3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownPIC16LF73-I/SS
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SSOP-28-208mil
PIC16LF73-I from Microchip Tech, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Master Clear (Reset) input, an active low RESET to the device, or programming voltage input (VPP) during programming. |
| 2 | RA0/AN0 | bidirectional | Digital I/O pin RA0 with analog input 0 on TTL input levels. |
| 3 | RA1/AN1 | bidirectional | Digital I/O pin RA1 with analog input 1 on TTL input levels. |
| 4 | RA2/AN2 | bidirectional | Digital I/O pin RA2 with analog input 2 on TTL input levels. |
| 5 | RA3/AN3/VREF | bidirectional | Digital I/O pin RA3 with analog input 3, which also serves as the A/D reference voltage input VREF. |
| 6 | RA4/T0CKI | bidirectional | Digital I/O pin RA4 that is open drain when configured as an output, and serves as the Timer0 external clock input (Schmitt Trigger). |
| 7 | RA5/SS/AN4 | bidirectional | Digital I/O pin RA5 with SPI slave select input and analog input 4 on TTL input levels. |
| 8 | VSS | power_in | Ground reference for logic and I/O pins. |
| 9 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input, with Schmitt Trigger buffer in RC mode and CMOS otherwise. |
| 10 | OSC2/CLKOUT | output | Oscillator crystal output connecting to a crystal or resonator, or in RC mode outputs CLKO at 1/4 the OSC1 frequency denoting the instruction cycle rate. |
| 11 | RC0/T1OSO/T1CKI | bidirectional | Digital I/O pin RC0 that serves as Timer1 oscillator output or Timer1 external clock input (Schmitt Trigger). |
| 12 | RC1/T1OSI/CCP2 | bidirectional | Digital I/O pin RC1 that serves as Timer1 oscillator input or Capture2 input, Compare2 output and PWM2 output. |
| 13 | RC2/CCP1 | bidirectional | Digital I/O pin RC2 that serves as Capture1 input, Compare1 output or PWM1 output. |
| 14 | RC3/SCK/SCL | bidirectional | Digital I/O pin RC3 that serves as the synchronous serial clock input/output for SPI mode or I2C mode. |
| 15 | RC4/SDI/SDA | bidirectional | Digital I/O pin RC4 that serves as the SPI data input or I2C data I/O. |
| 16 | RC5/SDO | bidirectional | Digital I/O pin RC5 that serves as the SPI data output. |
| 17 | RC6/TX/CK | bidirectional | Digital I/O pin RC6 that serves as the USART asynchronous transmit or USART synchronous clock. |
| 18 | RC7/RX/DT | bidirectional | Digital I/O pin RC7 that serves as the USART asynchronous receive or USART synchronous data. |
| 19 | VSS | power_in | Ground reference for logic and I/O pins. |
| 20 | VDD | power_in | Positive supply for logic and I/O pins. |
| 21 | RB0/INT | bidirectional | Digital I/O pin RB0 that serves as external interrupt input, with Schmitt Trigger buffer when configured as the interrupt; PORTB has software-programmable weak pull-up on all inputs. |
| 22 | RB1 | bidirectional | Digital I/O pin RB1 on TTL input levels, with software-programmable weak pull-up available on PORTB. |
| 23 | RB2 | bidirectional | Digital I/O pin RB2 on TTL input levels, with software-programmable weak pull-up available on PORTB. |
| 24 | RB3/PGM | bidirectional | Digital I/O pin RB3 that serves as the low voltage ICSP programming enable pin. |
| 25 | RB4 | bidirectional | Digital I/O pin RB4 on TTL input levels, with software-programmable weak pull-up available on PORTB. |
| 26 | RB5 | bidirectional | Digital I/O pin RB5 on TTL input levels, with software-programmable weak pull-up available on PORTB. |
| 27 | RB6/PGC | bidirectional | Digital I/O pin RB6 that serves as the In-Circuit Debugger and ICSP programming clock (Schmitt Trigger in serial programming mode). |
| 28 | RB7/PGD | bidirectional | Digital I/O pin RB7 that serves as the In-Circuit Debugger and ICSP programming data (Schmitt Trigger in serial programming mode). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SSOP-28-208mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.5 | 5.5 | V | PIC16LF7X, A/D in use, -40°C to +85°C | 123 | |
| Supply Voltage | VDD | 2.2 | 5.5 | V | PIC16LF7X, A/D in use, 0°C to +85°C | 123 | |
| Supply Voltage | VDD | 2 | 5.5 | V | PIC16LF7X, A/D not used, -40°C to +85°C | 123 | |
| Brown-out Reset Voltage | VBOR | 3.65 | 4 | 4.35 | V | BODEN bit in configuration word enabled | 123 |
| VDD Rise Rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | See section on Power-on Reset for details | 123 | ||
| RAM Data Retention Voltage | VDR | 1.5 | V | 123 | |||
| Supply Current | IDD | 0.4 | 2 | mA | XT, RC osc configuration, FOSC = 4 MHz, VDD = 3.0V (Note 4) | 124 | |
| Supply Current | IDD | 20 | 48 | µA | LP osc configuration, FOSC = 32 kHz, VDD = 3.0V, WDT disabled | 124 | |
| Power-down Current | IPD | 2 | 30 | µA | VDD = 3.0V, WDT enabled, -40°C to +85°C | 124 | |
| Power-down Current | IPD | 0.1 | 5 | µA | VDD = 3.0V, WDT disabled, -40°C to +85°C | 124 | |
| Brown-out Reset Current | ∆IBOR | 25 | 200 | µA | BOR enabled, VDD = 5.0V | 124 | |
| PORTB Weak Pull-up Current | IPURB | 50 | 250 | 400 | µA | VDD = 5V, VPIN = VSS | 125 |
| Input Low Voltage, I/O ports with TTL buffer | VIL | 0.8 | V | 4.5V ≤ VDD ≤ 5.5V | 125 | ||
| Input Low Voltage, OSC1 in XT and LP mode | VIL | 0.3 | V | OSC1 (in XT and LP mode) | 125 | ||
| Input High Voltage, I/O ports with TTL buffer | VIH | 2 | V | 4.5V ≤ VDD ≤ 5.5V | 125 | ||
| Input High Voltage, OSC1 in XT and LP mode | VIH | 1.6 | V | OSC1 (in XT and LP mode) | 125 | ||
| Input Leakage Current, I/O ports | IIL | -1 | 1 | µA | Vss ≤ VPIN ≤ VDD, pin at hi-impedance | 125 | |
| Input Leakage Current, MCLR, RA4/T0CKI | IIL | -5 | 5 | µA | Vss ≤ VPIN ≤ VDD | 125 | |
| Input Leakage Current, OSC1 | IIL | -5 | 5 | µA | Vss ≤ VPIN ≤ VDD, XT, HS and LP osc configuration | 125 | |
| Output Low Voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +125°C | 126 | ||
| Output Low Voltage, OSC2/CLKOUT (RC osc config) | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40°C to +125°C | 126 | ||
| Open Drain High Voltage, RA4 pin | VOD | 12 | V | RA4 pin | 126 | ||
| OSC2 pin capacitive loading | COSC2 | 15 | pF | In XT, HS and LP modes when external clock is used to drive OSC1 | 126 | ||
| All I/O pins and OSC2 (RC mode) capacitive loading | CIO | 50 | pF | All I/O pins and OSC2 (in RC mode) | 126 | ||
| SCL, SDA capacitive loading in I2C mode | CB | 400 | pF | SCL, SDA in I2C mode | 126 | ||
| Endurance | EP | 100 | 1000 | E/W | 25°C at 5V | 126 | |
| VDD for Read | VPR | 2 | 5.5 | V | 126 | ||
| Reference voltage | VREF | 2.2 | 5.5 | V | 0°C to +125°C | 139 | |
| Recommended impedance of analog voltage source | ZAIN | 10 | kΩ | 139 | |||
| A/D conversion current (VDD) | IAD | 90 | µA | PIC16LF7X, average current consumption when A/D is on (Note 1) | 139 | ||
| VREF input current during VAIN acquisition | IREF | -5 | 5 | µA | During VAIN acquisition | 139 | |
| VREF input current during A/D conversion cycle | IREF | 500 | µA | During A/D Conversion cycle | 139 | ||
| External clock in (OSC1) high or low time | TosL,TosH | 15 | ns | HS oscillator | 126 | ||
| External clock in (OSC1) rise or fall time | TosR,TosF | 25 | ns | XT oscillator | 126 | ||
| External clock in (OSC1) rise or fall time | TosR,TosF | 15 | ns | HS oscillator | 126 | ||
| OSC1↑ (Q2 cycle) to Port input invalid (I/O in hold time), Extended (LF) | TosH2ioI | 200 | ns | Extended (LF) | 127 | ||
| Ambient temperature under bias | -55 | 125 | °C | 121 | |||
| Storage temperature | -65 | 150 | °C | 121 | |||
| Voltage on any pin with respect to VSS (except VDD, MCLR, RA4) | -0.3 | V | Maximum is VDD + 0.3V | 121 | |||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 6.5 | V | 121 | ||
| Voltage on MCLR with respect to VSS | MCLR | 0 | 13.5 | V | Note 2 | 121 | |
| Voltage on RA4 with respect to VSS | RA4 | 0 | 12 | V | 121 | ||
| Total power dissipation | Pdis | 1 | W | Note 1 | 121 | ||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 121 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 121 |
CAD (KiCad official)
- Symbol:
PIC16LF73-I - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
- 3D model files:
pic16lf73-i-etched.step/pic16lf73-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16lf73-i.step/pic16lf73-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (174 pp, sha256
81a107b5141fded6, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Other parts in this family
This page is PIC16LF73-I/SS. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- PIC16LF73-I/SP