main
Ray
Publish 0.1.0
49d39e3
XL3232-TS
XINLUDA · RS232 ICs · TSSOP-16
XL3232-TS from XINLUDA, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1+ | passive | Positive lead of the C1 charge-pump capacitor (0.1 µF at 3.3 V; 0.047 µF at 5 V per the test conditions). |
| 2 | V+ | power_out | Positive charge-pump output for the storage capacitor only; the absolute maximum V+ is 7 V with respect to GND. |
| 3 | C1- | passive | Negative lead of the C1 charge-pump capacitor. |
| 4 | C2+ | passive | Positive lead of the C2 charge-pump capacitor (0.33 µF at 5 V per the test conditions). |
| 5 | C2- | passive | Negative lead of the C2 charge-pump capacitor. |
| 6 | V- | power_out | Negative charge-pump output for the storage capacitor only; the absolute maximum V- is -7 V with respect to GND. |
| 7 | DOUT2 | output | RS-232 line driver output to the remote RS-232 system, with outputs protected against shorts to ground and driver output limited to ±13.2 V. |
| 8 | RIN2 | input | RS-232 line receiver input from the remote system, rated for receiver input voltages of ±25 V. |
| 9 | ROUT2 | output | Logic-level receiver output to the UART; an open RIN input causes ROUT to go high. |
| 10 | DIN2 | input | Logic-level driver input from the UART that must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC). |
| 11 | DIN1 | input | Logic-level driver input from the UART that must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC). |
| 12 | ROUT1 | output | Logic-level receiver output to the UART; an open RIN input causes ROUT to go high. |
| 13 | RIN1 | input | RS-232 line receiver input from the remote system, rated for receiver input voltages of ±25 V. |
| 14 | DOUT1 | output | RS-232 line driver output to the remote RS-232 system, with outputs protected against shorts to ground and driver output limited to ±13.2 V. |
| 15 | GND | power_in | Ground reference; all voltages in the datasheet are referenced to network GND. |
| 16 | VCC | power_in | Supply voltage input, 3 V to 5.5 V (3.3 V or 5 V recommended). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | TSSOP-16 |
| Category | Interface |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply voltage, VCC = 3.3 V | VCC | 3 | 3.3 | 3.6 | V | VCC = 3.3 V | 5 |
| VCC Supply voltage, VCC = 5 V | VCC | 4.5 | 5 | 5.5 | V | VCC = 5 V | 5 |
| Driver high-level input voltage DIN | VIH | 2 | V | VCC = 3.3 V | 5 | ||
| Driver high-level input voltage DIN | VIH | 2.4 | V | VCC = 5 V | 5 | ||
| Driver low-level input voltage DIN | VIL | 0.8 | V | 5 | |||
| Driver input voltage DIN | VI | 0 | 5.5 | V | 5 | ||
| Receiver input voltage RIN | VI | -25 | 25 | V | 5 | ||
| Operating free-air temperature, XL3232-TS | TA | -40 | 85 | °C | XL3232-TS | 5 | |
| VCC Supply voltage | VCC | -0.3 | 6 | V | 4 | ||
| V+ Positive output supply voltage | V+ | -0.3 | 7 | V | 4 | ||
| V- Negative output supply voltage | V- | -7 | 0.3 | V | 4 | ||
| V+, V- Supply voltage difference | V+, V- | 13 | V | 4 | |||
| Input voltage, drivers | VI | -0.3 | 6 | V | Drivers | 4 | |
| Input voltage, receivers | VI | -25 | 25 | V | Receivers | 4 | |
| Output voltage, drivers | VO | -13.2 | 13.2 | V | Drivers | 4 | |
| Output voltage, receivers | VO | -0.3 | V | Receivers; upper limit printed as VCC + 0.3 V | 4 | ||
| Operating virtual junction temperature | TJ | 125 | °C | 4 | |||
| Storage temperature | Tstg | -45 | 150 | °C | 4 | ||
| Supply current | ICC | 0.5 | 10 | mA | No load, VCC = 3.3 V or 5 V | 5 | |
| DOUT high-level output voltage | VOH | 5 | 5.4 | V | RL = 3 kΩ to GND, DIN = GND | 5 | |
| DOUT low-level output voltage | VOL | -5.4 | -5 | V | RL = 3 kΩ to GND, DIN = VCC | 5 | |
| High-level input current | IIH | -1 | 0.01 | 1 | µA | VI = VCC | 5 |
| Low-level input current | IIL | -1 | 0.01 | 1 | µA | VI at GND | 5 |
| Short-circuit output current | IOS | -35 | 35 | mA | VCC = 3.6 V, VO = 0 V | 5 | |
| Short-circuit output current | IOS | -60 | 60 | mA | VCC = 5.5 V, VO = 0 V | 5 | |
| Output resistance | rO | 300 | Ω | VCC, V+, and V- = 0 V, VO = ±2 V | 5 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = 1.6 mA | 6 | ||
| Positive-going input threshold voltage | VIT+ | 1.5 | 2.4 | V | VCC = 3.3 V | 6 | |
| Positive-going input threshold voltage | VIT+ | 1.8 | 2.4 | V | VCC = 5 V | 6 | |
| Negative-going input threshold voltage | VIT- | 0.6 | 1.2 | V | VCC = 3.3 V | 6 | |
| Negative-going input threshold voltage | VIT- | 0.8 | 1.5 | V | VCC = 5 V | 6 | |
| Input hysteresis (VIT+, VIT-) | Vhys | 0.3 | V | 6 | |||
| Input resistance | ri | 3 | 5 | 7 | kΩ | VI = ±3 V to ±25 V | 6 |
| Maximum data rate | 150 | 250 | kbit/s | RL = 3 kΩ, one DOUT switching, CL = 1000 pF | 6 | ||
| Driver pulse skew | tsk(p) | 300 | ns | RL = 3 kΩ to 7 kΩ, CL = 150 pF to 2500 pF | 6 | ||
| Driver slew rate, transition region | SR(tr) | 6 | 30 | V/µs | RL = 3 kΩ to 7 kΩ, VCC = 3.3 V, CL = 150 pF to 1000 pF | 6 | |
| Driver slew rate, transition region | SR(tr) | 4 | 30 | V/µs | RL = 3 kΩ to 7 kΩ, VCC = 3.3 V, CL = 150 pF to 2500 pF | 6 | |
| Receiver propagation delay time, low- to high-level output | tPLH | 300 | ns | CL = 150 pF | 6 | ||
| Receiver propagation delay time, high- to low-level output | tPHL | 300 | ns | CL = 150 pF | 6 | ||
| Receiver pulse skew | tsk(p) | 300 | ns | 6 | |||
| Junction-to-ambient thermal resistance, TS (TSSOP) 16 pins | RθJA | 103.1 | °C/W | TS (TSSOP), 16 pins | 4 | ||
| Junction-to-case (top) thermal resistance, TS (TSSOP) 16 pins | RθJCtop | 49.2 | °C/W | TS (TSSOP), 16 pins | 4 | ||
| Junction-to-board thermal resistance, TS (TSSOP) 16 pins | RθJB | 54.8 | °C/W | TS (TSSOP), 16 pins | 4 | ||
| Junction-to-top characterization parameter, TS (TSSOP) 16 pins | ψJT | 12 | °C/W | TS (TSSOP), 16 pins | 4 | ||
| Junction-to-board characterization parameter, TS (TSSOP) 16 pins | ψJB | 54.1 | °C/W | TS (TSSOP), 16 pins | 4 |
CAD (KiCad official)
- Symbol:
XL3232-TS - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
xl3232-ts-etched.step/xl3232-ts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl3232-ts.step/xl3232-ts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (15 pp, sha256
746b01f367b01497, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XL3232-TS
**XINLUDA** · RS232 ICs · TSSOP-16
XL3232-TS from XINLUDA, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1+ | passive | Positive lead of the C1 charge-pump capacitor (0.1 µF at 3.3 V; 0.047 µF at 5 V per the test conditions). |
| 2 | V+ | power_out | Positive charge-pump output for the storage capacitor only; the absolute maximum V+ is 7 V with respect to GND. |
| 3 | C1- | passive | Negative lead of the C1 charge-pump capacitor. |
| 4 | C2+ | passive | Positive lead of the C2 charge-pump capacitor (0.33 µF at 5 V per the test conditions). |
| 5 | C2- | passive | Negative lead of the C2 charge-pump capacitor. |
| 6 | V- | power_out | Negative charge-pump output for the storage capacitor only; the absolute maximum V- is -7 V with respect to GND. |
| 7 | DOUT2 | output | RS-232 line driver output to the remote RS-232 system, with outputs protected against shorts to ground and driver output limited to ±13.2 V. |
| 8 | RIN2 | input | RS-232 line receiver input from the remote system, rated for receiver input voltages of ±25 V. |
| 9 | ROUT2 | output | Logic-level receiver output to the UART; an open RIN input causes ROUT to go high. |
| 10 | DIN2 | input | Logic-level driver input from the UART that must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC). |
| 11 | DIN1 | input | Logic-level driver input from the UART that must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC). |
| 12 | ROUT1 | output | Logic-level receiver output to the UART; an open RIN input causes ROUT to go high. |
| 13 | RIN1 | input | RS-232 line receiver input from the remote system, rated for receiver input voltages of ±25 V. |
| 14 | DOUT1 | output | RS-232 line driver output to the remote RS-232 system, with outputs protected against shorts to ground and driver output limited to ±13.2 V. |
| 15 | GND | power_in | Ground reference; all voltages in the datasheet are referenced to network GND. |
| 16 | VCC | power_in | Supply voltage input, 3 V to 5.5 V (3.3 V or 5 V recommended). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | TSSOP-16 |
| Category | Interface |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply voltage, VCC = 3.3 V | VCC | 3 | 3.3 | 3.6 | V | VCC = 3.3 V | 5 |
| VCC Supply voltage, VCC = 5 V | VCC | 4.5 | 5 | 5.5 | V | VCC = 5 V | 5 |
| Driver high-level input voltage DIN | VIH | 2 | | | V | VCC = 3.3 V | 5 |
| Driver high-level input voltage DIN | VIH | 2.4 | | | V | VCC = 5 V | 5 |
| Driver low-level input voltage DIN | VIL | | | 0.8 | V | | 5 |
| Driver input voltage DIN | VI | 0 | | 5.5 | V | | 5 |
| Receiver input voltage RIN | VI | -25 | | 25 | V | | 5 |
| Operating free-air temperature, XL3232-TS | TA | -40 | | 85 | °C | XL3232-TS | 5 |
| VCC Supply voltage | VCC | -0.3 | | 6 | V | | 4 |
| V+ Positive output supply voltage | V+ | -0.3 | | 7 | V | | 4 |
| V- Negative output supply voltage | V- | -7 | | 0.3 | V | | 4 |
| V+, V- Supply voltage difference | V+, V- | | | 13 | V | | 4 |
| Input voltage, drivers | VI | -0.3 | | 6 | V | Drivers | 4 |
| Input voltage, receivers | VI | -25 | | 25 | V | Receivers | 4 |
| Output voltage, drivers | VO | -13.2 | | 13.2 | V | Drivers | 4 |
| Output voltage, receivers | VO | -0.3 | | | V | Receivers; upper limit printed as VCC + 0.3 V | 4 |
| Operating virtual junction temperature | TJ | | | 125 | °C | | 4 |
| Storage temperature | Tstg | -45 | | 150 | °C | | 4 |
| Supply current | ICC | | 0.5 | 10 | mA | No load, VCC = 3.3 V or 5 V | 5 |
| DOUT high-level output voltage | VOH | 5 | 5.4 | | V | RL = 3 kΩ to GND, DIN = GND | 5 |
| DOUT low-level output voltage | VOL | | -5.4 | -5 | V | RL = 3 kΩ to GND, DIN = VCC | 5 |
| High-level input current | IIH | -1 | 0.01 | 1 | µA | VI = VCC | 5 |
| Low-level input current | IIL | -1 | 0.01 | 1 | µA | VI at GND | 5 |
| Short-circuit output current | IOS | -35 | | 35 | mA | VCC = 3.6 V, VO = 0 V | 5 |
| Short-circuit output current | IOS | -60 | | 60 | mA | VCC = 5.5 V, VO = 0 V | 5 |
| Output resistance | rO | 300 | | | Ω | VCC, V+, and V- = 0 V, VO = ±2 V | 5 |
| Low-level output voltage | VOL | | | 0.4 | V | IOL = 1.6 mA | 6 |
| Positive-going input threshold voltage | VIT+ | 1.5 | | 2.4 | V | VCC = 3.3 V | 6 |
| Positive-going input threshold voltage | VIT+ | 1.8 | | 2.4 | V | VCC = 5 V | 6 |
| Negative-going input threshold voltage | VIT- | 0.6 | | 1.2 | V | VCC = 3.3 V | 6 |
| Negative-going input threshold voltage | VIT- | 0.8 | | 1.5 | V | VCC = 5 V | 6 |
| Input hysteresis (VIT+, VIT-) | Vhys | | | 0.3 | V | | 6 |
| Input resistance | ri | 3 | 5 | 7 | kΩ | VI = ±3 V to ±25 V | 6 |
| Maximum data rate | | 150 | | 250 | kbit/s | RL = 3 kΩ, one DOUT switching, CL = 1000 pF | 6 |
| Driver pulse skew | tsk(p) | | | 300 | ns | RL = 3 kΩ to 7 kΩ, CL = 150 pF to 2500 pF | 6 |
| Driver slew rate, transition region | SR(tr) | 6 | | 30 | V/µs | RL = 3 kΩ to 7 kΩ, VCC = 3.3 V, CL = 150 pF to 1000 pF | 6 |
| Driver slew rate, transition region | SR(tr) | 4 | | 30 | V/µs | RL = 3 kΩ to 7 kΩ, VCC = 3.3 V, CL = 150 pF to 2500 pF | 6 |
| Receiver propagation delay time, low- to high-level output | tPLH | | | 300 | ns | CL = 150 pF | 6 |
| Receiver propagation delay time, high- to low-level output | tPHL | | | 300 | ns | CL = 150 pF | 6 |
| Receiver pulse skew | tsk(p) | | | 300 | ns | | 6 |
| Junction-to-ambient thermal resistance, TS (TSSOP) 16 pins | RθJA | | 103.1 | | °C/W | TS (TSSOP), 16 pins | 4 |
| Junction-to-case (top) thermal resistance, TS (TSSOP) 16 pins | RθJCtop | | 49.2 | | °C/W | TS (TSSOP), 16 pins | 4 |
| Junction-to-board thermal resistance, TS (TSSOP) 16 pins | RθJB | | 54.8 | | °C/W | TS (TSSOP), 16 pins | 4 |
| Junction-to-top characterization parameter, TS (TSSOP) 16 pins | ψJT | | 12 | | °C/W | TS (TSSOP), 16 pins | 4 |
| Junction-to-board characterization parameter, TS (TSSOP) 16 pins | ψJB | | 54.1 | | °C/W | TS (TSSOP), 16 pins | 4 |
## CAD (KiCad official)
- Symbol: `XL3232-TS`
- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`
- 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files: `xl3232-ts-etched.step` / `xl3232-ts-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xl3232-ts.step` / `xl3232-ts.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [XINLUDA datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603055940535140352) (15 pp, sha256 `746b01f367b01497`, retrieved 2026-10-18, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xl3232-ts-datasheet.pdf)