3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRE46C141SW16TF
Microchip Tech · Specialized Sensors · SOIC-16-300mil
RE46C141SW16TF from Microchip Tech, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1 | passive | The capacitor on this pin sets the high photo-amplifier gain used for push-to-test and chamber sensitivity test, with A = 1 + (C1/10) where C1 is in pF, and the gain should be <10000. |
| 2 | C2 | passive | The capacitor on this pin sets the normal photo-amplifier gain during standby, with A = 1 + (C2/10) where C2 is in pF. |
| 3 | DETECT | input | Positive input to the photo amplifier, normally connected to the cathode of an external photodiode operated at zero bias. |
| 4 | STROBE | output | Regulated output voltage of VDD-5 that is active during a smoke test and forms the negative side of the photo amplifier circuitry. |
| 5 | VDD | power_in | Connect to the positive supply voltage. |
| 6 | IRED | output | Provides a regulated pulsed output voltage pre-driver for the infrared emitter, usually driving the base of an NPN transistor. |
| 7 | IO | bidirectional | Bidirectional pin that allows many detectors to be interconnected in a single system and has an internal pull-down device. |
| 8 | HORNB | output | Connected to the metal electrode of a piezoelectric transducer. |
| 9 | HORNS | output | Complementary output to HORNB that connects to the ceramic electrode of the piezoelectric transducer. |
| 10 | FEED | input | Usually connected to the feedback electrode through a current limiting resistor; if not used, this pin must be connected to VDD or VSS. |
| 11 | LED | output | Open-drain NMOS output used to drive a visible LED. |
| 12 | COSC | passive | A capacitor connected to this pin with a parallel resistor sets the internal clock low time, which is approximately the clock period. |
| 13 | ROSC | passive | A resistor between this pin and COSC (pin 12) sets the internal clock high time and also sets the IRED pulse width (100-200 uS). |
| 14 | VSS | power_in | Connect to the negative supply voltage. |
| 15 | LBSET | input | Input connected to a VDD reference voltage to set the low battery warning voltage. |
| 16 | TEST | input | Input used to invoke two test modes; it has an internal pull-down. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-16-300mil |
| Category | Sensors |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 12.5 | V | 1 | |||
| Input Voltage Range Except FEED | Vin | -0.3 | V | Except FEED; upper limit printed as Vdd +.3 V | 1 | ||
| FEED Input Voltage Range | Vinfd | -10 | 22 | V | 1 | ||
| IO Input Voltage Range | Vio1 | -0.3 | 17 | V | 1 | ||
| Input Current except FEED | Iin | 10 | mA | 1 | |||
| Operating Temperature | TA | -25 | 75 | °C | 1 | ||
| Storage Temperature | TSTG | -55 | 125 | °C | 1 | ||
| Maximum Junction Temperature | TJ | 150 | °C | 1 | |||
| Supply Voltage | VDD | 6 | 12 | V | Operating, pin 5 | 2 | |
| Supply Current | IDD1 | 4 | 6 | uA | Configured as in Figure 2, COSC=VSS | 2 | |
| Supply Current | IDD2 | 5.5 | 8 | uA | Configured as in Figure 2, VDD=12V, COSC=VSS | 2 | |
| Supply Current | IDD3 | 2 | mA | Configured as in Figure 2, STROBE on, IRED off, VDD=12V | 2 | ||
| Supply Current | IDD4 | 3 | mA | Configured as in Figure 2, STROBE on, IRED on, VDD=12V, Note 1 | 2 | ||
| Input Voltage High FEED | VIH1 | 4.5 | 6.2 | V | 2 | ||
| Input Voltage High IO | VIH2 | 3.2 | V | No Local Alarm, IO as an Input | 2 | ||
| Input Voltage High TEST | VIH4 | 8.5 | V | 2 | |||
| Input Voltage Low FEED | VIL1 | 2.7 | 4.5 | V | 2 | ||
| Input Voltage Low IO | VIL2 | 1.5 | V | No Local Alarm, IO as an Input | 2 | ||
| Input Voltage Low TEST | VIL4 | 7 | V | 2 | |||
| Input Leakage Low pin 16 | IIL3 | -1 | uA | VDD=12V, Vin=VSS | 2 | ||
| Input Leakage Low FEED | ILFD | -50 | uA | FEED=-10V | 2 | ||
| Input Leakage High FEED | IHFD | 50 | uA | FEED=22V | 2 | ||
| Input Pull Down Current pin 16 | IPD1 | 0.25 | 10 | uA | Vin=VDD | 2 | |
