main
History Download
Ray Publish 0.1.0 d27717c

XL3846

XINLUDA · AC-DC Controllers & Regulators · SOP-16-300mil

XL3846 from XINLUDA, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 C/S SS input Current limit/soft-start programming input; sink current is limited to 40 mA absolute maximum and current into this pin latches the shutdown state.
2 VREF power_out 5.1-V reference voltage output, requiring a 1 to 2.2 µF external capacitor and limited to 25 mA output current.
3 C/S- input Current sense comparator inverting input, with a common mode range of 0 to VIN-3 V.
4 C/S+ input Current sense comparator non-inverting input, with a common mode range of 0 to VIN-3 V and a maximum differential input of about 1.2 V versus pin 3.
5 E/A+ input Error amplifier non-inverting input, with a common mode range of 0 to VIN-2 V.
6 E/A- input Error amplifier inverting input, with a common mode range of 0 to VIN-2 V.
7 COMP bidirectional Error amplifier output and input to the PWM comparator, limited to 5 mA output current.
8 CT input Oscillator frequency programming capacitor pin, connected to the timing capacitor CT to GND.
9 RT input Oscillator frequency programming resistor pin, connected to the timing resistor RT to GND, with 5 mA maximum charging current.
10 SYNC bidirectional Synchronization output from the master controller or input of a slave controller, with sync input thresholds of 3.9 V high and 2.5 V low.
11 A Out output PWM drive signal output A, a totem-pole output rated 400 mA peak source or sink, complementary to pin 14.
12 GND power_in Ground; all signals are referenced to this node.
13 VC power_in Bias supply input for the output stage, 36 V absolute maximum and 30 V collector-emitter rating.
14 B Out output PWM drive signal output B, a totem-pole output rated 400 mA peak source or sink, complementary to pin 11.
15 VIN power_in Bias supply input, 36 V absolute maximum, with undervoltage lockout and a low-ESR decoupling capacitor to GND recommended.
16 Shutdown input External shutdown signal input; a signal above the 350 mV threshold (250 to 400 mV) fires the shutdown latch, with input range 0 to VIN.

Key specifications

Parameter Value
Manufacturer XINLUDA
Package SOP-16-300mil
Category Power Management ICs
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (Pin 15) 36 V 4
Collector Supply Voltage (Pin 13) 36 V 4
Output Current, Source or Sink (Pins 11, 14) 400 mA 4
Analog Inputs (Pins 3, 4, 5, 6, 16) -0.3 V 4
Reference Output Current (Pin 2) -25 mA 4
Sync Output Current (Pin 10) -5 mA 4
Error Amplifier Output Current (Pin 7) -5 mA 4
Soft Start Sink Current (Pin 1) -40 mA 4
Oscillator Charging Current (Pin 9) 5 mA 4
Power Dissipation at TA = 25°C 800 mW TA = 25°C 4
Power Dissipation at TC = 25°C 1500 mW TC = 25°C 4
Storage Temperature Tstg -65 150 °C 4
VREF terminal external capacitance 1 2.2 µF 4
Junction-to-ambient thermal resistance (SOP16(W)) RθJA 80 °C/W 4
Junction-to-case (top) thermal resistance (SOP16(W)) RθJC(top) 38 °C/W 4
Junction-to-board thermal resistance (SOP16(W)) RθJB 42 °C/W 4
Junction-to-top characterization parameter (SOP16(W)) ψJT 9 °C/W 4
Junction-to-board characterization parameter (SOP16(W)) ψJB 43 °C/W 4
Output Voltage 4.85 5.1 5.35 V TJ = 25°C, IO = 1 mA 5
Line Regulation 5 30 mV VIN = 8 V to 36 V 5
Load Regulation 3 20 mV IL = 1 mA to 10 mA 5
Total Output Variation 4.75 5.5 V Line, Load, and Temperature 5
Short Circuit Output Current -35 -10 mA VREF = 0 V 5
Oscillator Initial Accuracy 34 43 51 kHz TJ = 25°C 5
Oscillator Voltage Stability -1 3 % VIN = 8 V to 36 V 5
Oscillator Temperature Stability -2 % Over operating range 5
Sync Output High Level 3.9 4.35 V 5
Sync Output Low Level 2.3 2.5 V 5
Sync Input High Level 3.9 V Pin 8 = 0 V 5
Sync Input Low Level 2.5 V Pin 8 = 0 V 5
Sync Input Current 1.3 1.5 mA Sync Voltage = 3.9 V, Pin 8 = 0 V 5
Error Amplifier Input Offset Voltage 0.5 20 mV 5
Error Amplifier Input Bias Current -2 -0.6 µA 5
Error Amplifier Input Offset Current 40 250 nA 5
Error Amplifier Common Mode Range 0 V VIN = 8 V to 36 V 5
Error Amplifier Open Loop Voltage Gain 80 105 dB ΔVO = 1.2 to 3 V, VCM = 2 V 5
Error Amplifier Output Sink Current 2 6 mA VID = -15 mV to -5 V, VPIN7 = 1.2 V 5
Error Amplifier Output Source Current -0.5 -0.4 mA VID = 15 mV to -5 V, VPIN7 = 2.5 V 5
Error Amplifier High Level Output Voltage (Pin 7) 4.3 4.6 V RL = 15 kΩ 5
Error Amplifier Low Level Output Voltage (Pin 7) 0.7 1 V RL = 15 kΩ 5
Current Sense Amplifier Gain 2.4 2.75 3.2 V VPIN 3 = 0 V, Pin 1 Open 5
Maximum Differential Input Signal (VPIN 4-VPIN 3) 1.1 1.2 V Pin 1 Open; RL (Pin 7) = 15 kW 6
Current Sense Input Offset Voltage 5 25 mV VPIN 1 = 0.5 V, Pin 7 Open 6
Current Sense Input Bias Current -10 -2.5 µA VPIN 1 = 0.5 V, Pin 7 Open 6
Current Sense Input Common Mode Range 0 V 6
Current Sense Delay to Outputs 300 700 ns TJ = 25°C 6
Current Limit Offset 0.45 0.5 0.55 V VPIN 3 = 0 V, VPIN 4 = 0 V, Pin 7 Open 6
Current Limit Adjust Input Bias Current -30 -10 µA VPIN 5 = VREF, VPIN 6 = 0 V 6
Shutdown Threshold Voltage 250 350 400 mV 6
Shutdown Input Voltage Range 0 V 6
Minimum Latching Current (IPIN1) 1.5 3 mA 6
Maximum Latching Current (IPIN1) 0.8 1.5 mA 6
Output Collector-Emitter Voltage 30 V 6
Collector Leakage Current 200 µA VC = 30 V 6
Output Low Level 0.1 0.4 V ISINK = 20 mA 6
Output Low Level 0.4 2.1 V ISINK = 100 mA 6
Output High Level 13 13.5 V ISOURCE = 20 mA 6
Output High Level 12 13.5 V ISOURCE = 100 mA 6
Undervoltage Lockout Start-Up Threshold 7.7 8.2 V 6
Supply Current (Total Standby Current) 18 23 mA 6

CAD (KiCad official)

  • Symbol: XL3846
  • Footprint: Package_SO:SOIC-16W_7.5x12.8mm_P1.27mm
  • 3D model: SOP-16-300mil (KiCad packages3D, STEP)
  • 3D model files: xl3846-etched.step / xl3846-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); xl3846.step / xl3846.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: XINLUDA datasheet (16 pp, sha256 8ba1a5795314d686, retrieved 2026-11-13, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF