3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM5155DSST
Texas Instruments · DC-DC Controllers · WSON-12-EP(2x3)
LM5155DSST from Texas Instruments, in a WSON-12-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BIAS | power_in | Supply voltage input to the VCC regulator, which should be bypassed with a capacitor to PGND; the datasheet allows BIAS up to 45 V (50 V absolute maximum). |
| 2 | VCC | power_out | Output of the internal VCC regulator and supply input of the MOSFET driver, which requires a ceramic bypass capacitor to PGND and is limited to 18 V (absolute maximum). |
| 3 | GATE | output | N-channel MOSFET gate drive output, to be connected directly to the MOSFET gate through a short, low-inductance path, with 1.5-A peak drive capability. |
| 4 | PGND | power_in | Power ground pin, to be connected directly to the sense resistor ground through a low-inductance, wide, and short path. |
| 5 | CS | input | Current sense input, connected to the positive side of the current sense resistor through a short path; DC range is -0.3 V to 0.3 V to AGND. |
| 6 | COMP | output | Output of the internal transconductance error amplifier, with loop compensation components connected between this pin and PGND. |
| 7 | AGND | power_in | Analog ground pin, to be connected to the analog ground plane through a wide and short path. |
| 8 | FB | input | Inverting input of the error amplifier, fed by a voltage divider from the output in boost/SEPIC topologies with the low-side resistor returned to AGND; absolute maximum 3.8 V to AGND. |
| 9 | SS | input | Soft-start time programming pin, where an external capacitor with an internal current source sets the error amplifier reference ramp rate, with the capacitor returned to AGND. |
| 10 | RT | input | Switching frequency setting pin, programmed by a single resistor between RT and AGND to set frequencies from 100 kHz to 2.2 MHz. |
| 11 | PGOOD | output | Open-drain power-good indicator that goes low when FB is below the undervoltage threshold, requiring a pullup resistor to the system rail; absolute maximum 18 V to AGND. |
| 12 | UVLO/EN/SYNC | input | Undervoltage lockout programming pin, set by a resistor divider from the supply, which also accepts a negative pulse for clock synchronization, must not be left floating, and should be connected to BIAS if unused. |
| 13 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-12-EP(2x3) |
| Category | Power Supply Chip |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| BIAS to AGND | -0.3 | 50 | V | 5 | |||
| UVLO to AGND | -0.3 | V | max VBIAS+0.3 V | 5 | |||
| SS to AGND | -0.3 | 3.8 | V | pin not specified to have external voltage applied | 5 | ||
| RT to AGND | -0.3 | 3.8 | V | pin not specified to have external voltage applied | 5 | ||
| FB to AGND | -0.3 | 3.8 | V | 5 | |||
| CS to AGND | -0.3 | 0.3 | V | DC | 5 | ||
| CS to AGND | -1 | V | 100ns transient | 5 | |||
| CS to AGND | -2 | V | 20ns transient | 5 | |||
| PGND to AGND | -0.3 | 0.3 | V | 5 | |||
| VCC to AGND | -0.3 | 18 | V | 18 V or VBIAS + 0.3 V whichever is lower | 5 | ||
| GATE to AGND | -1 | V | 100ns transient | 5 | |||
| GATE to AGND | -2 | V | 50ns transient | 5 | |||
| PGOOD to AGND | -0.3 | 18 | V | 5 | |||
| COMP to AGND | -0.3 | V | 5 | ||||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| Bias input | VBIAS | 2.97 | 45 | V | 2.97 V to 16 V when VCC is connected to BIAS; 3.5 V to 45 V when VCC is supplied from internal regulator | 6 | |
| VCC voltage | VVCC | 2.97 | 16 | V | pin voltage should be less than VBIAS + 0.3 V | 6 | |
| UVLO input | VUVLO | 0 | 45 | V | 6 | ||
| FB input | VFB | 0 | 3.7 | V | 6 | ||
| Typical switching frequency | fSW | 100 | 2200 | kHz | 6 | ||
| Synchronization pulse frequency | fSYNC | 100 | 2200 | kHz | 6 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 6 | ||
| BIAS shutdown current | ISHUTDOWN(BIAS) | 2.6 | 5 | uA | VBIAS = 12 V, VUVLO = 0 V | 6 | |
| BIAS operating current | IOPERATING(BIAS) | 480 | 540 | uA | VBIAS = 12 V, VUVLO = 2 V, VFB = VREF, RT = 220 kΩ | 6 | |
| VCC regulation | VVCC-REG | 6.5 | 6.85 | 7 | V | VBIAS = 8 V, No load | 6 |
| VCC regulation | 6.5 | V | VBIAS = 8 V, IVCC = 35 mA | 6 | |||
| VCC UVLO threshold | VVCC-UVLO(RISING) | 2.75 | 2.85 | 2.95 | V | VCC rising | 6 |
| VCC UVLO hysteresis | 0.063 | V | VCC falling | 6 | |||
| VCC sourcing current limit | IVCC-CL | 35 | 105 | mA | VBIAS = 10 V, VVCC = 0 V | 6 | |
| Enable threshold | VEN(RISING) | 0.4 | 0.52 | 0.7 | V | EN rising | 6 |
| Enable threshold | VEN(FALLING) | 0.33 | 0.49 | 0.63 | V | EN falling | 6 |
| Enable hysteresis | VEN(HYS) | 0.03 | V | EN falling | 7 | ||
| UVLO / SYNC threshold | VUVLO(RISING) | 1.425 | 1.5 | 1.575 | V | UVLO rising | 7 |
| UVLO / SYNC threshold | VUVLO(FALLING) | 1.37 | 1.45 | 1.52 | V | UVLO falling | 7 |
| UVLO / SYNC threshold hysteresis | VUVLO(HYS) | 0.05 | V | UVLO falling | 7 | ||
| UVLO hysteresis current | IUVLO | 4 | 5 | 6 | uA | VUVLO = 1.6 V | 7 |
| Soft-start current | ISS | 9 | 10 | 11 | uA | 7 | |
| SS pull-down switch RDSON | 55 | Ω | 7 | ||||
| Switching frequency | fsw1 | 85 | 100 | 115 | kHz | RT = 220 kΩ | 7 |
| Switching frequency | fsw2 | 1980 | 2200 | 2420 | kHz | RT = 9.09 kΩ | 7 |
| Minimum on-time | tON(MIN) | 50 | ns | RT = 9.09 kΩ | 7 | ||
| Maximum duty cycle limit | DMAX1 | 80 | 85 | 90 | % | RT = 9.09 kΩ | 7 |
| Maximum duty cycle limit | DMAX2 | 90 | 93 | 96 | % | RT = 220 kΩ | 7 |
| Peak slope compensation current | ISLOPE | 22.5 | 30 | 37.5 | uA | RT = 220 kΩ | 7 |
| Current Limit threshold (CS-PGND) | VCLTH | 93 | 100 | 107 | mV | 7 | |
| FB reference | VREF | 0.99 | 1 | 1.01 | V | LM5155, LM51551 | 7 |
| Transconductance | Gm | 2 | mA/V | 7 | |||
| COMP sourcing current | 180 | uA | VCOMP = 1.2 V | 7 | |||
| COMP clamp voltage | 2.5 | 2.8 | V | COMP rising (VUVLO = 2.0V) | 7 | ||
| COMP clamp voltage | 1 | 1.1 | V | COMP falling | 7 | ||
| Over-voltage threshold | VOVTH | 107 | 110 | 113 | % | FB rising (reference to VREF) | 7 |
| Over-voltage threshold | VOVTH | 105 | % | FB falling (reference to VREF) | 7 | ||
| PGOOD pull-down switch RDSON | 90 | Ω | 1 mA sinking | 7 | |||
| Undervoltage threshold | VUVTH | 87 | 90 | 93 | % | FB falling (reference to VREF) | 7 |
| Undervoltage threshold | VUVTH | 95 | % | FB rising (reference to VREF) | 7 | ||
| MOSFET driver high-state voltage drop | 0.25 | V | 100 mA sinking | 7 | |||
| MOSFET driver low-state voltage drop | 0.15 | V | 100 mA sourcing | 7 | |||
| Thermal shutdown threshold | TTSD | 175 | °C | Temperature rising | 7 | ||
| Thermal shutdown hysteresis | 15 | °C | 7 | ||||
| Junction-to-ambient thermal resistance | RθJA | 63.7 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 61 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 32.1 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 2.3 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 31.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 11.2 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM5155DSST - Footprint:
Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65 - 3D model: WSON-12-EP(2x3) (KiCad packages3D, STEP)
- 3D model files:
lm5155dsst-etched.step/lm5155dsst-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5155dsst.step/lm5155dsst.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
e65e47f61e64e3c3, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).