component
XL293-TS
Public Made by Adomby adom
XINLUDA Operational Amplifier, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXL293-TS
XINLUDA · Operational Amplifier · TSSOP-8
XL293-TS from XINLUDA, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | 1OUT | output | Open-drain NPN output of comparator 1 that sinks current when the IN+ voltage is above the IN- voltage plus offset; absolute maximum output current is 18 mA and output voltage is -0.3 V to 36 V. |
| 2 | 1IN- | input | Negative (inverting) input of comparator 1; it must not go below -0.3 V and should stay within 0 V to VCC-2 V. |
| 3 | 1IN+ | input | Positive (non-inverting) input of comparator 1; it must not go below -0.3 V and should stay within 0 V to VCC-2 V. |
| 4 | GND | power_in | Ground pin; all voltages except differential voltages are referenced to network ground. |
| 5 | 2IN+ | input | Positive (non-inverting) input of comparator 2; it must not go below -0.3 V and should stay within 0 V to VCC-2 V. |
| 6 | 2IN- | input | Negative (inverting) input of comparator 2; it must not go below -0.3 V and should stay within 0 V to VCC-2 V. |
| 7 | 2OUT | output | Open-drain NPN output of comparator 2 that sinks current when the IN+ voltage is above the IN- voltage plus offset; absolute maximum output current is 18 mA and output voltage is -0.3 V to 36 V. |
| 8 | VCC | power_in | Supply pin; recommended supply range is 2 V to 30 V (absolute maximum -0.3 V to 36 V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | TSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VCC | -0.3 | 36 | V | 4 | ||
| Differential input voltage | VID | -36 | 36 | V | 4 | ||
| Input pin voltage range | VIN | -0.3 | 36 | V | 4 | ||
| Output pin voltage range | VO | -0.3 | 36 | V | 4 | ||
| Output current | IO | 18 | mA | 4 | |||
| Operating virtual-junction temperature | Tj | 150 | ℃ | 4 | |||
| Storage temperature range | Tstg | -50 | 150 | ℃ | 4 | ||
| Supply voltage range (Vs = VCC - GND) | Vs | 2 | 30 | V | Over operating free-air temperature range | 4 | |
| Input pin voltage range | 0 | V | Over operating free-air temperature range; maximum printed as VCC-2 | 4 | |||
| Ambient temperature (293) | TA | -25 | 85 | °C | Over operating free-air temperature range | 4 | |
| Input offset voltage | VIO | 3 | 8 | mV | Vcc = 5 V to 30 V, 25°C | 5 | |
| Input offset voltage (full range) | VIO | 10 | mV | Vic = VICR min, Vo = 1.4 V, Full range | 5 | ||
| Input offset current | IIO | 7 | 100 | nA | Vo = 1.4 V, 25°C | 5 | |
| Input offset current (full range) | IIO | 300 | nA | Vo = 1.4 V, Full range | 5 | ||
| Input bias current | IIB | -30 | -300 | nA | Vo = 1.4V, 25°C | 5 | |
| Input bias current (full range) | IIB | -500 | nA | Vo = 1.4V, Full range | 5 | ||
| Common-mode input-voltage range | VICR | 0 | V | 5 | |||
| Common-mode input-voltage range (full range) | VICR | 0 | V | 5 | |||
| Large-signal differential-voltage amplification | AVD | 50 | 200 | V/mV | VCc = 15 V, Vo = 1.4 V to 11.4V, RL ≥ 15 kΩ to Vcc, 25°C | 5 | |
| High-level output current | IOH | 0.3 | 90 | nA | VOH = 5 V, VID = 1 V, 25°C | 5 | |
| High-level output current (full range) | IOH | 2 | uA | VOH = 30 V, VID = 1 V, Full range | 5 | ||
| Low-level output voltage | VOL | 150 | 450 | mV | IOL = 4 mA, VID = -1 V, 25°C | 5 | |
| Low-level output voltage (full range) | VOL | 750 | mV | IOL = 4 mA, VID = -1 V, Full range | 5 | ||
| Low-level output current | IOL | 3 | mA | VOL = 1.5 V, VID = -1 V, 25°C | 5 | ||
| Supply current | ICC | 0.8 | 2 | mA | RL = ∞, Vcc = 5 V, 25°C | 5 | |
| Supply current (full range) | ICC | 5 | mA | RL = ∞, Vcc = 30 V, Full range | 5 | ||
| Junction-to-ambient thermal resistance (TSSOP8) | RSJA | 205 | °c/w | Typical value | 4 | ||
| Junction-to-case (top) thermal resistance (TSSOP8) | Rejc(top) | 89 | °c/w | Typical value | 4 |
CAD (KiCad official)
- Symbol:
XL293-TS - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
xl293-ts-etched.step/xl293-ts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl293-ts.step/xl293-ts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (12 pp, sha256
684d00669bcd787d, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).