3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownWS339E
GEC · RS-485/RS-422 ICs · QFN-40-EP(6x6)
WS339E from GEC, in a QFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | L1 | output | Receiver output R1 in RS-232 mode (MODE1,MODE0=01); held at logic 1 in RS-485/422 modes 10 and 11. |
| 2 | L2 | output | Receiver output R2 in RS-232 mode; carries R1 Output in RS-485 half duplex (10) and full duplex (11) modes. |
| 3 | L3 | input | T1 logic input in RS-232, RS-485 half duplex and full duplex modes (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max). |
| 4 | L4 | input | T2 logic input in RS-232 mode (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max). |
| 5 | L6 | output | Receiver output R3 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11. |
| 6 | L7 | input | T3 logic input in RS-232 mode (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max). |
| 7 | L8 | output | Receiver output R4 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11. |
| 8 | L9 | output | Receiver output R5 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11. |
| 9 | VCC | power_in | Supply voltage, 3.3V ±5% or 5.0V ±5% (absolute maximum -0.3V to +6.0V). |
| 10 | GND | power_in | Ground. |
| 11 | SLEW | input | SLEW=VCC enables 250kbps slew limiting; SLEW=0V allows 1Mbps (RS-232) or 20Mbps (RS-485/422). |
| 12 | DIR1 | input | Driver/receiver direction control: T1 Enable / R1 Disable in the RS-485 modes as listed per mode. |
| 13 | NC | unconnected | This pin is not used and is not connected internally. |
| 14 | MODE0 | input | Mode select bit 0 (MODE1,MODE0: 00 loopback, 01 RS-232, 10 RS-485 half duplex, 11 RS-485/422 full duplex). |
| 15 | MODE1 | input | Mode select bit 1 (MODE1,MODE0: 00 loopback, 01 RS-232, 10 RS-485 half duplex, 11 RS-485/422 full duplex). |
| 16 | NC | unconnected | This pin is not used and is not connected internally. |
| 17 | NC | unconnected | This pin is not used and is not connected internally. |
| 18 | NC | unconnected | This pin is not used and is not connected internally. |
| 19 | ENABLE | input | ENABLE=VCC for operation, ENABLE=0V for shutdown (shutdown current 10µA max). |
| 20 | VCC | power_in | Supply voltage, 3.3V ±5% or 5.0V ±5%. |
| 21 | R9 | input | R5 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD). |
| 22 | R8 | input | R4 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD). |
| 23 | GND | power_in | Ground. |
| 24 | R7 | output | T3 driver output in RS-232 mode (±5.0V min swing into 3kΩ, ±15kV HBM ESD). |
| 25 | R6 | input | R3 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD). |
| 26 | GND | power_in | Ground. |
| 27 | R4 | bidirectional | T2 driver output in RS-232 mode and R1 receiver input B in the RS-485/422 modes (±15kV HBM ESD). |
| 28 | R3 | bidirectional | T1 driver output in RS-232 mode and R2 receiver input A in the RS-485/422 modes (±15kV HBM ESD). |
| 29 | GND | power_in | Ground. |
| 30 | R2 | bidirectional | R2 receiver input in RS-232 mode, R1 input A / T1 output A in the RS-485/422 modes (±15kV HBM ESD). |
| 31 | R1 | bidirectional | R1 receiver input in RS-232 mode, R1 input B / T1 output B in the RS-485/422 modes (±15kV HBM ESD). |
| 32 | VCC | power_in | Supply voltage, 3.3V ±5% or 5.0V ±5%. |
| 33 | V- | power_in | Charge pump negative supply, 0.1uF from ground. |
| 34 | C2- | passive | Charge pump capacitor 2 negative lead. |
| 35 | C1- | passive | Charge pump capacitor 1 negative lead. |
| 36 | GND | power_in | Ground. |
| 37 | C1+ | passive | Charge pump capacitor 1 positive lead, 0.1uF. |
| 38 | VCC | power_in | Supply voltage, 3.3V ±5% or 5.0V ±5%. |
| 39 | C2+ | passive | Charge pump capacitor 2 positive lead, 0.1uF. |
| 40 | V+ | power_in | Charge pump positive supply, 0.1uF to ground. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | GEC |
| Package | QFN-40-EP(6x6) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.3 | 6 | V | 2 | ||
| Receiver Input Voltage (from Ground) | -18 | 18 | V | from Ground | 2 | ||
| Driver Output Voltage (from Ground) | -18 | 18 | V | from Ground | 2 | ||
| Voltage at TTL Input Pins | -0.3 | V | max printed as VCC + 0.5V | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature | 300 | °C | soldering, 10s | 2 | |||
| Power Dissipation 40-pin QFN | 500 | mW | derate 17mW/°C above +70°C | 2 | |||
| Operating Temperature Range | -40 | 85 | °C | ordering information, WS339EER1 | 2 | ||
| Supply voltage tolerance | VCC | -5 | 5 | % | VCC = 3.3V or 5.0V nominal | 6 | |
| ICC Supply Current (RS-232) | ICC | 2 | 8 | mA | No load, idle inputs | 6 | |
| ICC Supply Current (RS-485) | ICC | 2 | 8 | mA | No load, idle inputs | 6 | |
| ICC Vcc Shutdown Current | ICC | 1 | 10 | µA | ENABLE = 0V | 6 | |
| Logic Input Voltage High | VIH | 2 | V | VCC = 3.3V | 6 | ||
| Logic Input Voltage High | VIH | 2.4 | V | VCC = 5.0V | 6 | ||
| Logic Input Voltage Low | VIL | 0.8 | V | 6 | |||
| Logic Input Leakage Current Low | IIL | 1 | µA | Input Low (VIN = 0V) | 6 | ||
| Logic Input Leakage Current High | IIH | 1 | µA | Input High (VIN = VCC), pins 3, 4 and 6 | 6 | ||
| Logic Input Pull-down Current | IPD | 50 | µA | Input High (VIN = VCC), pins 11,12,14,15,17-19 | 6 | ||
| Receiver Output Voltage Low | VOL | 0.4 | V | IOUT = 2.5mA | 6 | ||
| Receiver Output Short Circuit Current | IOSS | -20 | 60 | mA | 0 < VO <VCC | 6 | |
| Receiver Output Leakage Current | IOZ | -0.1 | 1 | µA | 0 < VO < VCC, Receivers disabled | 6 | |
| Input Voltage Range | VIN | -15 | 15 | V | 7 | ||
| Input Threshold Low | VIL | 0.6 | 1.2 | V | VCC = 3.3V | 7 | |
| Input Threshold Low | VIL | 0.8 | 1.5 | V | VCC = 5.0V | 7 | |
| Input Threshold High | VIH | 1.5 | 2 | V | VCC = 3.3V | 7 | |
| Input Threshold High | VIH | 1.8 | 2.4 | V | VCC = 5.0V | 7 | |
| Input Resistance | RIN | 3 | 5 | 7 | kΩ | -15V <VIN <+15V | 7 |
| Output Voltage Swing | VO | -5 | 5.5 | V | Output loaded with 3kΩ to Gnd | 7 | |
| Output Voltage Swing, no load | VO | -7 | 7 | V | No load output | 7 | |
| Short Circuit Current | ISC | -60 | 60 | mA | VO = 0V | 7 | |
| Power Off Impedance | ROFF | 300 | Ω | VCC = 0V, VO = ±2V | 7 | ||
| Power Off Impedance | ROFF | 10 | MΩ | VCC = 0V, VO = ±2V | 7 | ||
| Receiver Input Resistance | RIN | 96 | kΩ | -7V <VIN< +12V | 8 | ||
| Receiver Differential Threshold Voltage | VTH | -200 | -125 | -50 | mV | 8 | |
| Receiver Input Current | IIN | 125 | µA | VIN = +12V | 8 | ||
| Receiver Input Current | IIN | -100 | µA | VIN = -7V | 8 | ||
| Differential Driver Output | VOD | 2 | V | RL = 100Ω (RS-422), Figure 5 | 8 | ||
| Differential Driver Output | VOD | 1.5 | V | RL = 54Ω (RS-485), Figure 5 | 8 | ||
| Change In Magnitude of Differential Output Voltage | ΔVOD | -0.2 | 0.2 | V | RL = 54Ω or 100Ω, Figure 5 | 8 | |
| Driver Output Short Circuit Current | IOSD | -250 | 250 | mA | -7V< VO < +12V, Figure 7 | 8 | |
| Driver Output Leakage Current | IO | 100 | µA | ENABLE = 0V, or DIR1 = 0V and DIR2 = 0V in full duplex modes, VO = +12V, VCC = 0V or 5.25V | 8 | ||
| Driver Output Leakage Current | IO | -100 | µA | ENABLE = 0V, or DIR1 = 0V and DIR2 = 0V in full duplex modes, VO = -7V, VCC = 0V or 5.25V | 8 | ||
| Enable from Shutdown | tENABLE | 1000 | ns | 9 | |||
| Enable to Shutdown | tSHUTDOWN | 1000 | ns | 9 | |||
| Maximum Data Rate (RS-232, SLEW = Vcc) | 250 | kbps | RL = 3kΩ, CL = 1000pF | 9 | |||
| Receiver Propagation Delay (RS-232, 250kbps) | tRHL, tRLH | 100 | ns | CL = 150pF, Figure 8 | 9 | ||
| Driver Propagation Delay (RS-232, 250kbps) | tDHL, tDLH | 1400 | ns | RL = 3kΩ, CL = 2500pF, Figure 9 | 9 | ||
| Transition Region Slew Rate (RS-232, 250kbps) | tSHL, tSLH | 4 | 30 | V/µs | VCC = 3.3V, RL = 3kΩ to 7kΩ, CL = 150pF to 2500pF, Figure 9 | 9 | |
| Maximum Data Rate (RS-232, SLEW = 0V) | 1 | Mbps | RL = 3kΩ, CL = 250pF | 9 | |||
| Receiver Propagation Delay (RS-232, 1Mbps) | tRHL, tRLH | 100 | ns | CL = 150pF, Figure 8 | 9 | ||
| Driver Propagation Delay (RS-232, 1Mbps) | tDHL, tDLH | 300 | ns | RL = 3kΩ, CL = 1000pF, Figure 9 | 9 | ||
| Transition Region Slew Rate (RS-232, 1Mbps) | tSHL, tSLH | 15 | 150 | V/µs | VCC = 3.3V, RL = 3kΩto 7kΩ, CL = 150pF to 1000pF, Figure 9 | 9 | |
| Maximum Data Rate (RS-485/RS-422, 250kbps) | 250 | kbps | RL = 54Ω, CL = 50pF | 10 | |||
| Receiver Propagation Delay (RS-485/422, 250kbps) | tRPHL, tRPLH | 150 | 200 | ns | CL = 15pF, Figure 10 | 10 | |
| Driver Propagation Delay (RS-485/422, 250kbps) | tDPHL, tDPLH | 500 | 1000 | ns | RL = 54Ω, CL = 50pF, Figure 11 | 10 | |
| Driver Rise and Fall Time | tDR, tDF | 300 | 650 | 1200 | ns | 10 | |
| Receiver Output Enable Time | tRZH, tRZL | 200 | ns | CL = 15pF, Figure 12 | 10 | ||
| Driver Output Enable Time | tDZH, tDZL | 1000 | ns | RL = 500Ω, CL = 50pF, Figure 13 | 10 |
CAD (KiCad official)
- Symbol:
WS339E - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: QFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
ws339e-etched.step/ws339e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ws339e.step/ws339e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: GEC datasheet (22 pp, sha256
49d7a31d2d4c982c, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).