← Commit history

Initial commit: component/zlg7289bs

Ray ·73d957ee69 ·
2 files changed +329
README.mdadded+65
@@ -0,0 +1,65 @@+# ZLG7289BS++**ZLG Zhiyuan Elec** · Digital Tube Drivers · SOP-28-300mil++ZLG7289BS from ZLG Zhiyuan Elec, in a SOP-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD | power_in | Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected. |+| 2 | VDD | power_in | Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected. |+| 3 | NC | unconnected | No internal connection (悬空); leave floating. |+| 4 | VSS | power_in | Ground reference, 0 V; negative supply return for all internal circuitry. |+| 5 | NC | unconnected | No internal connection (悬空); leave floating. |+| 6 | /CS | input | Active-low SPI chip-select input; device accepts commands and returns keyboard data only while this pin is held low. |+| 7 | CLK | input | SPI synchronous clock input; synchronises serial data transfer on the DATA pin; clock rate is set by the host controller. |+| 8 | DATA | bidirectional | Bidirectional SPI serial data pin; acts as input when receiving commands or display data, switches to output on the falling edge of the last CLK cycle during a keyboard-read command. |+| 9 | KEY | output | Active-low open-drain keyboard interrupt output; remains high when no key is pressed, pulls low when a key closure is detected; maximum sink current 7 mA (IKO). |+| 10 | SG | output | Segment G LED drive output; directly drives the g segment of the multiplexed 7-segment LED display. |+| 11 | SF | output | Segment F LED drive output; directly drives the f segment of the multiplexed 7-segment LED display. |+| 12 | SE | output | Segment E LED drive output; directly drives the e segment of the multiplexed 7-segment LED display. |+| 13 | SD | output | Segment D LED drive output; directly drives the d segment of the multiplexed 7-segment LED display. |+| 14 | SC | output | Segment C LED drive output; directly drives the c segment of the multiplexed 7-segment LED display. |+| 15 | SB | output | Segment B LED drive output; directly drives the b segment of the multiplexed 7-segment LED display. |+| 16 | SA | output | Segment A LED drive output; directly drives the a segment of the multiplexed 7-segment LED display. |+| 17 | DP | output | Decimal point LED segment drive output; drives the DP segment of the multiplexed 7-segment LED display. |+| 18 | DIG0 | output | Digit 0 common drive output; selects digit position 0 during multiplexed LED display scan. |+| 19 | DIG1 | output | Digit 1 common drive output; selects digit position 1 during multiplexed LED display scan. |+| 20 | DIG2 | output | Digit 2 common drive output; selects digit position 2 during multiplexed LED display scan. |+| 21 | DIG3 | output | Digit 3 common drive output; selects digit position 3 during multiplexed LED display scan. |+| 22 | DIG4 | output | Digit 4 common drive output; selects digit position 4 during multiplexed LED display scan. |+| 23 | DIG5 | output | Digit 5 common drive output; selects digit position 5 during multiplexed LED display scan. |+| 24 | DIG6 | output | Digit 6 common drive output; selects digit position 6 during multiplexed LED display scan. |+| 25 | DIG7 | output | Digit 7 common drive output; selects digit position 7 during multiplexed LED display scan. |+| 26 | OSC2 | output | Crystal oscillator output terminal; connect to crystal resonator (12 MHz recommended); leave open when driving OSC1 with an external clock. |+| 27 | OSC1 | input | Crystal oscillator input terminal; connect to 12 MHz crystal resonator or external clock source; application example uses 12 MHz crystal. |+| 28 | /RESET | input | Active-low asynchronous reset input; hold low to reset the device; requires approximately 16 ms settling time after the rising edge before normal operation resumes. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | ZLG Zhiyuan Elec |+| Package | SOP-28-300mil |+| Category | LED Drivers |+| Pins | 28 |++## CAD (KiCad official)++- Symbol: `ZLG7289BS`+- Footprint: `Package_SO:SOP-28_8.4x18.16mm_P1.27mm`+- 3D model: SOP-28-300mil (KiCad packages3D, STEP)+- 3D model files: `zlg7289bs-etched.step` / `zlg7289bs-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `zlg7289bs.step` / `zlg7289bs.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [ZLG Zhiyuan Elec datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588882451350867968) (13 pp, sha256 `fba28104c7c03c0d`, retrieved 2026-09-22, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-sonnet-4-6` (vision), consensus `claude-opus-4-7` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/zlg7289bs-datasheet.pdf)
page.jsonadded+264
@@ -0,0 +1,264 @@+{+  "slug": "zlg7289bs",+  "version": "0.1.0",+  "type": "component",+  "description": "ZLG Zhiyuan Elec Digital Tube Drivers, SOP-28-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "led drivers",+    "zlg7289bs",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "zlg7289bs.kicad_sym",+    "zlg7289bs.kicad_mod",+    "zlg7289bs.glb",+    "zlg7289bs.step",+    "zlg7289bs.lbr",+    "docs/hero.png",+    "docs/zlg7289bs-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "ZLG7289BS",+    "manufacturer": "ZLG Zhiyuan Elec",+    "package": "SOP-28-300mil",+    "pin_count": 28,+    "category": "LED Drivers",+    "subcategory": "Digital Tube Drivers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588882451350867968",+    "parts": {+      "symbol": "zlg7289bs.kicad_sym",+      "footprint": "zlg7289bs.kicad_mod",+      "model_3d": "zlg7289bs-etched.glb",+      "model_3d_plain": "zlg7289bs.glb",+      "model_3d_step": "zlg7289bs-etched.step",+      "model_3d_step_plain": "zlg7289bs.step",+      "lbr": "zlg7289bs.lbr"+    },+    "distributor_links": {+      "lcsc": "C42732"+    },+    "pins": [+      {+        "number": "1",+        "name": "VDD",+        "type": "power_in",+        "description": "Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected."+      },+      {+        "number": "2",+        "name": "VDD",+        "type": "power_in",+        "description": "Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected."+      },+      {+        "number": "3",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection (悬空); leave floating."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference, 0 V; negative supply return for all internal circuitry."+      },+      {+        "number": "5",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection (悬空); leave floating."+      },+      {+        "number": "6",+        "name": "/CS",+        "type": "input",+        "description": "Active-low SPI chip-select input; device accepts commands and returns keyboard data only while this pin is held low."+      },+      {+        "number": "7",+        "name": "CLK",+        "type": "input",+        "description": "SPI synchronous clock input; synchronises serial data transfer on the DATA pin; clock rate is set by the host controller."+      },+      {+        "number": "8",+        "name": "DATA",+        "type": "bidirectional",+        "description": "Bidirectional SPI serial data pin; acts as input when receiving commands or display data, switches to output on the falling edge of the last CLK cycle during a keyboard-read command."+      },+      {+        "number": "9",+        "name": "KEY",+        "type": "output",+        "description": "Active-low open-drain keyboard interrupt output; remains high when no key is pressed, pulls low when a key closure is detected; maximum sink current 7 mA (IKO)."+      },+      {+        "number": "10",+        "name": "SG",+        "type": "output",+        "description": "Segment G LED drive output; directly drives the g segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "11",+        "name": "SF",+        "type": "output",+        "description": "Segment F LED drive output; directly drives the f segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "12",+        "name": "SE",+        "type": "output",+        "description": "Segment E LED drive output; directly drives the e segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "13",+        "name": "SD",+        "type": "output",+        "description": "Segment D LED drive output; directly drives the d segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "14",+        "name": "SC",+        "type": "output",+        "description": "Segment C LED drive output; directly drives the c segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "15",+        "name": "SB",+        "type": "output",+        "description": "Segment B LED drive output; directly drives the b segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "16",+        "name": "SA",+        "type": "output",+        "description": "Segment A LED drive output; directly drives the a segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "17",+        "name": "DP",+        "type": "output",+        "description": "Decimal point LED segment drive output; drives the DP segment of the multiplexed 7-segment LED display."+      },+      {+        "number": "18",+        "name": "DIG0",+        "type": "output",+        "description": "Digit 0 common drive output; selects digit position 0 during multiplexed LED display scan."+      },+      {+        "number": "19",+        "name": "DIG1",+        "type": "output",+        "description": "Digit 1 common drive output; selects digit position 1 during multiplexed LED display scan."+      },+      {+        "number": "20",+        "name": "DIG2",+        "type": "output",+        "description": "Digit 2 common drive output; selects digit position 2 during multiplexed LED display scan."+      },+      {+        "number": "21",+        "name": "DIG3",+        "type": "output",+        "description": "Digit 3 common drive output; selects digit position 3 during multiplexed LED display scan."+      },+      {+        "number": "22",+        "name": "DIG4",+        "type": "output",+        "description": "Digit 4 common drive output; selects digit position 4 during multiplexed LED display scan."+      },+      {+        "number": "23",+        "name": "DIG5",+        "type": "output",+        "description": "Digit 5 common drive output; selects digit position 5 during multiplexed LED display scan."+      },+      {+        "number": "24",+        "name": "DIG6",+        "type": "output",+        "description": "Digit 6 common drive output; selects digit position 6 during multiplexed LED display scan."+      },+      {+        "number": "25",+        "name": "DIG7",+        "type": "output",+        "description": "Digit 7 common drive output; selects digit position 7 during multiplexed LED display scan."+      },+      {+        "number": "26",+        "name": "OSC2",+        "type": "output",+        "description": "Crystal oscillator output terminal; connect to crystal resonator (12 MHz recommended); leave open when driving OSC1 with an external clock."+      },+      {+        "number": "27",+        "name": "OSC1",+        "type": "input",+        "description": "Crystal oscillator input terminal; connect to 12 MHz crystal resonator or external clock source; application example uses 12 MHz crystal."+      },+      {+        "number": "28",+        "name": "/RESET",+        "type": "input",+        "description": "Active-low asynchronous reset input; hold low to reset the device; requires approximately 16 ms settling time after the rising edge before normal operation resumes."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-sonnet-4-6",+        "primary_mode": "vision",+        "consensus_model": "claude-opus-4-7",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin 9 (KEY) does not appear as an explicit numbered row in the pin-description table on page 2. It i; The package mechanical drawing on page 12 is for a 28-Lead PDIP (600 mil), not the SOP-28-300 mil va",+          "vision extraction: provenance cannot be text-verified; needs consensus"+        ],+        "pages_sent": 12,+        "cost_usd": 0.3869,+        "at": "2026-09-22T08:31:31"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588882451350867968",+        "pages": 13,+        "sha256": "fba28104c7c03c0d",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 28,+        "described": 28,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file