Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8609AHMSE16#PBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8609AHMSE16#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST power_out Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not put a resistor in series with this pin.
2 NC unconnected No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it.
3 SW power_out Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB for good performance.
4 NC unconnected No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it.
5 INTVCC power_out Internal 3.5V regulator bypass pin that varies between 2.8V and 3.5V, supplies at most 20mA, must be decoupled to power ground with at least 1µF low-ESR ceramic, and must not be loaded with external circuitry.
6 RT passive A resistor tied between RT and ground sets the switching frequency.
7 SYNC input External clock synchronization input: ground for low-ripple Burst Mode operation, tie to a clock for synchronization, float for pulse-skipping mode without spread spectrum, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum.
8 GND power_in Ground pin as read from the 16-lead pin layout; the datasheet states GND as the exposed pad (pin 17), so this assignment needs confirmation against the package drawing.
9 FB input Feedback pin that the adjustable-output parts regulate to 0.782V; connect the feedback resistor divider tap to this pin.
10 FB input The layout lists FB twice on the right-hand side of the 16-lead pin configuration; this pin is taken as the feedback pin (0.782V regulation) but its assignment needs confirmation.
11 TR/SS input Output tracking and soft-start pin: a voltage below 0.782V forces FB to follow it, and a capacitor sets the start-up ramp via an internal 2µA pull-up from INTVCC; the pin is pulled to ground through 300Ω during shutdown and fault conditions.
12 PG output Open-drain power-good output that stays low until FB is within ±8.5% of the regulation voltage (±7.5% for fixed-output parts) with no faults, and is valid when VIN is above 3.2V.
13 NC unconnected No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it.
14 VIN power_in Supplies the internal circuitry and the internal topside power switch; it must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins.
15 NC unconnected No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it.
16 EN/UV input Enable and undervoltage input: the part shuts down when low and is active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused.
17 GND power_in Exposed pad is GND and must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage VIN(MIN) 2.7 3 3.2 V 4
VIN Quiescent Current (shutdown) IQ 1 4 µA VEN/UV = 0V, VSYNC = 0V 4
VIN Quiescent Current (not switching) IQ 1.7 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V; full temperature range 4
VIN Current in Regulation IIN 46 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100µA 4
VIN Current in Regulation IIN 480 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA; full temperature range 4
Feedback Reference Voltage (E/I/H grade) VFB 0.778 0.782 0.786 V VIN = 6V, ILOAD = 100mA 4
Feedback Reference Voltage (E/I/H grade) VFB 0.77 0.782 0.794 V VIN = 6V, ILOAD = 100mA; full temperature range 4
Feedback Pin Input Current IFB -20 20 nA VFB = 1.0V; full temperature range 4
Feedback Voltage Line Regulation 0.004 0.02 %/V VIN = 4.0V to 40V; full temperature range 4
Minimum On-Time tON(MIN) 45 75 ns ILOAD = 1.5A, SYNC = 0V; full temperature range 4
Minimum On-Time tON(MIN) 45 60 ns ILOAD = 1.5A, SYNC = 1.9V; full temperature range 4
Minimum Off Time tOFF(MIN) 90 130 ns 4
Oscillator Frequency fSW 155 200 245 kHz RT = 221k, ILOAD = 0.5A; full temperature range 5
Oscillator Frequency fSW 640 700 760 kHz RT = 60.4k, ILOAD = 0.5A; full temperature range 5
Oscillator Frequency fSW 1.925 2 2.075 MHz RT = 18.2k, ILOAD = 0.5A; full temperature range 5
Top Power NMOS Current Limit ILIM 3.4 4.5 5.7 A full temperature range 5
SW Leakage Current ISW 15 µA VIN = 42V, VSW = 40V; full temperature range 5
EN/UV Pin Threshold VEN/UV 0.99 1.05 1.11 V EN/UV Rising; full temperature range 5
EN/UV Pin Current IEN/UV -20 20 nA VEN/UV = 2V; full temperature range 5
PG Upper Threshold Offset from VFB 5 8.5 13 % VFB Rising; full temperature range 5
PG Lower Threshold Offset from VFB 5 8.5 13 % VFB Falling; full temperature range 5
PG Leakage IPG -200 200 nA VPG = 42V; full temperature range 5
PG Pull-Down Resistance RPG 550 1200 Ω VPG = 0.1V 5
Sync Low Input Voltage VSYNC(LOW) 0.4 0.9 V full temperature range 5
Sync High Input Voltage VSYNC(HIGH) 2.7 3.2 V INTVCC = 3.5V; full temperature range 5
TR/SS Source Current ITR/SS 1 2 3 µA full temperature range 5
TR/SS Pull-Down Resistance RTR/SS 300 900 Ω Fault Condition, TR/SS = 0.1V 5
Spread Spectrum Modulation Frequency fSS 1 3 6 kHz VSYNC = 3.3V 5
Top Power NMOS On-Resistance RDS(ON) 185 mΩ ILOAD = 1A 5
Bottom Power NMOS On-Resistance RDS(ON) 115 mΩ 5
EN/UV Pin Hysteresis 50 mV 5
PG Hysteresis 0.5 % 5
FB, TR/SS pin voltage VFB, VTR/SS 4 V Absolute maximum rating (Note 1) 2
SYNC, VOUT pin voltage VSYNC, VOUT 6 V Absolute maximum rating (Note 1) 2
Storage Temperature Range TSTG -65 150 °C 2
Operating Junction Temperature Range (LT8609AH) TJ -40 150 °C LT8609AH ordering grade 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W 16-Lead MSOP (MS package) 2
Thermal Resistance Junction-to-Case (Pad) θJC(PAD) 10 °C/W 16-Lead MSOP (MS package) 2

CAD (KiCad official)

  • Symbol: LT8609AHMSE16#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8609ahmse16-pbf-etched.step / lt8609ahmse16-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8609ahmse16-pbf.step / lt8609ahmse16-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 bb514bf594e97238, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF