmonic 2fo -22 dBc POUT = +30 dBm 4
Third to tenth harmonic 3fo to 10fo -72 dBc POUT = +30 dBm 4
Turn-on time tON 1 µs From 50% of CTX edge to 90% of final RF output power 4
Turn-off time tOFF 1 µs 4
Output return loss S22ANT1 / S22ANT2 -10 -6 dB Into 50 Ω, ANT1 and ANT2 ports 4
Receive gain RX_GAIN 14 16 18 dB 5
Receive noise figure NF 2 2.5 dB 5
Input third order intercept IIP3 -5 -2 dBm 5
Input 1-dB compression point IP1dB -15 -12 dBm 5
Antenna port return loss S11ANT1 / S11ANT2 -12 -8 dB Into 50 Ω, ANT1 and ANT2 ports 5
Turn-on time tON 1 μs From 50% of CTX edge to 90% of final RF output power 5
Turn-off time tOFF 1 μs From 50% of CTX edge to 10% of final RF output power 5
Gain in bypass mode G_bp -3 -2 dB 5
Input 1-dB compression point in bypass mode IP1dB 10 dBm 5
Isolation between ANT1 and ANT2 ports ISOLANTSW -20 dB 5
Insertion loss from TX_IN to ANT1 TX_ANT1 0.8 dB 5
Insertion loss from TX_IN to ANT2 TX_ANT2 0.8 dB 5
Insertion loss from ANT1 to RX_FLT RX_ANT1 0.6 dB 5
Insertion loss from ANT2 to RX_FLT RX_ANT2 0.6 dB 5
Insertion loss from TR to TX_FLT TxRx_Tx 0.5 dB 5
ANT1 to ANT2 switching time transmit mode TANT1-ANT1_TX 800 ns 5
ANT1 to ANT2 switching time receive mode Tant1-ant2_rx 400 ns 5

CAD (KiCad official)

  • Symbol: SE2435L-R
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: se2435l-r-etched.step / se2435l-r-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); se2435l-r.step / se2435l-r.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Skyworks Solutions, Inc. datasheet (13 pp, sha256 d6b15e957f7b301c, retrieved 2026-11-19)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF