component
XR2682
Public Made by Adomby adom
XySemi DC-DC Converters, ESOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXR2682
XySemi · DC-DC Converters · ESOP-8
XR2682 from XySemi, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch pin of the integrated 6A, 40mΩ boost power switch; the absolute maximum SW voltage is -0.3 to 26V. |
| 2 | SW | output | Switch pin of the integrated 6A, 40mΩ boost power switch (second switch-node pin, bonded in parallel with pin 1); the absolute maximum SW voltage is -0.3 to 26V. |
| 3 | PVDD | power_in | Input power supply pin, to be connected to Cin placed as close as possible to the pin; supply voltage range is 2.7 to 5.5V with absolute maximum VIN of -0.3 to 6.5V. |
| 4 | AVDD | power_in | Boost IC logic power supply pin; if located far from Cin, add one 1uF MLCC placed close to the pin. |
| 5 | EN | input | Shutdown control input; connect to a logic high level to enable the device, with an enable threshold of 0.3 to 1.5V (typ. 1V). |
| 6 | FB | input | Feedback pin for the internal resistor divider; regulated feedback voltage is 1.21 to 1.27V (typ. 1.24V), and the FB network should be placed close to the load and far from the switching node. |
| 7 | AGND | power_in | Analog ground; should be tied together with PGND and the exposed pad through a broad ground plane. |
| 8 | PGND | power_in | Power ground; should be connected to AGND and the exposed pad with low resistance for low Rds(on), high efficiency and good heat dissipation. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XySemi |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 2.7 | 5.5 | V | 4 | ||
| Boost output voltage range | Vout | 24 | V | 4 | |||
| Operating Supply Current | ISUPPLY | 100 | µA | VFB =1.5V, EN=Vin, ILoad =0 | 4 | ||
| Shutdown Supply Current | 1 | µA | VEN =0V, VIN =3.6V | 4 | |||
| Regulated Feedback Voltage | VFB | 1.21 | 1.24 | 1.27 | V | 4 | |
| Peak Inductor Current | IPEAK | 6 | A | 4 | |||
| Oscillator Frequency | FOSC | 400 | 600 | 800 | KHz | 4 | |
| Enable Threshold | 0.3 | 1 | 1.5 | V | VIN = 2.7V to 5.5V | 4 | |
| Enable Leakage Current | -0.1 | 0.1 | µA | 4 | |||
| SW Leakage Current | 1 | uA | VEN = 0V, VSW = 0V or 5V, VIN = 5V | 4 | |||
| Supply Voltage | VIN | -0.3 | 6.5 | V | 4 | ||
| FB, EN Voltage | -0.3 | 6.5 | V | 4 | |||
| SW Voltage | -0.3 | 26 | V | 4 | |||
| Operating Ambient Temperature | -40 | 85 | °C | 4 | |||
| Maximum Junction Temperature | 150 | °C | 4 | ||||
| Storage Temperature | -55 | 150 | °C | 4 | |||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 4 | |||
| Rds(ON) of N-channel FET | Rds(ON) | 40 | mΩ | ISW =1A | 4 | ||
| UVLO Low Threshold | VUVLOL | 2.6 | V | 4 | |||
| UVLO High Threshold | VUVLOH | 3.2 | V | 4 | |||
| Thermal shutdown threshold | 150 | ℃ | 6 | ||||
| Thermal shutdown restart temperature | 136 | ℃ | 6 |
CAD (KiCad official)
- Symbol:
XR2682 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
xr2682-etched.step/xr2682-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xr2682.step/xr2682.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XySemi datasheet (11 pp, sha256
0fceac6eff1d1da0, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).