component
XMC8P53S6
Public Made by Adomby adom
Shenzhen Fuman Microcontrollers (MCU/MPU/SOC), SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXMC8P53S6
Shenzhen Fuman · Microcontrollers (MCU/MPU/SOC) · SOT-23-6
XMC8P53S6 from Shenzhen Fuman, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P61/SCL | bidirectional | General-purpose bidirectional I/O with programmable pull-up/pull-down (pull-down available on P60-P62) or open-drain output, forced to SCL in test mode, and a pin change can wake the MCU from sleep. |
| 2 | VSS | power_in | Negative power supply (ground) pin, the 0 V reference for VDD. |
| 3 | P62/TCC/CLK_OUT/CLK_TEST | bidirectional | General-purpose bidirectional I/O that can be reused as the external TCC input, as the internal RC clock output (divide-by-2), or as a clock test pin, with programmable pull-up/pull-down or open-drain and sleep wake-up on pin change. |
| 4 | P63/RESET_N/VPP | bidirectional | General-purpose bidirectional I/O that can be reused as an active-low external RESET_N pin (internal pull-up forced on) or as the OTP_VPP input in test mode, and is open-drain when configured as an output. |
| 5 | VDD | power_in | Positive power supply pin; recommended operating range is 2 V to 5 V, must not exceed the 5.5 V limit, and requires a 0.1 µF decoupling capacitor (a 100 Ω series resistor is required when operating above 4 V). |
| 6 | P60/INT/SDA | bidirectional | General-purpose bidirectional I/O that can be reused as the external interrupt INT (rising or falling edge selectable), forced to SDA in test mode, with programmable pull-up/pull-down or open-drain and sleep wake-up on pin change. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Shenzhen Fuman |
| Package | SOT-23-6 |
| Category | Embedded Processors & Controllers |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 结温 TJ (absolute maximum) | TJ | -40 | 125 | ℃ | 4 | ||
| 存储温度 (storage temperature) | TSTG | -65 | 150 | ℃ | 4 | ||
| 工作电压 (operating voltage, absolute maximum table) | VDD | 2 | 5.5 | V | 4 | ||
| 工作频率 (operating frequency, absolute maximum table) | 16 | MHz | 4 | ||||
| ESD 人体模型 (HBM) | VESDHBM | -2500 | 2500 | V | 人体模型 (HBM) | 4 | |
| 结温 TJ (recommended) | TJ | -40 | 85 | ℃ | 4 | ||
| 工作电压 (recommended) | VDD | 2 | 5 | V | 4 | ||
| 工作频率 (recommended) | 16 | MHz | 4 | ||||
| 工作电流 (features: 16MHz) | 3.5 | mA | 5V/16MHz | 1 | |||
| 工作电流 (features: 8MHz) | 2 | mA | 5V/8MHz | 1 | |||
| 工作电流 (features: 4MHz) | 1.5 | mA | 5V/4MHz | 1 | |||
| 工作电流 (features: 1MHz) | 1 | mA | 5V/1MHz | 1 | |||
| 内部高频RC振荡器频率范围 | FIRC | 0.455 | 16 | MHz | 5 | ||
| 输入引脚输入漏电流 | IILKG | -1 | 1 | uA | VIN=VDD/VSS | 5 | |
| 输入高电压 施密特触发 VDD=3V | VIH2 | 1.2 | V | 施密特触发，VDD=3V | 5 | ||
| 输入高电压 施密特触发 VDD=5V | VIH2 | 1.5 | V | 施密特触发，VDD=5V | 5 | ||
| 输入低电压 施密特触发 VDD=3V | VIL2 | 0.6 | V | 施密特触发，VDD=3V | 5 | ||
| 输入低电压 施密特触发 VDD=5V | VIL2 | 1 | V | 施密特触发，VDD=5V | 5 | ||
| IRC 频率偏移 温度 | -1 | 1 | % | 16 MHz IRC, 温度 | 1 | ||
| IRC 频率偏移 电压 | -1.5 | 1.5 | % | 16 MHz IRC, 电压 | 1 | ||
| IRC 频率偏移 制程 | -0.5 | 0.5 | % | 16 MHz IRC, 制程 | 1 | ||
| IRC 频率偏移 总计 | -2.5 | 2.5 | % | 16 MHz IRC, 总计 | 1 | ||
| 输出 source 电流 IOH1 VDD=3V | IOH1 | 8 | mA | Vop=VDD-0.6V，VDD=3V | 5 | ||
| 输出 source 电流 IOH1 VDD=5V | IOH1 | 12 | mA | Vop=VDD-0.6V，VDD=5V | 5 | ||
| 输出 source 电流 IOH2 VDD=3V | IOH2 | 4 | mA | Vop=VDD-0.6V，VDD=3V | 5 | ||
| 输出 source 电流 IOH2 VDD=5V | IOH2 | 6 | mA | Vop=VDD-0.6V，VDD=5V | 5 | ||
| 输出 sink 电流 IOL1 VDD=3V | IOL1 | 18 | mA | Vop=VSS+0.6V，VDD=3V | 5 | ||
| 输出 sink 电流 IOL1 VDD=5V | IOL1 | 28 | mA | Vop=VSS+0.6V，VDD=5V | 5 | ||
| 输出 sink 电流 IOL2 VDD=3V | IOL2 | 9 | mA | Vop=VSS+0.6V，VDD=3V | 5 | ||
| 输出 sink 电流 IOL2 VDD=5V | IOL2 | 14 | mA | Vop=VSS+0.6V，VDD=5V | 5 | ||
| 输入上拉电流 IPH VDD=3V | IPH | 80 | uA | Input pin, VDD=3V | 5 | ||
| 输入上拉电流 IPH VDD=5V | IPH | 130 | uA | Input pin, VDD=5V | 5 | ||
| 输入下拉电流 IPL VDD=3V | IPL | 50 | uA | Input pin, VDD=3V | 5 | ||
| 输入下拉电流 IPL VDD=5V | IPL | 90 | uA | Input pin, VDD=5V | 5 | ||
| 省电电流 ISB1 | ISB1 | 1 | uA | 所有输入引脚接 VDD，输出引脚悬空，WDT/LVR/IRC 禁止 | 5 | ||
| 省电电流 ISB2 VDD=3V | ISB2 | 1 | uA | 所有输入引脚接 VDD，输出引脚悬空，LVR 使能，WDT /IRC 禁止,VDD=3V | 5 | ||
| 省电电流 ISB2 VDD=5V | ISB2 | 2.5 | uA | 所有输入引脚接 VDD，输出引脚悬空，LVR 使能，WDT /IRC 禁止,VDD=5V | 5 | ||
| 省电电流 ISB3 VDD=3V | ISB3 | 2.5 | uA | 所有输入引脚接 VDD，输出引脚悬空，WDT/LVR 使能，IRC 禁止，VDD=3V | 6 | ||
| 省电电流 ISB3 VDD=5V | ISB3 | 4.5 | uA | 所有输入引脚接 VDD，输出引脚悬空，WDT/LVR 使能，IRC 禁止，VDD=5V | 6 | ||
| 休眠模式电流 (典型值) | 1 | uA | 休眠模式 | 1 |
CAD (KiCad official)
- Symbol:
XMC8P53S6 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
xmc8p53s6-etched.step/xmc8p53s6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xmc8p53s6.step/xmc8p53s6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Shenzhen Fuman datasheet (22 pp, sha256
37c9867a11510c48, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).