AMPLH5030S-150MT

{
 "schema": "adom/mark-plan@1",
 "mpn": "AMPLH5030S-150MT",
 "step": "/home/adom/project/basic-parts-overhaul/pages-extra/amplh5030s-150mt/AMPLH5030S-150MT.step",
 "footprint": "/home/adom/project/basic-parts-overhaul/pages-extra/amplh5030s-150mt/AMPLH5030S-150MT.kicad_mod",
 "standUp": [
  {
   "axis": "x",
   "quarterTurns": 1
  }
 ],
 "standUpSource": "footprint model rotate",
 "face": "top",
 "pin1": {
  "source": "footprint pad 1",
  "xyMm": [
   -2.175,
   -0.0
  ],
  "corner": "left/middle"
 },
 "existingMarks": [],
 "vendorMarking": {
  "present": true,
  "glyphFaces": 136
 },
 "faceNormal": [
  0,
  0,
  1
 ],
 "longAxis": {
  "axis": "x",
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "why": "two-terminal part: along the body, pad 1 to pad 2 (between the terminations)",
  "override": null
 },
 "readingDirection": {
  "vector": [
   1.0,
   0.0,
   0.0
  ],
  "angleDeg": 0,
  "textUp": [
   -0.0,
   1.0,
   0.0
  ],
  "rule": "pin 1 / pad 1 at the start (left) of the text, and below it when it sits on a side"
 },
 "band": {
  "regionMm": [
   -2.7,
   -2.6,
   2.7,
   2.6
  ],
  "zMm": 2.75,
  "lengthMm": 5.4,
  "heightMm": 5.2,
  "why": "highest flat face over the body centre",
  "terminationsExcludedBy": null,
  "trimmedEnds": [],
  "keepouts": [],
  "sideTurn": null,
  "margins": {
   "lengthEachSide": 0.12,
   "heightEachSide": 0.15
  }
 },
 "text": {
  "lines": [
   "AMPLH5030",
   "S-150MT"
  ],
  "chars": 16,
  "capHeightMm": 0.57,
  "smallestLineMm": 0.57,
  "heightPctOfBand": 25.2,
  "why": "two lines: the smaller line (0.570 mm) beats one line (0.317 mm) by 1.80x",
  "alternative": {
   "lines": [
    "AMPLH5030S-150MT"
   ],
   "capHeightMm": 0.3172,
   "smallestLineMm": 0.3172
  },
  "font": "service-step2glb /laser-etch (single-stroke outline font)"
 },
 "etch": {
  "poseQuarterTurnsZ": 0,
  "service": "/laser-etch?mode=flat",
  "note": "turn so the reading direction is +X, etch, fit the mark into the band, turn back"
 },
 "outline": {
  "upAxis": "z",
  "poseRotZDeg": 180,
  "rot": 180,
  "recipe": "adom-aiflow-etch outline <part.step> --footprint <part.kicad_mod> --mpn AMPLH5030S-150MT (stands the STEP up (footprint model rotate), turns it 180 deg about Z and draws AMPLH5030 / S-150MT on the planned band, rot 180)",
  "why": "iso camera looks from +X+Y+Z: text along +Y (rot 90) or -X (rot 180) reads left to right with pin 1 toward the viewer"
 },
 "widget": {
  "px": 320,
  "pxPerMm": 38.42,
  "capHeightPx": 17.9
 },
 "hints": [],
 "warnings": [
  "the vendor model already carries a printed marking (136 glyph faces on the top): keep the vendor model and do not etch over it (adom-aiflow-etch refuses unless --over-vendor-mark)"
 ],
 "summary": "Mark along the 5.40 mm axis (+X), 0.57 mm text (2 lines), upright with pin 1 left middle, outline rot 180 after a 180 deg pose turn; ~18 px caps at 320 px"
}