← Commit history

Initial commit: component/yt8511h

Ray ·b5880a33c7 ·
2 files changed +418
README.mdadded+77
@@ -0,0 +1,77 @@+# YT8511H++**Motorcomm** · Ethernet Transceivers · QFN-40-EP(5x5)++YT8511H from Motorcomm, in a QFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RESET_N | input | System reset, active low, requires external pull-up resistor. |+| 2 | LX | passive | Power inductor pin, add external 4.7 µH power inductor between this pin and pin 38. |+| 3 | VDD33 | power_in | 3.3V power supply for switching regulator. |+| 4 | XTLO | output | Crystal oscillator output, add capacitor to GND. |+| 5 | XTLI | input | Crystal oscillator input, requires capacitor to GND, supports 25 MHz external clock input. |+| 6 | AVDDL | power_in | 1.2V analog power input, connect to pin 38 through bead. |+| 7 | RBIAS | output | External 2.4 kΩ 1% resistor to GND to set bias current. |+| 8 | VDDH_REG | power_out | 3.3V or 2.5V regulator output with 1 µF capacitor to GND. |+| 9 | TRXP0 | passive | Media-dependent interface 0 positive, 100Ω transmission line. |+| 10 | TRXN0 | passive | Media-dependent interface 0 negative, 100Ω transmission line. |+| 11 | AVDDL | power_in | 1.2V analog power input, connect to pin 38 through bead. |+| 12 | TRXP1 | passive | Media-dependent interface 1 positive, 100Ω transmission line. |+| 13 | TRXN1 | passive | Media-dependent interface 1 negative, 100Ω transmission line. |+| 14 | AVDD33 | power_in | Analog 3.3V power input for PHY, from VDD33 through bead. |+| 15 | TRXP2 | passive | Media-dependent interface 2 positive, 100Ω transmission line. |+| 16 | TRXN2 | passive | Media-dependent interface 2 negative, 100Ω transmission line. |+| 17 | AVDDL | power_in | 1.2V analog power input, connect to pin 38 through bead. |+| 18 | TRXP3 | passive | Media-dependent interface 3 positive, 100Ω transmission line. |+| 19 | TRXN3 | passive | Media-dependent interface 3 negative, 100Ω transmission line. |+| 20 | INT | tri_state | Interrupt signal to system, open-drain gate output, requires external pull-up resistor. |+| 21 | LED_ACT | bidirectional | Parallel LED output for 10/100/1000 BASE-T activity, active low if pulled up, active high if pulled down. |+| 22 | LED_1000 | bidirectional | Parallel LED output for 1000 BASE-T link status. |+| 23 | CLK_25M | output | 25 MHz clock output (default), configurable to 125, 62.5, or 25 MHz. |+| 24 | LED_10_100 | bidirectional | Parallel LED output for 10/100 BASE-T link status. |+| 25 | RXD[3] | bidirectional | RGMII received data 3, sampled on power-on for low power mode strapping. |+| 26 | RXD[2] | bidirectional | RGMII received data 2, sampled on power-on for PLL enable strapping. |+| 27 | VDDIO | power_in | VDDIO input, connect directly to pin 8 (VDDH_REG). |+| 28 | RXD[1] | bidirectional | RGMII received data 1, sampled on power-on for PHY address bit 1 strapping. |+| 29 | RXD[0] | bidirectional | RGMII received data 0, sampled on power-on for PHY address bit 0 strapping. |+| 30 | RX_DV | bidirectional | RGMII receive data valid, sampled on power-on for RGMII IO power selection strapping. |+| 31 | RX_CLK | bidirectional | 125 MHz digital RGMII receive clock, add 22 ohm damping resistor near PHY for EMI design. |+| 32 | TX_EN | input | RGMII transmit enable from MAC. |+| 33 | GTX_CLK | input | RGMII transmit clock, 125/25/2.5 MHz digital, add 22 ohm damping resistor near MAC for EMI design. |+| 34 | TXD[0] | input | RGMII transmit data 0 from MAC. |+| 35 | TXD[1] | input | RGMII transmit data 1 from MAC. |+| 36 | TXD[2] | input | RGMII transmit data 2 from MAC. |+| 37 | TXD[3] | input | RGMII transmit data 3 from MAC. |+| 38 | DVDDL | power_in | 1.2V digital core power input, connect to power inductor and 10 µF + 0.1 µF ceramic capacitors to GND. |+| 39 | MDIO | bidirectional | Management data interface with internal pull-up resistor to 3.3V/2.5V. |+| 40 | MDC | input | Management data clock reference with internal pull-up resistor. |+| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Motorcomm |+| Package | QFN-40-EP(5x5) |+| Category | Interface |+| Pins | 41 |++## CAD (KiCad official)++- Symbol: `YT8511H`+- Footprint: `Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm`+- 3D model: QFN-40-EP(5x5) (KiCad packages3D, STEP)+- 3D model files: `yt8511h-etched.step` / `yt8511h-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `yt8511h.step` / `yt8511h.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Motorcomm datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589040657105502208) (92 pp, sha256 `8fc5947825b02d7c`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/yt8511h-datasheet.pdf)
page.jsonadded+341
@@ -0,0 +1,341 @@+{+  "slug": "yt8511h",+  "version": "0.1.0",+  "type": "component",+  "description": "Motorcomm Ethernet Transceivers, QFN-40-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "yt8511h",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "yt8511h.kicad_sym",+    "yt8511h.kicad_mod",+    "yt8511h.glb",+    "yt8511h.step",+    "yt8511h.lbr",+    "docs/hero.png",+    "docs/yt8511h-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "YT8511H",+    "manufacturer": "Motorcomm",+    "package": "QFN-40-EP(5x5)",+    "pin_count": 41,+    "category": "Interface",+    "subcategory": "Ethernet Transceivers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589040657105502208",+    "parts": {+      "symbol": "yt8511h.kicad_sym",+      "footprint": "yt8511h.kicad_mod",+      "model_3d": "yt8511h-etched.glb",+      "model_3d_plain": "yt8511h.glb",+      "model_3d_step": "yt8511h-etched.step",+      "model_3d_step_plain": "yt8511h.step",+      "lbr": "yt8511h.lbr"+    },+    "distributor_links": {+      "lcsc": "C2685352"+    },+    "pins": [+      {+        "number": "1",+        "name": "RESET_N",+        "type": "input",+        "description": "System reset, active low, requires external pull-up resistor."+      },+      {+        "number": "2",+        "name": "LX",+        "type": "passive",+        "description": "Power inductor pin, add external 4.7 µH power inductor between this pin and pin 38."+      },+      {+        "number": "3",+        "name": "VDD33",+        "type": "power_in",+        "description": "3.3V power supply for switching regulator."+      },+      {+        "number": "4",+        "name": "XTLO",+        "type": "output",+        "description": "Crystal oscillator output, add capacitor to GND."+      },+      {+        "number": "5",+        "name": "XTLI",+        "type": "input",+        "description": "Crystal oscillator input, requires capacitor to GND, supports 25 MHz external clock input."+      },+      {+        "number": "6",+        "name": "AVDDL",+        "type": "power_in",+        "description": "1.2V analog power input, connect to pin 38 through bead."+      },+      {+        "number": "7",+        "name": "RBIAS",+        "type": "output",+        "description": "External 2.4 kΩ 1% resistor to GND to set bias current."+      },+      {+        "number": "8",+        "name": "VDDH_REG",+        "type": "power_out",+        "description": "3.3V or 2.5V regulator output with 1 µF capacitor to GND."+      },+      {+        "number": "9",+        "name": "TRXP0",+        "type": "passive",+        "description": "Media-dependent interface 0 positive, 100Ω transmission line."+      },+      {+        "number": "10",+        "name": "TRXN0",+        "type": "passive",+        "description": "Media-dependent interface 0 negative, 100Ω transmission line."+      },+      {+        "number": "11",+        "name": "AVDDL",+        "type": "power_in",+        "description": "1.2V analog power input, connect to pin 38 through bead."+      },+      {+        "number": "12",+        "name": "TRXP1",+        "type": "passive",+        "description": "Media-dependent interface 1 positive, 100Ω transmission line."+      },+      {+        "number": "13",+        "name": "TRXN1",+        "type": "passive",+        "description": "Media-dependent interface 1 negative, 100Ω transmission line."+      },+      {+        "number": "14",+        "name": "AVDD33",+        "type": "power_in",+        "description": "Analog 3.3V power input for PHY, from VDD33 through bead."+      },+      {+        "number": "15",+        "name": "TRXP2",+        "type": "passive",+        "description": "Media-dependent interface 2 positive, 100Ω transmission line."+      },+      {+        "number": "16",+        "name": "TRXN2",+        "type": "passive",+        "description": "Media-dependent interface 2 negative, 100Ω transmission line."+      },+      {+        "number": "17",+        "name": "AVDDL",+        "type": "power_in",+        "description": "1.2V analog power input, connect to pin 38 through bead."+      },+      {+        "number": "18",+        "name": "TRXP3",+        "type": "passive",+        "description": "Media-dependent interface 3 positive, 100Ω transmission line."