3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS92661QPHPRQ1
Texas Instruments · LED Drivers · TQFP-48(7x7)
TPS92661QPHPRQ1 from Texas Instruments, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CPP | power_out | Charge pump output that must be bypassed to LED12 with a ceramic capacitor of at least 0.1 µF, and it supplies the gate drive for the internal floating switches (CPP to GND rated -0.3 V to 67 V). |
| 2 | NC | unconnected | No connection. |
| 3 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 4 | EN | input | Active-high enable; the device is in reset when EN is low, and it may be tied to VCC or VIN for enable at power-up (VIH 1.9 V min, VIL 0.8 V max). |
| 5 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 6 | SYNC | bidirectional | Synchronization pin that resets the internal PWM counter when driven high and may be left unconnected, since it is internally pulled down; only one device should drive it. |
| 7 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 8 | CLK | input | Externally provided primary system clock for the UART and PWM hardware, rated up to 16 MHz with a 40% to 60% duty cycle. |
| 9 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 10 | TX | bidirectional | UART transmit output (tri-state) that requires a 100 kΩ pull-up resistor to avoid false start conditions at the microcontroller. |
| 11 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 12 | RX | bidirectional | UART receive input, a feed-through pin that operates at CLK/16 bit rate and connects to the MCU TX output and the next device's RX pin. |
| 13 | VCC | power_out | Output of the on-board 3.3 V LDO that requires a ceramic output capacitor of 0.1 µF or greater; tie to VIN for 5 V microcontroller systems. |
| 14 | VIN | power_in | 5 V primary power supply input (4.5 V to 5.5 V) that should be bypassed with a ceramic capacitor of at least 0.1 µF. |
| 15 | ADR1 | input | Second bit of the device address, to be tied to VIN or GND. |
| 16 | ADR2 | input | Most significant bit of the device address, to be tied to VIN or GND. |
| 17 | NC | unconnected | No connection. |
| 18 | NC | unconnected | No connection. |
| 19 | NC | unconnected | No connection. |
| 20 | NC | unconnected | No connection. |
| 21 | NC | unconnected | No connection. |
| 22 | ADR0 | input | Least significant bit of the device address, to be tied to VIN or GND. |
| 23 | VIN | power_in | 5 V primary power supply input (4.5 V to 5.5 V) that should be bypassed with a ceramic capacitor of at least 0.1 µF. |
| 24 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 25 | RX | bidirectional | UART receive input, a feed-through pin that operates at CLK/16 bit rate and connects to the MCU TX output and the next device's RX pin. |
| 26 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 27 | TX | bidirectional | UART transmit output (tri-state) that requires a 100 kΩ pull-up resistor to avoid false start conditions at the microcontroller. |
| 28 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 29 | CLK | input | Externally provided primary system clock for the UART and PWM hardware, rated up to 16 MHz with a 40% to 60% duty cycle. |
| 30 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 31 | SYNC | bidirectional | Synchronization pin that resets the internal PWM counter when driven high and may be left unconnected, since it is internally pulled down; only one device should drive it. |
| 32 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 33 | EN | input | Active-high enable; the device is in reset when EN is low, and it may be tied to VCC or VIN for enable at power-up (VIH 1.9 V min, VIL 0.8 V max). |
| 34 | GND | power_in | Device system ground; all GND pins must be tied to system ground for proper operation. |
| 35 | NC | unconnected | No connection. |
| 36 | LED0 | output | LED bypass switch output connected to the cathode of LED1 (LEDx to GND rated -0.3 V to 60 V). |
| 37 | LED1 | output | LED bypass switch output connected to the anode of LED1 and the cathode of LED2 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 38 | LED2 | output | LED bypass switch output connected to the anode of LED2 and the cathode of LED3 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 39 | LED3 | output | LED bypass switch output connected to the anode of LED3 and the cathode of LED4 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 40 | LED4 | output | LED bypass switch output connected to the anode of LED4 and the cathode of LED5 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 41 | LED5 | output | LED bypass switch output connected to the anode of LED5 and the cathode of LED6 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 42 | LED6 | output | LED bypass switch output connected to the anode of LED6 and the cathode of LED7 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 43 | LED7 | output | LED bypass switch output connected to the anode of LED7 and the cathode of LED8 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 44 | LED8 | output | LED bypass switch output connected to the anode of LED8 and the cathode of LED9 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 45 | LED9 | output | LED bypass switch output connected to the anode of LED9 and the cathode of LED10 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 46 | LED10 | output | LED bypass switch output connected to the anode of LED10 and the cathode of LED11 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 47 | LED11 | output | LED bypass switch output connected to the anode of LED11 and the cathode of LED12 (LEDx to LED(x-1) rated -0.3 V to 7 V). |
| 48 | LED12 | output | LED bypass switch output connected to the anode of LED12 (LEDx to GND rated -0.3 V to 60 V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-48(7x7) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage, VIN and VCC to GND | VIN, VCC | -0.3 | 7 | V | 4 | ||
| Input voltage, CPP to GND | -0.3 | 67 | V | 4 | |||
| Input voltage, CPP to LED12 | -0.3 | 7 | V | 4 | |||
| Input voltage, LEDx to GND | -0.3 | 60 | V | 4 | |||
| Input voltage, LEDx to LED(x-1) | -0.3 | 7 | V | 4 | |||
| Input voltage, SYNC, EN, CLK, TX, RX, ADR0-2 to GND | -0.3 | 7 | V | 4 | |||
| Storage temperature range | Tstg | -40 | 150 | °C | 4 | ||
| Electrostatic discharge, human body model (HBM) | V(ESD) | -2000 | 2000 | V | Per AEC Q100-002 | 5 | |
| Electrostatic discharge, charged device model (CDM), all pins | V(ESD) | -750 | 750 | V | Per AEC Q100-011 | 5 | |
| VIN supply input voltage range | VIN | 4.5 | 5.5 | V | 5 | ||
| Input voltage range per channel | VI | 5 | V | LEDx to LED(x-1) | 5 | ||
| Output current range, continuous | IO | 2 | A | LEDx to LED(x-1), continuous | 5 | ||
| Output current range, pulsed | IO | 4 | A | LEDx to LED(x-1), pulsed, 1-ms duration | 5 | ||
| CLK frequency | fCLK | 0.1 | 16 | MHz | Minimum applies only when CKWEN bit is set; as low as 0 Hz possible when not set | 5 | |
| CLK duty cycle | DCLK | 40 | 60 | % | 5 | ||
| EN input pulse width low | tEW | 50 | ns | 5 | |||
| High-level input voltage | VIH | 1.9 | V | 5 | |||
| Low-level input voltage | VIL | 0.8 | V | 5 | |||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Regulated VCC voltage | VCC-REG | 3.1 | 3.3 | 3.5 | V | 0 mA ≤ IVCC ≤ 5 mA | 6 |
| VCC current limit | IVCC-LIM | 10 | mA | 6 | |||
| Input operating bias current | IVIN-OP | 1 | mA | No switching | 6 | ||
| VIN internal POR threshold | VIN-UVT | 4.5 | V | VIN rising | 6 | ||
| Charge pump operating voltage | VCPP | 6.2 | V | VVIN = 5 V, 0 V ≤ VSW ≤ -60 V | 6 | ||
| Charge pump oscillator frequency | fCPP | 1.3 | 2.3 | 3.3 | MHz | 6 | |
| LED switch on-resistance (single channel) | RDS(on) | 225 | mΩ | Single channel; includes internal bond wires (footnote 1) | 6 | ||
| All switches on-resistance | RALL(on) | 1800 | 3400 | mΩ | Measured LED12 - LED0 | 6 | |
| OFF state switch leakage current | IDS(off) | 50 | µA | 6 | |||
| LED short threshold voltage | VTH-S | 0.52 | 1.4 | V | 0 V ≤ VSW ≤ -60 V | 6 | |
| LED open threshold voltage | VTH-O | 5 | 6 | 6.9 | V | 0 V ≤ VSW ≤ -60 V | 6 |
| LED open detection and correction delay | tTO-O | 50 | 150 | ns | 6 | ||
| LED fault reporting delay | tREP | 5 | µs | 6 | |||
| LEDx drain voltage rise time | tRISE(LEDx) | 2 | µs | ILED = 800 mA; specified by design, not production tested | 6 | ||
| LEDx drain voltage fall time | tFALL(LEDx) | 2 | µs | ILED = 800 mA; specified by design, not production tested | 6 | ||
| High-level input voltage threshold | VIH-TH | 1.9 | V | 6 | |||
| Low-level input voltage threshold | VIL-TH | 0.8 | V | 6 | |||
| High-level output voltage | VOH | 4.27 | V | ISOURCE = 2 mA, VVCC = 4.0 V | 6 | ||
| Low-level output voltage | VOL | 0.23 | V | ISINK = 2 mA, VVCC = 4.5 V | 6 | ||
| Output short circuit current (source or sink) | IOS | 42 | mA | VVCC = 4.5 V | 6 | ||
| Internal SYNC pull-down | RSP | 100 | kΩ | 6 | |||
| CLK rise to TX output valid | tTO | 80 | ns | Specified by design, not production tested | 6 | ||
| CLK rise to TX output tri-state | tTZ | 80 | ns | Specified by design, not production tested | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 25.7 | °C/W | TQFP (PHP) 48 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 10.5 | °C/W | TQFP (PHP) 48 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 6.1 | °C/W | TQFP (PHP) 48 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 0.2 | °C/W | TQFP (PHP) 48 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 6 | °C/W | TQFP (PHP) 48 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 0.3 | °C/W | TQFP (PHP) 48 pins | 5 |
CAD (KiCad official)
- Symbol:
TPS92661QPHPRQ1 - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
tps92661qphprq1-etched.step/tps92661qphprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps92661qphprq1.step/tps92661qphprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (53 pp, sha256
01209eeb0a7e6f85, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).