| Input Pull Down Current pin 7 | IPDIO1 | 20 | 80 | uA | Vin=VDD | 2 | |
| Output Leakage Current Low | IOZL1 | -1 | uA | Output Off, Output=VSS | 2 | ||
| Output Leakage Current High | IOZH1 | 1 | uA | Output Off, Output=VDD | 2 | ||
| Output Voltage Low | VOL1 | 1 | V | Iol=16mA, VDD=6.5V | 3 | ||
| Output Voltage Low | VOL2 | 0.5 | V | Iol=5mA, VDD=6.5V | 3 | ||
| Output Voltage Low | VOL3 | 0.6 | V | Iol=10mA, VDD=6.5V | 3 | ||
| Output Voltage High | VOH1 | 5.5 | V | Ioh=-16mA, VDD=6.5V | 3 | ||
| I Output Current | IOH1 | -16 | -4 | mA | Alarm, Vio=Vdd-2V or Vio=0V | 3 | |
| IO Discharge Current | IIODMP | 5 | mA | At Conclusion of Local Alarm or Test, Vio=1V | 3 | ||
| Low Battery Alarm Voltage | VLB | 6.9 | 7.2 | 7.5 | V | R14=100K, R15=47K | 3 |
| Output Voltage STROBE off | VSTOF | -0.1 | V | STROBE off, VDD=12V, Iout=-1uA; limit printed as VDD - .1 | 3 | ||
| Output Voltage STROBE on | VSTON | -5.3 | -5 | -4.7 | V | STROBE on, VDD=9V, Iout= 100uA to 500uA; limits printed as VDD - 5.3, VDD - 5, VDD - 4.7 | 3 |
| Output Voltage IRED off | VIREDOF | 0.1 | V | IRED off, VDD=12V, Iout=1uA | 3 | ||
| Output Voltage IRED on | VIREDON | 2.25 | 3.1 | 3.75 | V | IRED on, VDD=9V, Iout=0 to -6mA, Ta=25C | 3 |
| Common Mode Voltage | VCM1 | 0.5 | V | Local smoke, Push to Test or Chamber Test, Note 1; upper limit printed as VDD-2 | 3 | ||
| Smoke Comparator Reference, Internal Reference | Vref | -3.85 | -3.15 | V | limits printed as VDD-3.85 and VDD-3.15 | 3 | |
| Oscillator Period | TPOSC | 7.1 | 7.9 | 8.6 | mS | No Alarm Condition, Note 2 | 4 |
| LED and STROBE On Time | TON1 | 7.1 | 7.9 | 8.6 | mS | Operating | 4 |
| LED Period Standby | TPLED1 | 28.8 | 32.4 | 35.2 | S | Standby, No Alarm | 4 |
| LED Period Local Alarm | TPLED2 | 0.45 | 0.5 | 0.55 | S | Local Alarm Condition | 4 |
| STROBE and IRED Pulse Period Standby | TPER1 | 7.3 | 8.1 | 8.8 | S | Standby, No Alarm | 4 |
| STROBE and IRED Pulse Period After 1 Sample | TPER1A | 1.8 | 2 | 2.2 | S | Standby, After 1 Valid Smoke Sample | 4 |
| STROBE and IRED Pulse Period After 2 Samples | TPER1B | 0.9 | 1 | 1.1 | S | Standby, After 2 Consecutive Valid Smoke Samples | 4 |
| STROBE and IRED Pulse Period Local Alarm | TPER2 | 0.9 | 1 | 1.1 | S | In Local Alarm, (3 Consecutive Valid Smoke Samples) | 4 |
| STROBE and IRED Pulse Period Chamber or Low Battery Test | TPER5 | 28.8 | 35.2 | S | Chamber Test or Low Battery Test, no Alarms | 4 | |
| IRED On Time | TON2 | 94 | 104 | 115 | uS | Operating, Note 2 | 4 |
| Horn On Time | THON1 | 450 | 500 | 550 | mS | Operating, Alarm Condition, Note 1 | 4 |
| Horn On Time Low Battery or Failed Chamber Test | THON2 | 7.1 | 7.9 | 8.6 | mS | Low Battery or Failed Chamber Test, No Alarm | 4 |
| Horn Off Time | THOF1 | 450 | 500 | 550 | mS | Operating, Alarm Condition, Note 1 | 4 |
| Horn Off Time Alarm | THOF2 | 1.35 | 1.5 | 1.65 | S | Operating, Alarm Condition, Note 1 | 4 |
| Horn Off Time Low Battery or Failed Chamber Test | THOF3 | 28.8 | 32.4 | 35.2 | S | Low Battery or Failed Chamber Test, No Alarm | 4 |
| IO Charge Dump Duration | TIODMP | 0.68 | 1.1 | S | At Conclusion of Local Alarm or Test | 4 | |
| IO Filter | TIOFILT | 450 | mS | IO pulse width guaranteed to be filtered. IO as Input, No Local Alarm | 4 | ||
| Remote Alarm Delay | TIODLY2 | 0.9 | 1.65 | S | No Local Alarm, From IO Active Horn Active | 4 | |
| Temperature Coefficient STROBE Output Voltage | TCST | 0.01 | %/ºC | VDD=6V to 12V, STROBE Output Voltage | 3 | ||
| Temperature Coefficient IRED Output Voltage | TCIRED | 0.3 | %/ºC | VDD=6V to 12V, IRED Output Voltage | 3 |
CAD (KiCad official)
- Symbol:
RE46C141SW16TF - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
re46c141sw16tf-etched.step/re46c141sw16tf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);re46c141sw16tf.step/re46c141sw16tf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet, copy hosted by LCSC (12 pp, sha256
adf2921c8e518841, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).