main
John Lauer JLCPCB build: the JLCPCB BOM (LCSC numbers, fit=post for contacts) and the proof behind every part swap 16d0d50
{
 "ref": "L1",
 "kind": "inductor",
 "profile": "jlcpcb",
 "original": {
  "mpn": "AMPLH5030S-150MT",
  "manufacturer": "Abracon",
  "datasheet": "Abracon AMPLH5030S datasheet p2 (electrical), p3 (dimensions)",
  "params": {
   "L_uH": 15,
   "tol_pct": 20,
   "isat_A": 3.7,
   "irms_A": 3.5,
   "dcr_mohm_max": 118,
   "temp_C": [
    -55,
    125
   ]
  },
  "body_mm": {
   "L": 5.6,
   "W": 5.2,
   "H": 2.8
  },
  "lcscSearch": {
   "queries": [
    "AMPLH5030S-150MT",
    "AMPLH5030S150MT",
    "AMPLH5030S"
   ],
   "found": false,
   "checked": "2026-10-05"
  }
 },
 "candidate": {
  "mpn": "HCMA-0530-150-M",
  "manufacturer": "YOUCHI",
  "lcsc": "C49190153",
  "stock": 1670,
  "stockChecked": "2026-10-05",
  "datasheet": "https://www.lcsc.com/datasheet/C49190153.pdf (YOUCHI HCMA-0530-XXX-M spec, p2 table, p3 dimensions)",
  "params": {
   "L_uH": 15,
   "tol_pct": 20,
   "isat_A": 3.0,
   "irms_A": 2.5,
   "dcr_mohm_max": 165,
   "temp_C": [
    -55,
    125
   ]
  },
  "body_mm": {
   "L": 5.4,
   "W": 5.2,
   "H": 2.8
  },
  "terminals": [
   {
    "pad": "1",
    "x": -1.95,
    "y": 0,
    "w": 1.5,
    "h": 2.2
   },
   {
    "pad": "2",
    "x": 1.95,
    "y": 0,
    "w": 1.5,
    "h": 2.2
   }
  ]
 },
 "requires": {
  "isat_A": [
   ">=",
   2.5,
   "calcs.json inductor.Isat_required_A (TPS54202 high-side current limit, min)"
  ],
  "irms_A": [
   ">=",
   1.009,
   "calcs.json inductor.Irms_A"
  ],
  "dcr_mohm_max": [
   "<=",
   200,
   "loss budget: 1.009 A rms squared x 200 mOhm = 0.20 W, about 2 % of the 10 W output; Idc 2.5 A (40 C rise) leaves the part at about 6 C rise at 1 A"
  ]
 },
 "notes": "Abracon AMPLH5030S is not stocked at JLCPCB/LCSC. Same 15 uH, same 2.8 mm height, molded, shielded, 5.4 x 5.2 mm body whose 1.5 x 2.2 mm terminals land inside the existing 2.15 x 3.5 mm pads. Weaker than the Abracon (Isat 3.0 vs 3.7 A, DCR 165 vs 118 mOhm max) but inside every limit the design sets."
}