3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32H723VET6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-100(14x14)
STM32H723VET6 from STMicroelectronics, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PE2 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACECLK, SAI1_CK1, USART10_RX and SPI4_SCK. |
| 2 | PE3 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED0, TIM15_BKIN, SAI1_SD_B and USART10_TX. |
| 3 | PE4 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED1, SAI1_D2, SPI4_NSS and DCMI_D4/PSSI_D4. |
| 4 | PE5 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED2, SAI1_CK2, SPI4_MISO and DCMI_D6/PSSI_D6. |
| 5 | PE6 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED3, TIM1_BKIN2, SPI4_MOSI and DCMI_D7/PSSI_D7. |
| 6 | VBAT | power_in | Backup-domain supply input for the RTC and the 32x32-bit backup registers. |
| 7 | PC13 | bidirectional | 5 V tolerant I/O (FT); additional functions RTC_TAMP1/RTC_TS and WKUP4. |
| 8 | PC14-OSC32_IN | bidirectional | 5 V tolerant I/O (FT); OSC32_IN low-speed oscillator input. |
| 9 | PC15-OSC32_OUT | bidirectional | 5 V tolerant I/O (FT); OSC32_OUT low-speed oscillator output. |
| 10 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 11 | VDD | power_in | Standard operating voltage 1.62 V to 3.6 V. |
| 12 | PH0-OSC_IN | bidirectional | 5 V tolerant I/O (FT); OSC_IN high-speed oscillator input. |
| 13 | PH1-OSC_OUT | bidirectional | 5 V tolerant I/O (FT); OSC_OUT high-speed oscillator output. |
| 14 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 15 | PC0 | bidirectional | 5 V tolerant I/O (FT_ha); additional function ADC123_INP10. |
| 16 | PC1 | bidirectional | 5 V tolerant I/O (FT_ha); additional functions ADC123_INN10, ADC123_INP11, RTC_TAMP3 and WKUP6. |
| 17 | PC2_C | passive | Analog-capable 3.3 V tolerant pin (TT_a); additional functions ADC3_INN1 and ADC3_INP0. |
| 18 | PC3_C | passive | Analog-capable 3.3 V tolerant pin (TT_a); additional function ADC3_INP1. |
| 19 | VSSA | power_in | Analog ground reference. |
| 20 | VREF+ | power_in | Positive analog reference voltage pin (supply type S). |
| 21 | VDDA | power_in | Analog operating voltage 1.62 V to 3.6 V when the ADC or COMP is used. |
| 22 | PA0 | bidirectional | 5 V tolerant I/O (FT_ha); additional functions ADC1_INP16 and WKUP1; alternate functions include TIM2_CH1/TIM2_ETR and USART2_CTS. |
| 23 | PA1 | bidirectional | 5 V tolerant I/O (FT_ha); additional functions ADC1_INN16 and ADC1_INP17; alternate functions include TIM2_CH2 and USART2_RTS. |
| 24 | PA2 | bidirectional | 5 V tolerant I/O (FT_ha); additional functions ADC12_INP14 and WKUP2; alternate functions include TIM2_CH3 and ETH_MDIO. |
| 25 | PA3 | bidirectional | 5 V tolerant I/O (FT_ha); additional function ADC12_INP15; alternate functions include TIM2_CH4 and OTG_HS_ULPI_D0. |
| 26 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 27 | VDD | power_in | Standard operating voltage 1.62 V to 3.6 V. |
| 28 | PA4 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INP18 and DAC1_OUT1; alternate functions include SPI1_NSS, SPI3_NSS and USART2_CK. |
| 29 | PA5 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INN18, ADC12_INP19 and DAC1_OUT2; alternate functions include TIM2_CH1 and SPI1_SCK. |
| 30 | PA6 | bidirectional | 5 V tolerant I/O (FT_ha); additional function ADC12_INP3; alternate functions include TIM1_BKIN, TIM3_CH1 and SPI1_MISO. |
| 31 | PA7 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INN3, ADC12_INP7 and OPAMP1_VINM; alternate functions include TIM1_CH1N and SPI1_MOSI. |
| 32 | PC4 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INP4, OPAMP1_VOUT and COMP1_INM; alternate function ETH_MII_RXD0. |
| 33 | PC5 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INN4, ADC12_INP8, OPAMP1_VINM and COMP1_OUT. |
| 34 | PB0 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions ADC12_INN5, ADC12_INP9, OPAMP1_VINP and COMP1_INP; alternate function TIM1_CH2N. |
| 35 | PB1 | bidirectional | 5 V tolerant I/O (FT_ha); additional functions ADC12_INP5 and COMP1_INM; alternate functions include TIM1_CH3N and TIM3_CH4. |
| 36 | PB2 | bidirectional | 5 V tolerant I/O (FT_ha); additional function COMP1_INP; alternate functions include RTC_OUT, SAI4_D1 and TIM23_ETR. |
| 37 | PE7 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions OPAMP2_VOUT and COMP2_INM; alternate functions include TIM1_ETR and UART7_RX. |
| 38 | PE8 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions OPAMP2_VINM and COMP2_OUT; alternate functions include TIM1_CH1N and UART7_TX. |
| 39 | PE9 | bidirectional | 3.3 V tolerant I/O (TT_ha); additional functions OPAMP2_VINP and COMP2_INP; alternate functions include TIM1_CH1 and UART7_RTS/UART7_DE. |
| 40 | PE10 | bidirectional | 5 V tolerant I/O (FT_ha); additional function COMP2_INM; alternate functions include TIM1_CH2N and UART7_CTS. |
| 41 | PE11 | bidirectional | 5 V tolerant I/O (FT_ha); additional function COMP2_INP; alternate functions include TIM1_CH2 and SPI4_NSS. |
| 42 | PE12 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_CH3N, SPI4_SCK and COMP1_OUT. |
| 43 | PE13 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_CH3, SPI4_MISO and COMP2_OUT. |
| 44 | PE14 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_CH4 and SPI4_MOSI. |
| 45 | PE15 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_BKIN, USART10_CK and TIM1_BKIN_COMP12. |
| 46 | PB10 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include TIM2_CH3, LPTIM2_IN1 and I2C2_SCL. |
| 47 | PB11 | bidirectional | 5 V tolerant I/O (FT_f); alternate functions include TIM2_CH4, LPTIM2_ETR and I2C2_SDA. |
| 48 | VCAP | power_in | Connect an external 2.2 uF capacitor (ESR below 100 mOhm) for the main regulator. |
| 49 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 50 | VDD | power_in | Standard operating voltage 1.62 V to 3.6 V. |
| 51 | PB12 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_BKIN, OCTOSPIM_P1_NCLK, I2C2_SMBA and SPI2_NSS. |
| 52 | PB13 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_CH1N, LPTIM2_OUT, SPI2_SCK and FDCAN2_TX. |
| 53 | PB14 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM1_CH2N, TIM12_CH1, USART1_TX and SPI2_MISO. |
| 54 | PB15 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include RTC_REFIN, TIM1_CH3N, USART1_RX and SPI2_MOSI. |
| 55 | PD8 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_CKIN3, USART3_TX and FMC_D13/FMC_AD13. |
| 56 | PD9 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_DATIN3, USART3_RX and FMC_D14/FMC_AD14. |
| 57 | PD10 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_CKOUT, USART3_CK and FMC_D15/FMC_AD15. |
| 58 | PD11 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include LPTIM2_IN2, I2C4_SMBA, USART3_CTS and FMC_A16/FMC_CLE. |
| 59 | PD12 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include LPTIM1_IN1, TIM4_CH1, I2C4_SCL and FDCAN3_RX. |
| 60 | PD13 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include LPTIM1_OUT, TIM4_CH2, I2C4_SDA and FDCAN3_TX. |
| 61 | PD14 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM4_CH3, UART8_CTS, UART9_RX and FMC_D0/FMC_AD0. |
| 62 | PD15 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM4_CH4, UART8_RTS, UART9_TX and FMC_D1/FMC_AD1. |
| 63 | PC6 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM3_CH1, TIM8_CH1, I2S2_MCK and USART6_TX. |
| 64 | PC7 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM3_CH2, TIM8_CH2, I2S3_MCK and USART6_RX. |
| 65 | PC8 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED1, TIM3_CH3, TIM8_CH3 and USART6_CK. |
| 66 | PC9 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include MCO2, TIM3_CH4, TIM8_CH4 and I2C3_SDA. |
| 67 | PA8 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include MCO1, TIM1_CH1, I2C3_SCL and USART1_CK. |
| 68 | PA9 | bidirectional | USB option I/O (FT_u, supplied by VDD33USB); alternate functions include TIM1_CH2, LPUART1_TX and USART1_TX; additional function OTG_HS_VBUS. |
| 69 | PA10 | bidirectional | USB option I/O (FT_u, supplied by VDD33USB); alternate functions include TIM1_CH3, LPUART1_RX and USART1_RX; additional function OTG_HS_ID. |
| 70 | PA11 | bidirectional | USB option I/O (FT_u, supplied by VDD33USB); alternate functions include TIM1_CH4, LPUART1_CTS and USART1_CTS; additional function OTG_HS_DM. |
| 71 | PA12 | bidirectional | USB option I/O (FT_u, supplied by VDD33USB); alternate functions include TIM1_ETR, LPUART1_RTS and USART1_RTS; additional function OTG_HS_DP. |
| 72 | PA13 | bidirectional | 5 V tolerant I/O (FT); debug function JTMS/SWDIO. |
| 73 | VCAP | power_in | Connect an external 2.2 uF capacitor (ESR below 100 mOhm) for the main regulator. |
| 74 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 75 | VDD | power_in | Standard operating voltage 1.62 V to 3.6 V. |
| 76 | PA14 | bidirectional | 5 V tolerant I/O (FT); debug function JTCK/SWCLK. |
| 77 | PA15 | bidirectional | 5 V tolerant I/O (FT); alternate functions include JTDI, TIM2_CH1/TIM2_ETR, SPI1_NSS and SPI3_NSS. |
| 78 | PC10 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include DFSDM1_CKIN5, I2C5_SDA, SPI3_SCK and USART3_TX. |
| 79 | PC11 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include DFSDM1_DATIN5, I2C5_SCL, SPI3_MISO and USART3_RX. |
| 80 | PC12 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED3, FMC_D6/FMC_AD6, TIM15_CH1 and USART3_CK. |
| 81 | PD0 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_CKIN6, UART4_RX, FDCAN1_RX and FMC_D2/FMC_AD2. |
| 82 | PD1 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_DATIN6, UART4_TX, FDCAN1_TX and FMC_D3/FMC_AD3. |
| 83 | PD2 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TRACED2, FMC_D7/FMC_AD7, TIM3_ETR, UART5_RX and SDMMC1_CMD. |
| 84 | PD3 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_CKOUT, SPI2_SCK, USART2_CTS and FMC_CLK. |
| 85 | PD4 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include USART2_RTS, OCTOSPIM_P1_IO4 and FMC_NOE. |
| 86 | PD5 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include USART2_TX, OCTOSPIM_P1_IO5 and FMC_NWE. |
| 87 | PD6 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include SAI1_D1, DFSDM1_DATIN1, USART2_RX and FMC_NWAIT. |
| 88 | PD7 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include DFSDM1_DATIN4, SPI1_MOSI, USART2_CK and FMC_NE1. |
| 89 | PB3 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include JTDO/TRACESWO, TIM2_CH2, SPI1_SCK and SPI3_SCK. |
| 90 | PB4 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include NJTRST, TIM16_BKIN, TIM3_CH1 and SPI1_MISO. |
| 91 | PB5 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include TIM17_BKIN, TIM3_CH2, I2C1_SMBA and SPI1_MOSI. |
| 92 | PB6 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include TIM16_CH1N, TIM4_CH1, I2C1_SCL and USART1_TX. |
| 93 | PB7 | bidirectional | 5 V tolerant I/O (FT_fa); additional function PVD_IN; alternate functions include TIM17_CH1N, I2C1_SDA and USART1_RX. |
| 94 | BOOT0 | input | Dedicated BOOT0 input pin; input voltage range is VSS to 9.0 V. |
| 95 | PB8 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include TIM16_CH1, I2C1_SCL, UART4_RX and FDCAN1_RX. |
| 96 | PB9 | bidirectional | 5 V tolerant I/O (FT_fh); alternate functions include TIM17_CH1, I2C1_SDA, SPI2_NSS and UART4_TX. |
| 97 | PE0 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include LPTIM1_ETR, TIM4_ETR, UART8_RX and FMC_NBL0. |
| 98 | PE1 | bidirectional | 5 V tolerant I/O (FT_h); alternate functions include LPTIM1_IN2, UART8_TX and FMC_NBL1. |
| 99 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 100 | VDD | power_in | Standard operating voltage 1.62 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDLDO, VDDA, VDD33USB, VBAT) | VDDX - VSS | -0.3 | 4 | V | 88 | ||
| Input voltage on FT_xxx pins | VIN | -0.3 | V | max = Min(VDD, VDDA, VDD33USB, VBAT) + 4.0 V | 88 | ||
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | 88 | ||
| Input voltage on BOOT0 pin | VIN | 9 | V | min = VSS | 88 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 88 | ||
| Total current into sum of all VDD power lines (source) | ΣIVDD | 620 | mA | 89 | |||
| Total current out of sum of all VSS ground lines (sink) | ΣIVSS | 620 | mA | 89 | |||
| Maximum current into each VDD power pin (source) | IVDD | 100 | mA | 89 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS | 100 | mA | 89 | |||
| Output current sunk by any I/O and control pin | IIO | 20 | mA | 89 | |||
| Total output current sunk by sum of all I/Os and control pins | ΣI(PIN) | 140 | mA | 89 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣI(PIN) | 140 | mA | 89 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins except PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 89 | ||
| Total injected current (sum of all I/Os and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 89 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 89 | ||
| Maximum junction temperature | TJ | 125 | °C | Industrial temperature range 6 | 89 | ||
| Standard operating voltage | VDD | 1.62 | 3.6 | V | 90 | ||
| Supply voltage for the internal regulator | VDDLDO | 1.62 | 3.6 | V | VDDLDO ≤ VDD | 90 | |
| Standard operating voltage, USB domain | VDD33USB | 3 | 3.6 | V | USB used | 90 | |
| Standard operating voltage, USB domain | VDD33USB | 0 | 3.6 | V | USB not used | 90 | |
| Analog operating voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 90 | |
| Analog operating voltage | VDDA | 1.8 | V | DAC used | 90 | ||
| Analog operating voltage | VDDA | 2 | V | OPAMP used | 90 | ||
| Analog operating voltage | VDDA | 0 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 90 | ||
| I/O input voltage (TT_xx) | VIN | -0.3 | V | max = VDD + 0.3 V | 90 | ||
| I/O input voltage (BOOT0) | VIN | 0 | 9 | V | 90 | ||
| I/O input voltage (all I/O except BOOT0 and TT_xx) | VIN | -0.3 | V | max = Min(VDD, VDDA, VDD33USB) + 3.6 V, when < 5.5 V | 90 | ||