+      },+      {+        "number": "19",+        "name": "TRXN3",+        "type": "passive",+        "description": "Media-dependent interface 3 negative, 100Ω transmission line."+      },+      {+        "number": "20",+        "name": "INT",+        "type": "tri_state",+        "description": "Interrupt signal to system, open-drain gate output, requires external pull-up resistor."+      },+      {+        "number": "21",+        "name": "LED_ACT",+        "type": "bidirectional",+        "description": "Parallel LED output for 10/100/1000 BASE-T activity, active low if pulled up, active high if pulled down."+      },+      {+        "number": "22",+        "name": "LED_1000",+        "type": "bidirectional",+        "description": "Parallel LED output for 1000 BASE-T link status."+      },+      {+        "number": "23",+        "name": "CLK_25M",+        "type": "output",+        "description": "25 MHz clock output (default), configurable to 125, 62.5, or 25 MHz."+      },+      {+        "number": "24",+        "name": "LED_10_100",+        "type": "bidirectional",+        "description": "Parallel LED output for 10/100 BASE-T link status."+      },+      {+        "number": "25",+        "name": "RXD[3]",+        "type": "bidirectional",+        "description": "RGMII received data 3, sampled on power-on for low power mode strapping."+      },+      {+        "number": "26",+        "name": "RXD[2]",+        "type": "bidirectional",+        "description": "RGMII received data 2, sampled on power-on for PLL enable strapping."+      },+      {+        "number": "27",+        "name": "VDDIO",+        "type": "power_in",+        "description": "VDDIO input, connect directly to pin 8 (VDDH_REG)."+      },+      {+        "number": "28",+        "name": "RXD[1]",+        "type": "bidirectional",+        "description": "RGMII received data 1, sampled on power-on for PHY address bit 1 strapping."+      },+      {+        "number": "29",+        "name": "RXD[0]",+        "type": "bidirectional",+        "description": "RGMII received data 0, sampled on power-on for PHY address bit 0 strapping."+      },+      {+        "number": "30",+        "name": "RX_DV",+        "type": "bidirectional",+        "description": "RGMII receive data valid, sampled on power-on for RGMII IO power selection strapping."+      },+      {+        "number": "31",+        "name": "RX_CLK",+        "type": "bidirectional",+        "description": "125 MHz digital RGMII receive clock, add 22 ohm damping resistor near PHY for EMI design."+      },+      {+        "number": "32",+        "name": "TX_EN",+        "type": "input",+        "description": "RGMII transmit enable from MAC."+      },+      {+        "number": "33",+        "name": "GTX_CLK",+        "type": "input",+        "description": "RGMII transmit clock, 125/25/2.5 MHz digital, add 22 ohm damping resistor near MAC for EMI design."+      },+      {+        "number": "34",+        "name": "TXD[0]",+        "type": "input",+        "description": "RGMII transmit data 0 from MAC."+      },+      {+        "number": "35",+        "name": "TXD[1]",+        "type": "input",+        "description": "RGMII transmit data 1 from MAC."+      },+      {+        "number": "36",+        "name": "TXD[2]",+        "type": "input",+        "description": "RGMII transmit data 2 from MAC."+      },+      {+        "number": "37",+        "name": "TXD[3]",+        "type": "input",+        "description": "RGMII transmit data 3 from MAC."+      },+      {+        "number": "38",+        "name": "DVDDL",+        "type": "power_in",+        "description": "1.2V digital core power input, connect to power inductor and 10 µF + 0.1 µF ceramic capacitors to GND."+      },+      {+        "number": "39",+        "name": "MDIO",+        "type": "bidirectional",+        "description": "Management data interface with internal pull-up resistor to 3.3V/2.5V."+      },+      {+        "number": "40",+        "name": "MDC",+        "type": "input",+        "description": "Management data clock reference with internal pull-up resistor."+      },+      {+        "number": "41",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 41 added from the footprint"+        ],+        "pages_sent": 92,+        "cost_usd": 0.7175,+        "at": "2026-09-22T00:07:07"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589040657105502208",+        "pages": 92,+        "sha256": "8fc5947825b02d7c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 41,+        "described": 41,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file