component
XR16L580IM-F
Public Made by Adomby adom
MaxLinear UART, TQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
XR16L580IM-F
MaxLinear · UART · TQFP-48(7x7)
XR16L580IM-F from MaxLinear, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | 16/68# | input | Intel (logic 1) or Motorola (logic 0) bus select, with an internal pull-up resistor in the 48-TQFP package. |
| 2 | D5 | bidirectional | Data bus line 5 (bidirectional). |
| 3 | D6 | bidirectional | Data bus line 6 (bidirectional). |
| 4 | D7 | bidirectional | Data bus line 7 (bidirectional). |
| 5 | NC | unconnected | No connect. |
| 6 | NC | unconnected | No connect. |
| 7 | RX | input | UART receive data or infrared receive data; normal receive data input must idle at logic 1, the infrared receiver idles at logic 0. |
| 8 | TX | output | UART transmit data or infrared encoder data, logic 1 during reset or idle in standard mode; leave unconnected if not used. |
| 9 | NC | unconnected | No connect. |
| 10 | NC | unconnected | No connect. |
| 11 | CS# | input | Chip select input (active low) to enable the device. |
| 12 | NC | unconnected | No connect. |
| 13 | PwrSave | input | Power-Save input (active high) isolating the data bus interface from the host during sleep mode, with an internal pull-down resistor in the 48-TQFP package. |
| 14 | XTAL1 | input | Crystal or external clock input; not 5V tolerant, so the maximum voltage should be VCC. |
| 15 | XTAL2 | output | Crystal or buffered clock output that may drive a clock buffer for other devices. |
| 16 | IOW# | input | Intel mode (16/68# = 1): write strobe (active low); Motorola mode (16/68# = 0): R/W# read (logic 1) and write (logic 0) signal. |
| 17 | NC | unconnected | No connect. |
| 18 | GND | power_in | Power supply common, ground. |
| 19 | IOR# | input | Intel mode (16/68# = 1): read strobe (active low); in Motorola mode (16/68# = 0) this input is not used (NC). |
| 20 | NC | unconnected | No connect. |
| 21 | NC | unconnected | No connect. |
| 22 | NC | unconnected | No connect. |
| 23 | NC | unconnected | No connect. |
| 24 | NC | unconnected | No connect. |
| 25 | NC | unconnected | No connect. |
| 26 | A2 | input | Address line 2, selecting one of the internal registers during a data bus transaction. |
| 27 | A1 | input | Address line 1, selecting one of the internal registers during a data bus transaction. |
| 28 | A0 | input | Address line 0, selecting one of the internal registers during a data bus transaction. |
| 29 | NC | unconnected | No connect. |
| 30 | INT | output | Intel mode: active-high interrupt output, three-state when MCR[3]=0; Motorola mode: IRQ# active-low open-drain interrupt output requiring an external pull-up resistor. |
| 31 | NC | unconnected | No connect. |
| 32 | RTS# | output | UART request-to-send (active low) or general purpose output, used for auto RTS flow control. |
| 33 | DTR# | output | UART data-terminal-ready (active low) or general purpose output. |
| 34 | NC | unconnected | No connect. |
| 35 | RESET | input | Reset input, active high (RESET) in Intel mode and active low (RESET#) in Motorola mode, requiring a 40 ns minimum active pulse. |
| 36 | NC | unconnected | No connect. |
| 37 | NC | unconnected | No connect. |
| 38 | CTS# | input | UART clear-to-send (active low) or general purpose input for auto CTS flow control; connect to VCC when not used. |
| 39 | DSR# | input | UART data-set-ready (active low) or general purpose input; connect to VCC when not used. |
| 40 | CD# | input | UART carrier-detect (active low) or general purpose input; connect to VCC when not used. |
| 41 | RI# | input | UART ring-indicator (active low) or general purpose input; connect to VCC when not used. |
| 42 | VCC | power_in | 2.25V to 5.5V power supply; all input pins except XTAL1 are 5V tolerant. |
| 43 | D0 | bidirectional | Data bus line 0 (bidirectional). |
| 44 | D1 | bidirectional | Data bus line 1 (bidirectional). |
| 45 | D2 | bidirectional | Data bus line 2 (bidirectional). |
| 46 | D3 | bidirectional | Data bus line 3 (bidirectional). |
| 47 | D4 | bidirectional | Data bus line 4 (bidirectional). |
| 48 | NC | unconnected | No connect. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TQFP-48(7x7) |
| Category | Interface ICs |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Clock Input Low Level (2.5V column) | VILCK | -0.3 | 0.6 | V | 2.5V column | 38 | |
| Clock Input Low Level (3.3V column) | VILCK | -0.3 | 0.6 | V | 3.3V column | 38 | |
| Clock Input Low Level (5.0V column) | VILCK | -0.5 | 0.6 | V | 5.0V column | 38 | |
| Clock Input High Level (2.5V column) | VIHCK | 1.8 | V | 2.5V column | 38 | ||
| Clock Input High Level (3.3V column) | VIHCK | 2.4 | V | 3.3V column | 38 | ||
| Clock Input High Level (5.0V column) | VIHCK | 3 | V | 5.0V column | 38 | ||
| Input Low Voltage (2.5V column) | VIL | -0.3 | 0.5 | V | 2.5V column | 38 | |
| Input Low Voltage (3.3V column) | VIL | -0.3 | 0.8 | V | 3.3V column | 38 | |
| Input Low Voltage (5.0V column) | VIL | -0.5 | 0.8 | V | 5.0V column | 38 | |
| Input High Voltage (2.5V column) | VIH | 1.8 | 5.5 | V | 2.5V column | 38 | |
| Input High Voltage (3.3V column) | VIH | 2 | 5.5 | V | 3.3V column | 38 | |
| Input High Voltage (5.0V column) | VIH | 2.2 | 5.5 | V | 5.0V column | 38 | |
| Output Low Voltage | VOL | 0.4 | V | IOL = 6 mA | 38 | ||
| Output High Voltage | VOH | 1.8 | V | IOH = -6 mA | 38 | ||
| Output High Voltage | VOH | 2 | V | IOH = -1 mA | 38 | ||
| Output High Voltage | VOH | 2.4 | V | IOH = -400 uA | 38 | ||
| Input Low Leakage Current | IIL | -10 | 10 | uA | See Test 1A | 38 | |
| Input High Leakage Current | IIH | -10 | 10 | uA | See Test 1B | 38 | |
| Input Low Leakage Current, 16/68# pin (48-TQFP only) | IIL | -80 | uA | 48-TQFP; 16/68# pin internal pull-up; Test 1A | 38 | ||
| Input High Leakage Current, PwrSave pin (48-TQFP only) | IIH | 80 | uA | 48-TQFP; PwrSave pin internal pull-down; Test 1B | 38 | ||
| Input Pin Capacitance | CIN | 5 | pF | 38 | |||
| Power Supply Current (2.5V column) | ICC | 1 | mA | 2.5V column | 38 | ||
| Power Supply Current (3.3V column) | ICC | 2 | mA | 3.3V column | 38 | ||
| Power Supply Current (5.0V column) | ICC | 3 | mA | 5.0V column | 38 | ||
| Sleep / Power-Save Current, 16 mode, 48-TQFP (2.5V column) | ISLEEP/IPWRSV | 65 | uA | 16 mode, 48-TQFP; See Test 2; 2.5V column | 38 | ||
| Sleep / Power-Save Current, 16 mode, 48-TQFP (3.3V column) | ISLEEP/IPWRSV | 90 | uA | 16 mode, 48-TQFP; See Test 2; 3.3V column | 38 | ||
| Sleep / Power-Save Current, 16 mode, 48-TQFP (5.0V column) | ISLEEP/IPWRSV | 150 | uA | 16 mode, 48-TQFP; See Test 2; 5.0V column | 38 | ||
| Sleep / Power-Save Current, 68 mode, 48-TQFP (2.5V column) | ISLEEP/IPWRSV | 130 | uA | 68 mode, 48-TQFP; See Test 2; 2.5V column | 38 | ||
| Sleep / Power-Save Current, 68 mode, 48-TQFP (3.3V column) | ISLEEP/IPWRSV | 180 | uA | 68 mode, 48-TQFP; See Test 2; 3.3V column | 38 | ||
| Sleep / Power-Save Current, 68 mode, 48-TQFP (5.0V column) | ISLEEP/IPWRSV | 300 | uA | 68 mode, 48-TQFP; See Test 2; 5.0V column | 38 | ||
| Supply Voltage (recommended operating range) | VCC | 2.25 | 5.5 | V | Industrial grade (-40 to +85 oC), 48-TQFP | 38 | |
| Power Supply Range | 7 | V | 37 | ||||
| Voltage at Any Pin | -0.3 | 7 | V | 37 | |||
| Operating Temperature | -40 | 85 | oC | 37 | |||
| Storage Temperature | -65 | 150 | oC | 37 | |||
| Package Dissipation | 500 | mW | 37 | ||||
| Thermal Resistance (48-TQFP) junction-to-ambient | theta-ja | 59 | oC/W | 48-TQFP; margin of error +/-15% | 37 | ||
| Thermal Resistance (48-TQFP) junction-to-case | theta-jc | 16 | oC/W | 48-TQFP; margin of error +/-15% | 37 | ||
| Crystal Frequency (5.0V) | - | 24 | MHz | 5.0V column; crystal | 39 | ||
| External Clock Frequency (5.0V) | OSC | 50 | MHz | 5.0V column; external clock | 39 | ||
| External Clock Low/High Time (5.0V) | CLK | 10 | ns | 5.0V column | 39 | ||
| Address Setup Time, 16 Mode (5.0V) | TAS | 10 | ns | 5.0V column | 39 | ||
| Address Hold Time, 16 Mode (5.0V) | TAH | 0 | ns | 5.0V column | 39 | ||
| Chip Select Width, 16 Mode (5.0V) | TCS | 30 | ns | 5.0V column | 39 | ||
| IOR# Strobe Width, 16 Mode (5.0V) | TRD | 30 | ns | 5.0V column | 39 | ||
| Read Cycle Delay, 16 Mode (5.0V) | TDY | 30 | ns | 5.0V column | 39 | ||
| Data Access Time, 16 Mode (5.0V) | TRDV | 25 | ns | 5.0V column | 39 | ||
| Data Disable Time, 16 Mode (5.0V) | TDD | 0 | 20 | ns | 5.0V column | 39 | |
| IOW# Strobe Width, 16 Mode (5.0V) | TWR | 30 | ns | 5.0V column | 39 | ||
| Data Setup Time, 16 Mode (5.0V) | TDS | 12 | ns | 5.0V column | 39 | ||
| Data Hold Time, 16 Mode (5.0V) | TDH | 5 | ns | 5.0V column | 39 | ||
| Address Setup (68 Mode) (5.0V) | TADS | 10 | ns | 5.0V column | 39 | ||
| Address Hold (68 Mode) (5.0V) | TADH | 0 | ns | 5.0V column | 39 | ||
| R/W# Setup to CS# (68 Mode) (5.0V) | TRWS | 10 | ns | 5.0V column | 39 | ||
| Read Data Access (68 mode) (5.0V) | TRDA | 25 | ns | 5.0V column | 39 | ||
| Write Data Setup (68 mode) (5.0V) | TWDS | 12 | ns | 5.0V column | 39 | ||
| Delay From IOW# To Output (5.0V) | TWDO | 50 | ns | 5.0V column | 39 | ||
| Reset Pulse Width (5.0V) | TRST | 40 | ns | 5.0V column | 40 |
CAD (KiCad official)
- Symbol:
XR16L580IM-F - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
xr16l580im-f-etched.step/xr16l580im-f-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xr16l580im-f.step/xr16l580im-f.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (49 pp, sha256
ddf35df69cecb657, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).