| Internal regulator ON (LDO) core voltage, VOS3 | VCORE | 0.95 | 1 | 1.05 | V | Internal regulator ON (LDO), VOS3 | 90 |
| Internal regulator ON (LDO) core voltage, VOS2 | VCORE | 1.05 | 1.1 | 1.15 | V | Internal regulator ON (LDO), VOS2 | 90 |
| Internal regulator ON (LDO) core voltage, VOS1 | VCORE | 1.15 | 1.21 | 1.26 | V | Internal regulator ON (LDO), VOS1 | 90 |
| Internal regulator ON (LDO) core voltage, VOS0 | VCORE | 1.3 | 1.36 | 1.4 | V | Internal regulator ON (LDO), VOS0 | 90 |
| Arm Cortex-M7 clock frequency, VOS3 | fCPU | 170 | MHz | VOS3 | 91 | ||
| Arm Cortex-M7 clock frequency, VOS2 | fCPU | 300 | MHz | VOS2 | 91 | ||
| Arm Cortex-M7 clock frequency, VOS1 | fCPU | 400 | MHz | VOS1 | 91 | ||
| Arm Cortex-M7 clock frequency, VOS0 | fCPU | 520 | MHz | VOS0 | 91 | ||
| Arm Cortex-M7 clock frequency, VOS0 with CPU_FREQ_BOOST | fCPU | 550 | MHz | VOS0 and CPU_FREQ_BOOST | 91 | ||
| Ambient temperature, temperature range 6 | TA | -40 | 85 | °C | Maximum power dissipation | 91 | |
| Ambient temperature, temperature range 6 | TA | -40 | 105 | °C | Low-power dissipation | 91 | |
| Power-on/power-down reset threshold (rising edge) | VPOR/PDR | 1.62 | 1.67 | 1.71 | V | Rising edge | 94 |
| Power-on/power-down reset threshold (falling edge) | VPOR/PDR | 1.58 | 1.62 | 1.68 | V | Falling edge | 94 |
| Brown-out reset threshold 1 (rising edge) | VBOR1 | 2.04 | 2.1 | 2.15 | V | Rising edge | 94 |
| Brown-out reset threshold 1 (falling edge) | VBOR1 | 1.95 | 2 | 2.06 | V | Falling edge | 94 |
| POR and PVD consumption from VDD | IDD_POR_PVD | 0.8 | 1.2 | µA | 94 | ||
| BOR and PVD consumption from VDD | IDD_BOR_PVD | 0.63 | µA | 94 | |||
| Internal reference voltages | VREFINT | 1.18 | 1.216 | 1.255 | V | -40°C < TJ < TJmax | 95 |
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 15 | mV | -40°C < TJ < TJmax | 95 | |
| Average temperature coefficient | Tcoeff | 20 | 70 | ppm/°C | 95 | ||
| Average voltage coefficient | VDDcoeff | 10 | 1370 | ppm/V | 3.0 V < VDD < 3.6 V | 95 | |
| Reference buffer consumption for ADC | Irefbuf | 9 | 13.5 | 23 | µA | VDD = 3.3 V | 95 |
| Regulated output voltage | VREGOUTV33V | 3 | 3.6 | V | 96 | ||
| Output current load sinked by USB block | IOUT | 20 | mA | 96 | |||
| User external clock source frequency | fHSE_ext | 4 | 25 | 50 | MHz | 105 | |
| HSI48 frequency | fHSI48 | 47.5 | 48 | 48.5 | MHz | VDD=3.3 V, TJ=30 °C | 109 |
| Accuracy of the HSI48 oscillator over temperature (factory calibrated) | ACCHSI48_REL | -4.5 | 3.5 | % | TJ=-40 to 125 °C | 109 | |
| HSI48 oscillator power consumption | IDD(HSI48) | 350 | 400 | µA | 109 | ||
| HSI48 oscillator frequency drift with VDD (reference 3.3 V) | ΔVDD(HSI48) | 0.025 | 0.05 | % | VDD=3 to 3.6 V | 109 | |
| HSI48 oscillator frequency drift with VDD (reference 3.3 V) | ΔVDD(HSI48) | 0.05 | 0.1 | % | VDD=1.62 V to 3.6 V | 109 | |
| Duty cycle | DuCy(HSI48) | 45 | 55 | % | 109 | ||
| HSI48 oscillator start-up time | tsu(HSI48) | 2.1 | 4 | µs | 109 | ||
| Maximum BOR and PVD consumption, see IDD_BOR_PVD | IDD_BOR_PVD | 0.63 | µA | 94 |
CAD (KiCad official)
- Symbol:
STM32H723VET6 - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
stm32h723vet6-etched.step/stm32h723vet6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32h723vet6.step/stm32h723vet6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (225 pp, sha256
c3741ebfd15024ac, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).