main
Ray
Publish 0.1.0
f76ae14
XTSDQ01GWSIGA
XTX · NAND FLASH · WSON-8-EP(6x8)
XTSDQ01GWSIGA from XTX, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DAT2 | bidirectional | SD mode Data Line [bit2], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode. |
| 2 | DAT3/CD | bidirectional | SD mode Data Line [bit3] / SD NAND detection (internal 10-90 kOhm pull-up that may be used for card detection), input on power up; Chip Select input in SPI mode. |
| 3 | CLK | input | Clock input in both SD and SPI modes, up to 50MHz in high speed mode and 25MHz in default mode. |
| 4 | VSS | power_in | Ground supply in both SD and SPI modes. |
| 5 | CMD | bidirectional | Command/Response push-pull line in SD mode (10-100 kOhm pull-up recommended to prevent bus floating); Data In input in SPI mode. |
| 6 | DAT0 | bidirectional | SD mode Data Line [bit0], push-pull I/O; Data Out push-pull output in SPI mode. |
| 7 | DAT1 | bidirectional | SD mode Data Line [bit1], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode. |
| 8 | VDD | power_in | Supply voltage of 1.7V to 1.95V for the XTSDQ series (absolute maximum 2.25V), with max 5uF capacitance on the supply line and 45uF decoupling recommended. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XTX |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 1.7 | 1.95 | V | TA=-40°C to 85°C | 19 | |
| Input Leakage Current | ILI | -2 | 2 | µA | 19 | ||
| Output Leakage Current | ILO | -2 | 2 | µA | 19 | ||
| Standby Current | ICC1 | 130 | 2500 | µA | VDD=1.95V | 19 | |
| Read Current | ICC2 | 32 | 75 | mA | FCLK=50MHz | 19 | |
| Write Current | ICC2 | 32 | 75 | mA | FCLK=50MHz | 19 | |
| Input Low Voltage | VIL | -0.3 | V | 19 | |||
| Output Low Voltage | VOL | 0.4 | V | IOL = 2mA | 19 | ||
| Operating Temperature | -40 | 85 | °C | 16 | |||
| Storage Temperature | -55 | 125 | °C | 16 | |||
| VDD (XTSDQ0x Series) | VDD | -0.3 | 2.25 | V | 16 | ||
| Voltage on I/O Pin with Respect to Ground (XTSDQ0x Series) | -0.3 | 2.25 | V | -0.3V to VDD+0.3 (<= 2.25V) | 16 | ||
| Total bus capacitance for each signal line | CL | 40 | pF | CHOST+CBUS <= 30pF | 16 | ||
| Single card capacitance | CCARD | 10 | pF | 16 | |||
| Pull-up resistance | RCMD | 10 | 100 | K Ohm | Prevent bus floating | 16 | |
| Maximum signal line inductance | 16 | nH | fPP <= 20MHz | 16 | |||
| Pull-up resistance inside card(pin1) | RDAT3 | 10 | 90 | K Ohm | May be used for card detection | 16 | |
| Capacity connected to power line | CC | 5 | uF | To prevent inrush current | 16 | ||
| Clock frequency Data Transfer Mode (default) | fPP | 25 | MHz | Default mode, CL=30pF | 22 | ||
| Clock frequency Identification Mode | fOD | 0 | 100 | 400 | KHz | Default mode, CL=30pF | 22 |
| Clock low time (default) | tWL | 10 | ns | Default mode | 22 | ||
| Clock high time (default) | tWH | 10 | ns | Default mode | 22 | ||
| Clock rise time (default) | tTLH | 10 | ns | Default mode | 22 | ||
| Clock fall time (default) | tTHL | 10 | ns | Default mode | 22 | ||
| Input setup time (default) | tISU | 5 | ns | Default mode | 22 | ||
| Input hold time (default) | tIH | 5 | ns | Default mode | 22 | ||
| Output delay time during Data Transfer Mode (default) | tODLY | 0 | 14 | ns | Default mode | 22 | |
| Output delay time during Identification Mode | tODLY | 0 | 50 | ns | Default mode | 22 | |
| Clock frequency Data Transfer Mode (high-speed) | fPP | 50 | MHz | High-speed mode, CL=30pF | 24 | ||
| Clock low time (high-speed) | tWL | 7 | ns | High-speed mode | 24 | ||
| Clock high time (high-speed) | tWH | 7 | ns | High-speed mode | 24 | ||
| Clock rise time (high-speed) | tTLH | 3 | ns | High-speed mode | 24 | ||
| Clock fall time (high-speed) | tTHL | 3 | ns | High-speed mode | 24 | ||
| Input setup time (high-speed) | tISU | 6 | ns | High-speed mode | 24 | ||
| Input hold time (high-speed) | tIH | 2 | ns | High-speed mode | 24 | ||
| Output delay time during Data Transfer Mode (high-speed) | tODLY | 0 | 14 | ns | High-speed mode | 24 | |
| Output Hold time | tOH | 2.5 | ns | High-speed mode | 24 | ||
| Total system capacitance for each line (high-speed) | CL | 40 | pF | High-speed mode | 24 |
CAD (KiCad official)
- Symbol:
XTSDQ01GWSIGA - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
xtsdq01gwsiga-etched.step/xtsdq01gwsiga-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xtsdq01gwsiga.step/xtsdq01gwsiga.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XTX datasheet (28 pp, sha256
142239cf2c5e274e, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XTSDQ01GWSIGA
**XTX** · NAND FLASH · WSON-8-EP(6x8)
XTSDQ01GWSIGA from XTX, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DAT2 | bidirectional | SD mode Data Line [bit2], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode. |
| 2 | DAT3/CD | bidirectional | SD mode Data Line [bit3] / SD NAND detection (internal 10-90 kOhm pull-up that may be used for card detection), input on power up; Chip Select input in SPI mode. |
| 3 | CLK | input | Clock input in both SD and SPI modes, up to 50MHz in high speed mode and 25MHz in default mode. |
| 4 | VSS | power_in | Ground supply in both SD and SPI modes. |
| 5 | CMD | bidirectional | Command/Response push-pull line in SD mode (10-100 kOhm pull-up recommended to prevent bus floating); Data In input in SPI mode. |
| 6 | DAT0 | bidirectional | SD mode Data Line [bit0], push-pull I/O; Data Out push-pull output in SPI mode. |
| 7 | DAT1 | bidirectional | SD mode Data Line [bit1], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode. |
| 8 | VDD | power_in | Supply voltage of 1.7V to 1.95V for the XTSDQ series (absolute maximum 2.25V), with max 5uF capacitance on the supply line and 45uF decoupling recommended. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XTX |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 1.7 | | 1.95 | V | TA=-40°C to 85°C | 19 |
| Input Leakage Current | ILI | -2 | | 2 | µA | | 19 |
| Output Leakage Current | ILO | -2 | | 2 | µA | | 19 |
| Standby Current | ICC1 | | 130 | 2500 | µA | VDD=1.95V | 19 |
| Read Current | ICC2 | | 32 | 75 | mA | FCLK=50MHz | 19 |
| Write Current | ICC2 | | 32 | 75 | mA | FCLK=50MHz | 19 |
| Input Low Voltage | VIL | -0.3 | | | V | | 19 |
| Output Low Voltage | VOL | | | 0.4 | V | IOL = 2mA | 19 |
| Operating Temperature | | -40 | | 85 | °C | | 16 |
| Storage Temperature | | -55 | | 125 | °C | | 16 |
| VDD (XTSDQ0x Series) | VDD | -0.3 | | 2.25 | V | | 16 |
| Voltage on I/O Pin with Respect to Ground (XTSDQ0x Series) | | -0.3 | | 2.25 | V | -0.3V to VDD+0.3 (<= 2.25V) | 16 |
| Total bus capacitance for each signal line | CL | | | 40 | pF | CHOST+CBUS <= 30pF | 16 |
| Single card capacitance | CCARD | | | 10 | pF | | 16 |
| Pull-up resistance | RCMD | 10 | | 100 | K Ohm | Prevent bus floating | 16 |
| Maximum signal line inductance | | | | 16 | nH | fPP <= 20MHz | 16 |
| Pull-up resistance inside card(pin1) | RDAT3 | 10 | | 90 | K Ohm | May be used for card detection | 16 |
| Capacity connected to power line | CC | | | 5 | uF | To prevent inrush current | 16 |
| Clock frequency Data Transfer Mode (default) | fPP | | | 25 | MHz | Default mode, CL=30pF | 22 |
| Clock frequency Identification Mode | fOD | 0 | 100 | 400 | KHz | Default mode, CL=30pF | 22 |
| Clock low time (default) | tWL | 10 | | | ns | Default mode | 22 |
| Clock high time (default) | tWH | 10 | | | ns | Default mode | 22 |
| Clock rise time (default) | tTLH | | | 10 | ns | Default mode | 22 |
| Clock fall time (default) | tTHL | | | 10 | ns | Default mode | 22 |
| Input setup time (default) | tISU | 5 | | | ns | Default mode | 22 |
| Input hold time (default) | tIH | 5 | | | ns | Default mode | 22 |
| Output delay time during Data Transfer Mode (default) | tODLY | 0 | | 14 | ns | Default mode | 22 |
| Output delay time during Identification Mode | tODLY | 0 | | 50 | ns | Default mode | 22 |
| Clock frequency Data Transfer Mode (high-speed) | fPP | | | 50 | MHz | High-speed mode, CL=30pF | 24 |
| Clock low time (high-speed) | tWL | 7 | | | ns | High-speed mode | 24 |
| Clock high time (high-speed) | tWH | 7 | | | ns | High-speed mode | 24 |
| Clock rise time (high-speed) | tTLH | | | 3 | ns | High-speed mode | 24 |
| Clock fall time (high-speed) | tTHL | | | 3 | ns | High-speed mode | 24 |
| Input setup time (high-speed) | tISU | 6 | | | ns | High-speed mode | 24 |
| Input hold time (high-speed) | tIH | 2 | | | ns | High-speed mode | 24 |
| Output delay time during Data Transfer Mode (high-speed) | tODLY | 0 | | 14 | ns | High-speed mode | 24 |
| Output Hold time | tOH | 2.5 | | | ns | High-speed mode | 24 |
| Total system capacitance for each line (high-speed) | CL | | | 40 | pF | High-speed mode | 24 |
## CAD (KiCad official)
- Symbol: `XTSDQ01GWSIGA`
- Footprint: `Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm`
- 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `xtsdq01gwsiga-etched.step` / `xtsdq01gwsiga-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xtsdq01gwsiga.step` / `xtsdq01gwsiga.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [XTX datasheet](docs/xtsdq01gwsiga-datasheet.pdf) (28 pp, sha256 `142239cf2c5e274e`, retrieved 2026-10-22, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xtsdq01gwsiga-datasheet.pdf)