component

LM25066IPSQX

Public Made by Adom

by adom

Texas Instruments Surge Protection Devices (SPDs), WQFN-24(4x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.

componentcircuit protectionlm25066ipsqxfactory-2.0.0extractor-text
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

3D Model

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

PCB Footprint

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

Datasheet

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Download PDF
Contents

README

markdown

LM25066IPSQX

Texas Instruments · Surge Protection Devices (SPDs) · WQFN-24(4x5)

LM25066IPSQX from Texas Instruments, in a WQFN-24(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ADR2 input SMBus address line 2 is a three-state strap that must be connected to GND, VDD, or left floating.
2 ADR1 input SMBus address line 1 is a three-state strap that must be connected to GND, VDD, or left floating.
3 ADR0 input SMBus address line 0 is a three-state strap that must be connected to GND, VDD, or left floating.
4 VDD power_out Internally sub-regulated 4.5V bias supply output that requires a 1 µF capacitor to ground for bypassing.
5 CL input Current limit range select: connecting to GND sets the over-current threshold to 25 mV, and connecting to VDD sets it to 46 mV.
6 CB input Circuit breaker range select: connecting to GND sets the trip point to 1.8 times the over-current threshold, and connecting to VDD sets it to 3.6 times.
7 FB input Power Good feedback input, where an external OUT resistor divider sets the PGD switching point at a 1.167 V threshold with an internal 24 µA hysteresis current source.
8 RETRY input Fault retry select: grounding this pin gives continual retries during a fault, while connecting it to VDD latches the device off during a fault.
9 TIMER passive Timing capacitor connection that sets the insertion time delay, fault timeout period and restart timing.
10 PWR input Power limit set: an external resistor here, together with the current sense resistor RS, sets the maximum power dissipation allowed in the external series pass MOSFET.
11 PGD output Open-drain Power Good output that is high when FB is above 1.167 V and the input supply is within its under-voltage and over-voltage thresholds, and that must be pulled up through an external resistor.
12 OUT passive Output feedback connected to the output rail (external MOSFET source), used to determine MOSFET VDS for power limiting and to monitor output voltage; the Out to GND rating is -1 to 20V.
13 GATE output Gate drive output connected to the external MOSFET gate, with the gate voltage limited by an internal 18.8 V zener clamp.
14 SENSE input Current sense input, where the voltage across the current sense resistor RS is measured from VIN to this pin.
15 VIN power_in Positive supply input with an operating range of 2.9 V to 17 V, which should have a small ceramic bypass capacitor placed close to the pin.
16 UVLO/EN input Under-voltage lockout and enable input, where an external divider sets the turn-on threshold, the enable threshold is 1.16 V, and an internal 23 µA hysteresis current source is provided; it can also be used for remote shutdown.
17 OVLO input Over-voltage lockout input, where an external divider sets the turn-off threshold, the disable threshold is 1.16 V, and an internal 23 µA hysteresis current source is provided.
18 GND power_in Circuit ground.
19 SDA bidirectional SMBus data pin.
20 SCL input SMBus clock pin.
21 SMBA output SMBus alert line, active low.
22 VREF power_out Internally generated precision 2.73V reference used for analog-to-digital conversion, which requires a 1 µF capacitor to ground for bypassing.
23 DIODE passive External diode connection for a diode-configured NPN transistor used for temperature monitoring.
24 VAUX input Auxiliary voltage input for telemetry from an external source, with a full-scale input of 1.16 V.
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-24(4x5)
Category Circuit Protection
Pins 25

CAD (KiCad official)

  • Symbol: LM25066IPSQX
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: WQFN-24(4x5) (KiCad packages3D, STEP)
  • 3D model files: lm25066ipsqx-etched.step / lm25066ipsqx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm25066ipsqx.step / lm25066ipsqx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (59 pp, sha256 af8bdb207ef7d7d6, retrieved 2026-10-08, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF