3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXC6219A332MR-G
Torex Semicon · Linear Voltage Regulators (LDO) · SOT-25
XC6219A332MR-G from Torex Semicon, in a SOT-25. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input for the regulator; the datasheet specifies an operating input range of 2.0 V to 6.0 V, with an absolute maximum input voltage of 7.0 V, and a 1.0 µF input capacitor is recommended between VIN and VSS. |
| 2 | VSS | power_in | Ground pin to which all voltages are referenced; the output capacitor should be connected as close as possible between VOUT and VSS, and the VIN-VSS wiring resistance should be kept low. |
| 3 | CE | input | ON/OFF control input; for this Type A part it is active high with a built-in pull-down resistor, with a 'High' level of at least 1.6 V and a 'Low' level of at most 0.25 V, and the CE pin voltage must stay within VSS-0.3 V to VIN+0.3 V. |
| 4 | NC | unconnected | No connection; the pin is not internally connected on the SOT-25 package. |
| 5 | VOUT | power_out | Regulated output pin (3.3 V nominal for this MPN, ±2% accuracy); the datasheet recommends an output capacitor of at least 1.0 µF connected close to VOUT and VSS, and the output current is limited to about 50 mA during a short circuit. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Torex Semicon |
| Package | SOT-25 |
| Category | Power Supply Chip |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (2%) at 3.3V nominal | VOUT(E) | 3.234 | 3.3 | 3.366 | V | IOUT=30mA; VOUT(T)=3.30V, 2% grade (VOUT(T)x0.98 to x1.02); Voltage Chart value | 11 |
| Input Voltage | VIN | 2 | 6 | V | 6 | ||
| Maximum Output Current | IOUTMAX | 240 | mA | 1.8V≦VOUT(T)≦5.0V | 6 | ||
| Load Regulation | ΔVOUT | 15 | 50 | mV | 1mA≦IOUT≦100mA | 6 | |
| Supply Current (Type A) | IDD | 28 | 55 | μA | VCE=VIN=VOUT(T)+1.0V | 6 | |
| Stand-by Current | ISTB | 0.01 | 0.1 | μA | VIN=VOUT(T)+1.0V、VCE=VSS | 6 | |
| Line Regulation | ΔVOUT/(ΔVIN・VOUT) | 0.01 | 0.2 | %/V | VOUT(T)+1.0V≦VIN≦6.0V, IOUT=30mA | 6 | |
| Output Voltage Temperature Characteristics | ΔVOUT/(ΔTopr・VOUT) | -100 | 100 | ppm/℃ | IOUT=30mA, -40℃≦Topr≦85℃ | 6 | |
| Current Limiter | Ilim | 240 | 300 | mA | 1.8V≦VOUT(T)≦5.0V, VIN=VOUT(T)+1.0V, VCE=VIN | 6 | |
| CE High Level Voltage | VCEH | 1.6 | V | 6 | |||
| CE Low Level Voltage | VCEL | 0.25 | V | 6 | |||
| CE High Level Current (Type A) | ICEH | -0.1 | 5 | μA | VIN=VCE=VOUT(T)+1.0V | 6 | |
| Input Voltage (absolute maximum) | VIN | 7 | V | 5 | |||
| Power Dissipation SOT-25, IC only | Pd | 250 | mW | Ta=25℃, IC only | 5 | ||
| Power Dissipation SOT-25, 40mm x 40mm standard board | Pd | 600 | mW | Ta=25℃, PCB mounted, reference only | 5 | ||
| Power Dissipation SOT-25, JESD51-7 board | Pd | 760 | mW | Ta=25℃, PCB mounted, reference only | 5 | ||
| Operating Ambient Temperature | Topr | -40 | 85 | ℃ | 5 | ||
| Storage Temperature | Tstg | -55 | 125 | ℃ | 5 | ||
| Output Capacitor (CL) recommended | CL | 1 | μF | Recommended output capacitor, placed close to VOUT and VSS; ceramic compatible | 14 |
CAD (KiCad official)
- Symbol:
XC6219A332MR-G - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-25 (KiCad packages3D, STEP)
- 3D model files:
xc6219a332mr-g-etched.step/xc6219a332mr-g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xc6219a332mr-g.step/xc6219a332mr-g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Torex Semicon datasheet (27 pp, sha256
cb6c2d5a73297396, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).