3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXW02E SOP8
Sam&wing · Touch Sensors · SOP-8
XW02E SOP8 from Sam&wing, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power ground (电源地) for the device; the datasheet specifies no separate limit for this pin. |
| 2 | C1 | passive | Internal balance capacitor interface; the datasheet gives a range of 1nF to 10nF with 4.7nF recommended, using a 10% tolerance NPO capacitor placed close to the IC. |
| 3 | CSEL | passive | Sensitivity adjustment capacitor interface; range 0 to 100pF, where a smaller capacitance gives higher sensitivity and leaving it open (0 pF) gives the highest sensitivity. |
| 4 | PAD0 | passive | Touch key 0 sensing pad input; the sensing pad area is recommended between 3mm3mm and 30mm30mm, with the same size for each pad. |
| 5 | PAD1 | passive | Touch key 1 sensing pad input; the sensing pad area is recommended between 3mm3mm and 30mm30mm, with the same size as PAD0. |
| 6 | OUT1 | output | Channel 1 open-drain output that goes low while touch key PAD1 is pressed and is high-impedance when released; an external pull-up resistor is required. |
| 7 | OUT0 | output | Channel 0 open-drain output that goes low while touch key PAD0 is pressed and is high-impedance when released; an external pull-up resistor is required. |
| 8 | VDD | power_in | Positive supply with an operating range of 2.5 to 5.5 V and an absolute maximum of -0.3 to 6.0 V; supply ripple and noise should be kept low. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sam&wing |
| Package | SOP-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 2.5 | 5.5 | V | 4 | ||
| Sensitivity capacitor range (CSEL) | CSEL | 0 | 5 | 100 | pF | 4 | |
| Chip sensing capacitance range | C_in | 0.2 | 100 | pF | 4 | ||
| Absolute maximum VDD voltage | VDD | -0.3 | 6 | V | 4 | ||
| Absolute maximum input/output voltage | -0.3 | 6 | V | 4 | |||
| Operating temperature range | -40 | 85 | °C | 4 | |||
| Storage temperature range | -55 | 150 | °C | 4 | |||
| ESD and HBM withstand | ESD, HUM | 8000 | V | 4 | |||
| Sleep mode operating current | I_sleep | 7 | uA | VDD=3.0V | 4 | ||
| Sleep mode operating current | I_sleep | 11 | uA | VDD=5.0V | 4 | ||
| Operating current | I_vdd | 394 | uA | VDD=3.0V | 4 | ||
| Operating current | I_vdd | 666 | uA | VDD=5.0V | 4 | ||
| Power-on initialization time | T_init | 300 | mS | 4 | |||
| Output sink current | IO_sink | 10 | mA | VDD=5.0V | 4 | ||
| C1 internal balance capacitor range | C1 | 1 | 4.7 | 10 | nF | 3 |
CAD (KiCad official)
- Symbol:
XW02E SOP8 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
xw02e-sop8-etched.step/xw02e-sop8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xw02e-sop8.step/xw02e-sop8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sam&wing datasheet (7 pp, sha256
0122f6d62fcae047, retrieved 2026-10-27, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).