main
Ray
Publish 0.1.0
d3e750a
XW01
Sam&wing · Touch Sensors · SOT-23-6
XW01 from Sam&wing, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Positive power supply input, 2.5V to 5.5V operating range, with a mandatory 20Ω series resistor from the supply and 100nF decoupling to GND. |
| 2 | GND | power_in | Negative power supply and reference ground. |
| 3 | OUT | output | Open-drain key-sense output that is high-impedance when no touch is detected and low when a touch is detected, requiring an external pull-up resistor to VDD. |
| 4 | C2 | input | Reference capacitor pin used as the detection comparison baseline, typically 5-15pF and larger than the total parasitic capacitance of the KEY pin (use a C0G/NP0 capacitor). |
| 5 | KEY | input | Touch sensing input connected through a series resistor of 2kΩ to 10kΩ (2kΩ typical) to the sense pad. |
| 6 | C1 | input | Internal balance capacitor interface, typically 4.7nF to GND (range 1nF to 10nF). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sam&wing |
| Package | SOT-23-6 |
| Category | Sensors |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 2.5 | 5.5 | V | TA = 25℃ | 6 | |
| Operating temperature | -40 | 85 | °C | 5 | |||
| Storage temperature | -50 | 150 | °C | 5 | |||
| Supply voltage | -0.3 | 5.5 | V | 5 | |||
| Pin maximum current | -20 | 20 | mA | 5 | |||
| Pin voltage | -0.3 | V | max VDD+0.3 V | 6 | |||
| Minimum detection capacitance | delta_CX | 0.2 | pF | TA = 25℃ | 6 | ||
| Output sink current | Isk | 10 | mA | VDD=5V | 6 | ||
| Supply current | Idd | 666 | uA | VDD=5.0V | 6 | ||
| Supply current | Idd | 394 | uA | VDD=3.0V | 6 | ||
| Supply current sleep | Idd | 55 | uA | VDD=5.0V & SLEEP | 6 | ||
| Supply current sleep | Idd | 30 | uA | VDD=3.0V & SLEEP | 6 | ||
| Power-up stabilization time | Tini | 300 | ms | 6 | |||
| Output impedance low level | Zo | 50 | Ohm | 低电平 (low level) | 6 | ||
| Sampling period | Tsi | 4 | ms | 正常工作状态 (normal operation) | 6 | ||
| ESD HBM | 8000 | V | H.B.M POS/NEG, VDD, GND, P to P | 6 | |||
| ESD MM | 500 | V | M.M POS/NEG, VDD, GND, P to P | 6 |
CAD (KiCad official)
- Symbol:
XW01 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
xw01-etched.step/xw01-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xw01.step/xw01.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sam&wing datasheet (7 pp, sha256
9f993e853c2e3903, retrieved 2026-10-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XW01
**Sam&wing** · Touch Sensors · SOT-23-6
XW01 from Sam&wing, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Positive power supply input, 2.5V to 5.5V operating range, with a mandatory 20Ω series resistor from the supply and 100nF decoupling to GND. |
| 2 | GND | power_in | Negative power supply and reference ground. |
| 3 | OUT | output | Open-drain key-sense output that is high-impedance when no touch is detected and low when a touch is detected, requiring an external pull-up resistor to VDD. |
| 4 | C2 | input | Reference capacitor pin used as the detection comparison baseline, typically 5-15pF and larger than the total parasitic capacitance of the KEY pin (use a C0G/NP0 capacitor). |
| 5 | KEY | input | Touch sensing input connected through a series resistor of 2kΩ to 10kΩ (2kΩ typical) to the sense pad. |
| 6 | C1 | input | Internal balance capacitor interface, typically 4.7nF to GND (range 1nF to 10nF). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sam&wing |
| Package | SOT-23-6 |
| Category | Sensors |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 2.5 | | 5.5 | V | TA = 25℃ | 6 |
| Operating temperature | | -40 | | 85 | °C | | 5 |
| Storage temperature | | -50 | | 150 | °C | | 5 |
| Supply voltage | | -0.3 | | 5.5 | V | | 5 |
| Pin maximum current | | -20 | | 20 | mA | | 5 |
| Pin voltage | | -0.3 | | | V | max VDD+0.3 V | 6 |
| Minimum detection capacitance | delta_CX | 0.2 | | | pF | TA = 25℃ | 6 |
| Output sink current | Isk | | 10 | | mA | VDD=5V | 6 |
| Supply current | Idd | | 666 | | uA | VDD=5.0V | 6 |
| Supply current | Idd | | 394 | | uA | VDD=3.0V | 6 |
| Supply current sleep | Idd | | 55 | | uA | VDD=5.0V & SLEEP | 6 |
| Supply current sleep | Idd | | 30 | | uA | VDD=3.0V & SLEEP | 6 |
| Power-up stabilization time | Tini | | 300 | | ms | | 6 |
| Output impedance low level | Zo | | 50 | | Ohm | 低电平 (low level) | 6 |
| Sampling period | Tsi | | 4 | | ms | 正常工作状态 (normal operation) | 6 |
| ESD HBM | | | | 8000 | V | H.B.M POS/NEG, VDD, GND, P to P | 6 |
| ESD MM | | | | 500 | V | M.M POS/NEG, VDD, GND, P to P | 6 |
## CAD (KiCad official)
- Symbol: `XW01`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `xw01-etched.step` / `xw01-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xw01.step` / `xw01.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Sam&wing datasheet](docs/xw01-datasheet.pdf) (7 pp, sha256 `9f993e853c2e3903`, retrieved 2026-10-23, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xw01-datasheet.pdf)