Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SN65LVDS180DR

Texas Instruments · LVDS ICs · SOIC-14

SN65LVDS180DR from Texas Instruments, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No internal connection; the datasheet recommends grounding NC pins at the board level for optimum thermal performance.
2 R output LVTTL receiver output that is high for VID ≥ 100 mV and low for VID ≤ -100 mV, with VOH of at least 2.4 V at IOH = -8 mA and VOL of at most 0.4 V at IOL = 8 mA, and it goes high-impedance when RE/ is high.
3 RE input Active-low receiver enable (printed RE/); when it is high the receiver output R is placed in the high-impedance state.
4 DE input Driver enable input; when it is low the driver outputs Y and Z are turned off (no output) and the driver input is disconnected.
5 D input LVTTL driver data input with VIH of at least 2 V and VIL of at most 0.8 V, tolerant of input signals up to 5 V, where an open input drives a low output.
6 GND power_in Ground reference for the device, to be connected with a short, low-impedance path to the PCB ground plane to reduce ground bounce.
7 GND power_in Ground reference for the device, to be connected with a short, low-impedance path to the PCB ground plane to reduce ground bounce.
8 NC unconnected No internal connection; the datasheet recommends grounding NC pins at the board level for optimum thermal performance.
9 Y output Differential LVDS non-inverting driver output with
10 Z output Differential LVDS inverting driver output with
11 B input Differential LVDS inverting receiver input; the receiver switches at VIT+ and VIT- of ±100 mV and is specified for a differential input magnitude of 0.05 V to 0.6 V.
12 A input Differential LVDS non-inverting receiver input; the receiver switches at VIT+ and VIT- of ±100 mV and is specified for a differential input magnitude of 0.05 V to 0.6 V.
13 VCC power_in Supply voltage, 3.0 V minimum, 3.3 V nominal and 3.6 V maximum, with an absolute maximum of 4 V.
14 VCC power_in Supply voltage, 3.0 V minimum, 3.3 V nominal and 3.6 V maximum, with an absolute maximum of 4 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-14
Category Interface
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC -0.5 4 V 6
Voltage range, D, R, DE, RE -0.5 6 V 6
Voltage range, Y, Z, A, B -0.5 4 V 6
Differential output voltage /VOD/ 1 V 6
Storage temperature Tstg -65 150 °C 6
Lead temperature 250 °C 1.6 mm (1/16 inch) from case for 10 seconds 6
ESD, bus pins Y, Z, A, B and GND, Class 3, A V(ESD) -12000 12000 V Y, Z, A, B, and GND; Class 3, A 6
ESD, bus pins Y, Z, A, B and GND, Class 3, B V(ESD) -600 600 V Y, Z, A, B, and GND; Class 3, B 6
ESD, all pins, Class 3, A V(ESD) -7000 7000 V All pins; Class 3, A 6
ESD, all pins, Class 3, B V(ESD) -500 500 V All pins; Class 3, B 6
Supply voltage VCC 3 3.3 3.6 V 7
High-level input voltage VIH 2 V 7
Low-level input voltage VIL 0.8 V 7
Magnitude of differential input voltage /VID/ 0.05 0.6 V 7
Magnitude of differential output voltage with disabled driver /VOD(dis)/ 520 mV 7
Driver output voltage VOY or VOZ 0 2.4 V 7
Operating free-air temperature TA -40 85 °C 7
Power rating 987 mW TA ≤ 25°C; SOIC D, 14 pins 7
Power rating 513 mW TA = 85°C; SOIC D, 14 pins 7
Supply current, driver and receiver enabled ICC 9 12 mA Driver and receiver enabled, no receiver load, driver RL = 100 Ω 7
Supply current, driver enabled, receiver disabled ICC 5 7 mA Driver enabled, receiver disabled, RL = 100 Ω 7
Supply current, driver disabled, receiver enabled ICC 1.5 2 mA Driver disabled, receiver enabled, no load 7
Supply current, disabled ICC 0.5 1 mA Disabled 7
Differential output voltage magnitude /VOD/ 247 340 454 mV RL = 100 Ω, See Figure 11 and Figure 12 8
Change in differential output voltage magnitude between logic states Δ/VOD/ -50 50 mV 8
Steady-state common-mode output voltage VOC(SS) 1.125 1.2 1.375 V See Figure 12 8
Change in steady-state common-mode output voltage between logic states ΔVOC(SS) -50 50 mV 8
Peak-to-peak common-mode output voltage VOC(PP) 50 150 mV 8
High-level input current, DE IIH -0.5 -20 µA VIH = 5 V 8
High-level input current, D IIH 2 20 µA VIH = 5 V 8
Low-level input current, DE IIL -0.5 -10 µA VIL = 0.8 V 8
Low-level input current, D IIL 2 10 µA VIL = 0.8 V 8
Short-circuit output current IOS 3 10 mA VOY or VOZ = 0 V 8
Off-state output current IO(OFF) -1 1 µA DE = 0 V, VOY = VOZ = 0 V; DE = VCC, VCC < 1.5 V, VOY = VOZ = 0 V 8
Positive-going differential input voltage threshold VIT+ 100 mV See Figure 14 and Table 2 8
Negative-going differential input voltage threshold VIT- -100 mV See Figure 14 and Table 2 8
High-level output voltage VOH 2.4 V IOH = -8 mA 8
High-level output voltage VOH 2.8 V IOH = -4 mA 8
Low-level output voltage VOL 0.4 V IOL = 8 mA 8
Input current (A or B input) II -2 -11 -20 µA VI = 0 V 8
Input current (A or B input) II -1.2 -3 µA VI = 2.4 V 8
Power-off input current (A or B input) II(OFF) -20 20 µA VCC = 0 V 8
High-level input current (enables) IIH -10 10 µA VIH = 5 V 8
Low-level input current (enables) IIL -10 10 µA VIL = 0.8 V 8
High-impedance output current IOZ -10 10 µA VO = 0 or 5 V 8
Propagation delay time, low-to-high-level output (driver) tPLH 1.7 2.7 ns RL = 100 Ω, CL = 10 pF, See Figure 11 9
Propagation delay time, high-to-low-level output (driver) tPHL 1.7 2.7 ns RL = 100 Ω, CL = 10 pF, See Figure 11 9
Differential output signal rise time tr 0.8 1 ns 9
Differential output signal fall time tf 0.8 1 ns 9
Pulse skew (/tpHL, tpLH/) tsk(p) 300 ps 9
Channel-to-channel output skew tsk(o) 150 ps 9
Enable time ten 4.3 10 ns See Figure 13 9
Disable time tdis 3.1 10 ns 9
Propagation delay time, low-to-high-level output (receiver) tPLH 3.7 4.5 ns CL = 10 pF, See Figure 15 9
Propagation delay time, high-to-low-level output (receiver) tPHL 3.7 4.5 ns CL = 10 pF, See Figure 15 9
Pulse skew (/tpHL, tpLH/) (receiver) tsk(p) 0.3 ns 9
Output signal rise time (receiver) tr 0.7 1.5 ns 9
Output signal fall time (receiver) tf 0.9 1.5 ns 9
Propagation delay time, high-impedance-to-high-level output tPZH 2.5 ns See Figure 16 9

CAD (KiCad official)

  • Symbol: SN65LVDS180DR
  • Footprint: Package_SO:SOIC-14_3.9x8.7mm_P1.27mm
  • 3D model: SOIC-14 (KiCad packages3D, STEP)
  • 3D model files: sn65lvds180dr-etched.step / sn65lvds180dr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sn65lvds180dr.step / sn65lvds180dr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (56 pp, sha256 69be50e0c02c6e8a, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF