by John Lauer
An independently designed 12 V to 5 V, 1 A synchronous buck molecule (TI TPS54202), with calculations, ngspice and PSpice simulation, KiCad 10 schematic and board, and the board laid out and analysed with adom-aiflow.
main
John Lauer
JLCPCB build: the JLCPCB BOM (LCSC numbers, fit=post for contacts) and the proof behind every part swap
16d0d50
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990
{
"ref": "L1",
"original": "AMPLH5030S-150MT",
"candidate": "HCMA-0530-150-M",
"lcsc": "C49190153",
"verdict": "PASS",
"checks": [
{
"check": "L_uH",
"pass": true,
"detail": "15 vs 15 (original +/-20 %)",
"info": false
},
{
"check": "tolerance",
"pass": true,
"detail": "20 % vs 20 %",
"info": false
},
{
"check": "isat_A",
"pass": false,
"detail": "3.0 vs original 3.7 (the design limit below decides)",
"info": true
},
{
"check": "irms_A",
"pass": false,
"detail": "2.5 vs original 3.5 (the design limit below decides)",
"info": true
},
{
"check": "dcr_mohm_max",
"pass": false,
"detail": "165 vs original 118 (the design limit below decides)",
"info": true
},
{
"check": "temperature range",
"pass": true,
"detail": "[-55, 125] covers [-55, 125]",
"info": false
},
{
"check": "height",
"pass": true,
"detail": "2.8 mm vs 2.8 mm",
"info": false
},
{
"check": "design: isat_A >= 2.5",
"pass": true,
"detail": "3.0 (from calcs.json inductor.Isat_required_A (TPS54202 high-side current limit, min))",
"info": false
},
{
"check": "design: irms_A >= 1.009",
"pass": true,
"detail": "2.5 (from calcs.json inductor.Irms_A)",
"info": false
},
{
"check": "design: dcr_mohm_max <= 200",
"pass": true,
"detail": "165 (from loss budget: 1.009 A rms squared x 200 mOhm = 0.20 W, about 2 % of the 10 W output; Idc 2.5 A (40 C rise) leaves the part at about 6 C rise at 1 A)",
"info": false
},
{
"check": "land fit pad 1",
"pass": true,
"detail": "100 % of the terminal on pad 1 (2.15 x 3.50 at -2.17, 0.00)",
"info": false
},
{
"check": "land fit pad 2",
"pass": true,
"detail": "100 % of the terminal on pad 2 (2.15 x 3.50 at 2.17, 0.00)",
"info": false
},
{
"check": "original not on LCSC",
"pass": true,
"detail": "searched AMPLH5030S-150MT, AMPLH5030S150MT, AMPLH5030S on 2026-10-05: not found",
"info": false
}
],
"checkedAt": "2026-10-05T14:07:20+00:00",
"facts": "design/swaps/L1.json",
"notes": "Abracon AMPLH5030S is not stocked at JLCPCB/LCSC. Same 15 uH, same 2.8 mm height, molded, shielded, 5.4 x 5.2 mm body whose 1.5 x 2.2 mm terminals land inside the existing 2.15 x 3.5 mm pads. Weaker than the Abracon (Isat 3.0 vs 3.7 A, DCR 165 vs 118 mOhm max) but inside every limit the design sets."
}