Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ZLG7289BS

ZLG Zhiyuan Elec · Digital Tube Drivers · SOP-28-300mil

ZLG7289BS from ZLG Zhiyuan Elec, in a SOP-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected.
2 VDD power_in Positive supply voltage; operating range 2.7-5.5 V; both VDD pins (1 and 2) must be connected.
3 NC unconnected No internal connection (悬空); leave floating.
4 VSS power_in Ground reference, 0 V; negative supply return for all internal circuitry.
5 NC unconnected No internal connection (悬空); leave floating.
6 /CS input Active-low SPI chip-select input; device accepts commands and returns keyboard data only while this pin is held low.
7 CLK input SPI synchronous clock input; synchronises serial data transfer on the DATA pin; clock rate is set by the host controller.
8 DATA bidirectional Bidirectional SPI serial data pin; acts as input when receiving commands or display data, switches to output on the falling edge of the last CLK cycle during a keyboard-read command.
9 KEY output Active-low open-drain keyboard interrupt output; remains high when no key is pressed, pulls low when a key closure is detected; maximum sink current 7 mA (IKO).
10 SG output Segment G LED drive output; directly drives the g segment of the multiplexed 7-segment LED display.
11 SF output Segment F LED drive output; directly drives the f segment of the multiplexed 7-segment LED display.
12 SE output Segment E LED drive output; directly drives the e segment of the multiplexed 7-segment LED display.
13 SD output Segment D LED drive output; directly drives the d segment of the multiplexed 7-segment LED display.
14 SC output Segment C LED drive output; directly drives the c segment of the multiplexed 7-segment LED display.
15 SB output Segment B LED drive output; directly drives the b segment of the multiplexed 7-segment LED display.
16 SA output Segment A LED drive output; directly drives the a segment of the multiplexed 7-segment LED display.
17 DP output Decimal point LED segment drive output; drives the DP segment of the multiplexed 7-segment LED display.
18 DIG0 output Digit 0 common drive output; selects digit position 0 during multiplexed LED display scan.
19 DIG1 output Digit 1 common drive output; selects digit position 1 during multiplexed LED display scan.
20 DIG2 output Digit 2 common drive output; selects digit position 2 during multiplexed LED display scan.
21 DIG3 output Digit 3 common drive output; selects digit position 3 during multiplexed LED display scan.
22 DIG4 output Digit 4 common drive output; selects digit position 4 during multiplexed LED display scan.
23 DIG5 output Digit 5 common drive output; selects digit position 5 during multiplexed LED display scan.
24 DIG6 output Digit 6 common drive output; selects digit position 6 during multiplexed LED display scan.
25 DIG7 output Digit 7 common drive output; selects digit position 7 during multiplexed LED display scan.
26 OSC2 output Crystal oscillator output terminal; connect to crystal resonator (12 MHz recommended); leave open when driving OSC1 with an external clock.
27 OSC1 input Crystal oscillator input terminal; connect to 12 MHz crystal resonator or external clock source; application example uses 12 MHz crystal.
28 /RESET input Active-low asynchronous reset input; hold low to reset the device; requires approximately 16 ms settling time after the rising edge before normal operation resumes.

Key specifications

Parameter Value
Manufacturer ZLG Zhiyuan Elec
Package SOP-28-300mil
Category LED Drivers
Pins 28

CAD (KiCad official)

  • Symbol: ZLG7289BS
  • Footprint: Package_SO:SOP-28_8.4x18.16mm_P1.27mm
  • 3D model: SOP-28-300mil (KiCad packages3D, STEP)
  • 3D model files: zlg7289bs-etched.step / zlg7289bs-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); zlg7289bs.step / zlg7289bs.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ZLG Zhiyuan Elec datasheet (13 pp, sha256 fba28104c7c03c0d, retrieved 2026-09-22, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-sonnet-4-6 (vision), consensus claude-opus-4-7 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF