main
Ray
Publish 0.1.0
d4b97cc
YT8511C
Motorcomm · Ethernet Transceivers · QFN-40-EP(5x5)
YT8511C from Motorcomm, in a QFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RESET_N | input | System reset, active low; requires an external pull-up resistor. |
| 2 | LX | passive | Power inductor pin; add an external 4.7 uH power inductor between this pin and pin 38. |
| 3 | VDD33 | power_in | 3.3 V power input for the switching regulator. |
| 4 | XTLO | passive | Crystal oscillator output; add a capacitor to GND. |
| 5 | XTLI | input | Crystal oscillator input that requires a capacitor to GND; also accepts an external 25 MHz, 1.2 V swing clock. |
| 6 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 7 | RBIAS | passive | External 2.4 k ohm 1% resistor to GND sets the bias current. |
| 8 | VDDH_REG | power_out | 3.3 V or 2.5 V regulator output; a 1 uF capacitor to GND is connected to this pin. |
| 9 | TRXP0 | passive | Media-dependent interface 0 positive line, 100 ohm transmission line. |
| 10 | TRXN0 | passive | Media-dependent interface 0 negative line, 100 ohm transmission line. |
| 11 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 12 | TRXP1 | passive | Media-dependent interface 1 positive line, 100 ohm transmission line. |
| 13 | TRXN1 | passive | Media-dependent interface 1 negative line, 100 ohm transmission line. |
| 14 | AVDD33 | power_in | Analog 3.3 V power input for the PHY, fed from VDD33 through a bead. |
| 15 | TRXP2 | passive | Media-dependent interface 2 positive line, 100 ohm transmission line. |
| 16 | TRXN2 | passive | Media-dependent interface 2 negative line, 100 ohm transmission line. |
| 17 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 18 | TRXP3 | passive | Media-dependent interface 3 positive line, 100 ohm transmission line. |
| 19 | TRXN3 | passive | Media-dependent interface 3 negative line, 100 ohm transmission line. |
| 20 | INT | bidirectional | Interrupt signal to the system; default open-drain output that needs an external pull-up resistor. |
| 21 | LED_ACT | bidirectional | Parallel LED output for 10/100/1000 BASE-T activity with active blinking; active level is set by power-on strapping (pulled up = active low, pulled down = active high). |
| 22 | LED_1000 | bidirectional | Parallel LED output for 1000 BASE-T link; active level is set by power-on strapping. |
| 23 | CLK_25M | output | 25 MHz clock output by default; can be configured as 125, 62.5 or 25 MHz clock output. |
| 24 | LED_10_100 | bidirectional | Parallel LED output for 10/100 BASE-T link. |
| 25 | RXD[3] | bidirectional | RGMII received data bit 3, with internal pull-down. |
| 26 | RXD[2] | bidirectional | RGMII received data bit 2, with internal pull-down. |
| 27 | VDDIO | power_in | VDDIO input for the RGMII I/O; connect directly to pin 8 (VDDH_REG). |
| 28 | RXD[1] | bidirectional | RGMII received data bit 1, with internal pull-down. |
| 29 | RXD[0] | bidirectional | RGMII received data bit 0, with internal pull-down. |
| 30 | RX_DV | bidirectional | RGMII receive data valid, with internal pull-down. |
| 31 | RX_CLK | bidirectional | 125 MHz RGMII receive clock with internal pull-down; a 22 ohm damping resistor is recommended near the PHY side. |
| 32 | TX_EN | input | RGMII transmit enable, with internal pull-down. |
| 33 | GTX_CLK | input | RGMII transmit clock at 125/25/2.5 MHz, with internal pull-down; a 22 ohm damping resistor is recommended near the MAC side. |
| 34 | TXD[0] | input | RGMII transmit data bit 0, with internal pull-down. |
| 35 | TXD[1] | input | RGMII transmit data bit 1, with internal pull-down. |
| 36 | TXD[2] | input | RGMII transmit data bit 2, with internal pull-down. |
| 37 | TXD[3] | input | RGMII transmit data bit 3, with internal pull-down. |
| 38 | DVDDL | power_in | 1.2 V digital core power input; connect to the power inductor and 10 uF + 0.1 uF ceramic capacitors to GND. |
| 39 | MDIO | bidirectional | Management data I/O with internal pull-up; requires a pull-up resistor to 3.3 V or 2.5 V. |
| 40 | MDC | input | Management data clock reference, with internal pull-up. |
| 41 | EPAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Motorcomm |
| Package | QFN-40-EP(5x5) |
| Category | Interface |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 3.3V Supply Voltage | VDD33, AVDD33 | 2.97 | 3.3 | 3.63 | V | 87 | |
| 2.5V RGMII Supply Voltage | 2.25 | 2.5 | 2.75 | V | 87 | ||
| Minimum High Level Output Voltage (3.3V) | Voh (3.3V) | 2.4 | V | 87 | |||
| Minimum High Level Output Voltage (2.5V) | Voh (2.5V) | 2 | V | 87 | |||
| Maximum Low Level Output Voltage (3.3V) | Vol (3.3V) | -0.3 | 0.4 | V | 87 | ||
| Maximum Low Level Output Voltage (2.5V) | Vol (2.5V) | -0.3 | 0.4 | V | 87 | ||
| Minimum High Level Input Voltage (3.3V) | Vih (3.3V) | 2 | V | 87 | |||
| Maximum Low Level Input Voltage (3.3V) | Vil (3.3V) | 0.8 | V | 87 | |||
| Minimum High Level Input Voltage (2.5V) | Vih (2.5V) | 1.7 | V | 87 | |||
| Maximum Low Level Input Voltage (2.5V) | Vil (2.5V) | 0.7 | V | 87 | |||
| Input Current | Iin | 0 | 0.5 | µA | Vin=VDD33 or GND | 87 | |
| Data to clock output skew (at Transmitter) | TskewT | -500 | 0 | 500 | ps | 84 | |
| Data to clock output skew (at Receiver) | TskewR | 1 | ns | 84 | |||
| Clock cycle duration | Tcyc | 7.2 | 8 | 8.8 | ns | 84 | |
| Duty cycle for Gigabit | Duty_G | 45 | 50 | 55 | % | 84 | |
| Duty cycle for 10/100T | Duty_T | 40 | 50 | 60 | % | 84 | |
| Rise/Fall time (20-80%) | Tr/Tf | 0.75 | ns | 20 - 80% | 84 | ||
| Data to Clock output Setup Time at Transmitter | TsetupT | 1.65 | 2 | 2.2 | ns | with delay integrated at transmitter | 85 |
| Clock to Data output Hold Time at Transmitter | TholdT | 1.65 | 2 | 2.2 | ns | with delay integrated at transmitter | 85 |
| Data to Clock input Setup Time at Receiver | TsetupR | 1 | 2 | ns | with delay integrated at transmitter | 85 | |
| Data to Clock output Setup Time at Receiver | TholdR | 1 | 2 | ns | with delay integrated at transmitter | 85 | |
| Input high current | IIH | 0.4 | mA | 85 | |||
| Input low current | IIL | 0.4 | mA | 85 | |||
| Output high voltage | VOH | 2.4 | V | 85 | |||
| Output low voltage | VOL | 0.4 | V | 85 | |||
| Input high voltage | VIH | 2 | V | 85 | |||
| Input low voltage | VIL | 0.8 | V | 85 | |||
| Crystal Reference Frequency tolerance | F ref Tolerance | -50 | 50 | ppm | 86 | ||
| Reference clock input duty cycle | Duty Cycle | 40 | 60 | % | 86 | ||
| Equivalent Series Resistance | ESR | 50 | ohm | 86 | |||
| Drive Level | DL | 0.5 | mW | 86 | |||
| Oscillator Frequency tolerance | -50 | 50 | PPM | Ta= -40~85 C | 86 | ||
| Oscillator Duty Cycle | 40 | 60 | % | 86 | |||
| Temperature Range (row printed as YT8512C) | 0 | 70 | °C | Temperature Range YT8512C | 86 |
CAD (KiCad official)
- Symbol:
YT8511C - Footprint:
Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm - 3D model: QFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
yt8511c-etched.step/yt8511c-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);yt8511c.step/yt8511c.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Motorcomm datasheet (92 pp, sha256
347dfaffbe68d4fd, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# YT8511C
**Motorcomm** · Ethernet Transceivers · QFN-40-EP(5x5)
YT8511C from Motorcomm, in a QFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RESET_N | input | System reset, active low; requires an external pull-up resistor. |
| 2 | LX | passive | Power inductor pin; add an external 4.7 uH power inductor between this pin and pin 38. |
| 3 | VDD33 | power_in | 3.3 V power input for the switching regulator. |
| 4 | XTLO | passive | Crystal oscillator output; add a capacitor to GND. |
| 5 | XTLI | input | Crystal oscillator input that requires a capacitor to GND; also accepts an external 25 MHz, 1.2 V swing clock. |
| 6 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 7 | RBIAS | passive | External 2.4 k ohm 1% resistor to GND sets the bias current. |
| 8 | VDDH_REG | power_out | 3.3 V or 2.5 V regulator output; a 1 uF capacitor to GND is connected to this pin. |
| 9 | TRXP0 | passive | Media-dependent interface 0 positive line, 100 ohm transmission line. |
| 10 | TRXN0 | passive | Media-dependent interface 0 negative line, 100 ohm transmission line. |
| 11 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 12 | TRXP1 | passive | Media-dependent interface 1 positive line, 100 ohm transmission line. |
| 13 | TRXN1 | passive | Media-dependent interface 1 negative line, 100 ohm transmission line. |
| 14 | AVDD33 | power_in | Analog 3.3 V power input for the PHY, fed from VDD33 through a bead. |
| 15 | TRXP2 | passive | Media-dependent interface 2 positive line, 100 ohm transmission line. |
| 16 | TRXN2 | passive | Media-dependent interface 2 negative line, 100 ohm transmission line. |
| 17 | AVDDL | power_in | 1.2 V analog power input; connect to pin 38 through a bead. |
| 18 | TRXP3 | passive | Media-dependent interface 3 positive line, 100 ohm transmission line. |
| 19 | TRXN3 | passive | Media-dependent interface 3 negative line, 100 ohm transmission line. |
| 20 | INT | bidirectional | Interrupt signal to the system; default open-drain output that needs an external pull-up resistor. |
| 21 | LED_ACT | bidirectional | Parallel LED output for 10/100/1000 BASE-T activity with active blinking; active level is set by power-on strapping (pulled up = active low, pulled down = active high). |
| 22 | LED_1000 | bidirectional | Parallel LED output for 1000 BASE-T link; active level is set by power-on strapping. |
| 23 | CLK_25M | output | 25 MHz clock output by default; can be configured as 125, 62.5 or 25 MHz clock output. |
| 24 | LED_10_100 | bidirectional | Parallel LED output for 10/100 BASE-T link. |
| 25 | RXD[3] | bidirectional | RGMII received data bit 3, with internal pull-down. |
| 26 | RXD[2] | bidirectional | RGMII received data bit 2, with internal pull-down. |
| 27 | VDDIO | power_in | VDDIO input for the RGMII I/O; connect directly to pin 8 (VDDH_REG). |
| 28 | RXD[1] | bidirectional | RGMII received data bit 1, with internal pull-down. |
| 29 | RXD[0] | bidirectional | RGMII received data bit 0, with internal pull-down. |
| 30 | RX_DV | bidirectional | RGMII receive data valid, with internal pull-down. |
| 31 | RX_CLK | bidirectional | 125 MHz RGMII receive clock with internal pull-down; a 22 ohm damping resistor is recommended near the PHY side. |
| 32 | TX_EN | input | RGMII transmit enable, with internal pull-down. |
| 33 | GTX_CLK | input | RGMII transmit clock at 125/25/2.5 MHz, with internal pull-down; a 22 ohm damping resistor is recommended near the MAC side. |
| 34 | TXD[0] | input | RGMII transmit data bit 0, with internal pull-down. |
| 35 | TXD[1] | input | RGMII transmit data bit 1, with internal pull-down. |
| 36 | TXD[2] | input | RGMII transmit data bit 2, with internal pull-down. |
| 37 | TXD[3] | input | RGMII transmit data bit 3, with internal pull-down. |
| 38 | DVDDL | power_in | 1.2 V digital core power input; connect to the power inductor and 10 uF + 0.1 uF ceramic capacitors to GND. |
| 39 | MDIO | bidirectional | Management data I/O with internal pull-up; requires a pull-up resistor to 3.3 V or 2.5 V. |
| 40 | MDC | input | Management data clock reference, with internal pull-up. |
| 41 | EPAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Motorcomm |
| Package | QFN-40-EP(5x5) |
| Category | Interface |
| Pins | 41 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 3.3V Supply Voltage | VDD33, AVDD33 | 2.97 | 3.3 | 3.63 | V | | 87 |
| 2.5V RGMII Supply Voltage | | 2.25 | 2.5 | 2.75 | V | | 87 |
| Minimum High Level Output Voltage (3.3V) | Voh (3.3V) | 2.4 | | | V | | 87 |
| Minimum High Level Output Voltage (2.5V) | Voh (2.5V) | 2 | | | V | | 87 |
| Maximum Low Level Output Voltage (3.3V) | Vol (3.3V) | -0.3 | | 0.4 | V | | 87 |
| Maximum Low Level Output Voltage (2.5V) | Vol (2.5V) | -0.3 | | 0.4 | V | | 87 |
| Minimum High Level Input Voltage (3.3V) | Vih (3.3V) | 2 | | | V | | 87 |
| Maximum Low Level Input Voltage (3.3V) | Vil (3.3V) | | | 0.8 | V | | 87 |
| Minimum High Level Input Voltage (2.5V) | Vih (2.5V) | 1.7 | | | V | | 87 |
| Maximum Low Level Input Voltage (2.5V) | Vil (2.5V) | | | 0.7 | V | | 87 |
| Input Current | Iin | 0 | | 0.5 | µA | Vin=VDD33 or GND | 87 |
| Data to clock output skew (at Transmitter) | TskewT | -500 | 0 | 500 | ps | | 84 |
| Data to clock output skew (at Receiver) | TskewR | 1 | | | ns | | 84 |
| Clock cycle duration | Tcyc | 7.2 | 8 | 8.8 | ns | | 84 |
| Duty cycle for Gigabit | Duty_G | 45 | 50 | 55 | % | | 84 |
| Duty cycle for 10/100T | Duty_T | 40 | 50 | 60 | % | | 84 |
| Rise/Fall time (20-80%) | Tr/Tf | | | 0.75 | ns | 20 - 80% | 84 |
| Data to Clock output Setup Time at Transmitter | TsetupT | 1.65 | 2 | 2.2 | ns | with delay integrated at transmitter | 85 |
| Clock to Data output Hold Time at Transmitter | TholdT | 1.65 | 2 | 2.2 | ns | with delay integrated at transmitter | 85 |
| Data to Clock input Setup Time at Receiver | TsetupR | 1 | | 2 | ns | with delay integrated at transmitter | 85 |
| Data to Clock output Setup Time at Receiver | TholdR | 1 | | 2 | ns | with delay integrated at transmitter | 85 |
| Input high current | IIH | | | 0.4 | mA | | 85 |
| Input low current | IIL | 0.4 | | | mA | | 85 |
| Output high voltage | VOH | 2.4 | | | V | | 85 |
| Output low voltage | VOL | | | 0.4 | V | | 85 |
| Input high voltage | VIH | 2 | | | V | | 85 |
| Input low voltage | VIL | | | 0.8 | V | | 85 |
| Crystal Reference Frequency tolerance | F ref Tolerance | -50 | | 50 | ppm | | 86 |
| Reference clock input duty cycle | Duty Cycle | 40 | | 60 | % | | 86 |
| Equivalent Series Resistance | ESR | | | 50 | ohm | | 86 |
| Drive Level | DL | | | 0.5 | mW | | 86 |
| Oscillator Frequency tolerance | | -50 | | 50 | PPM | Ta= -40~85 C | 86 |
| Oscillator Duty Cycle | | 40 | | 60 | % | | 86 |
| Temperature Range (row printed as YT8512C) | | 0 | | 70 | °C | Temperature Range YT8512C | 86 |
## CAD (KiCad official)
- Symbol: `YT8511C`
- Footprint: `Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm`
- 3D model: QFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `yt8511c-etched.step` / `yt8511c-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `yt8511c.step` / `yt8511c.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Motorcomm datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588919479954231296) (92 pp, sha256 `347dfaffbe68d4fd`, retrieved 2026-10-19, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/yt8511c-datasheet.pdf)