main
History Download
Ray Publish 0.1.0 98b3563

XL2515

XINLUDA · CAN ICs · SOP-18-300mil

XL2515 from XINLUDA, in a SOP-18-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TXCAN output Transmit output pin to the CAN bus.
2 RXCAN input Receive input pin from the CAN bus.
3 CLKOUT output Clock output pin with a programmable prescaler that divides FOSC by 1, 2, 4 or 8, with Start-of-Frame signal as the alternate function.
4 TX0RTS input Request-to-Send input for transmit buffer TXB0, or a general purpose digital input, with a 100 k internal pull-up to VDD.
5 TX1RTS input Request-to-Send input for transmit buffer TXB1, or a general purpose digital input, with a 100 k internal pull-up to VDD.
6 TX2RTS input Request-to-Send input for transmit buffer TXB2, or a general purpose digital input, with a 100 k internal pull-up to VDD.
7 OSC2 output Oscillator output for the crystal or ceramic resonator connected to OSC1 and OSC2.
8 OSC1 input Oscillator input, also usable as an external clock input.
9 VSS power_in Ground reference for logic and I/O pins.
10 RX1BF output Receive buffer RXB1 interrupt pin, or a general purpose digital output.
11 RX0BF output Receive buffer RXB0 interrupt pin, or a general purpose digital output.
12 INT output Interrupt output pin.
13 SCK input Clock input pin for the SPI interface.
14 SI input Data input pin for the SPI interface.
15 SO output Data output pin for the SPI interface.
16 CS input Chip select input pin for the SPI interface.
17 RESET input Active-low device Reset input.
18 VDD power_in Positive supply for logic and I/O pins; the device operates from 2.7 V to 5.5 V.

Key specifications

Parameter Value
Manufacturer XINLUDA
Package SOP-18-300mil
Category Interface ICs
Pins 18

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Power supply voltage (absolute maximum) VDD 6.5 V 69
All inputs and outputs w.r.t. Vss (absolute maximum, lower bound) VSS -0.6 V 69
Storage temperature TST -65 150 ℃ 69
Ambient temperature with power applied (Industrial column) TATPA -40 105 ℃ Industrial; printed as +105/125, Extended (Q) 125 ℃ not applicable to this MPN 69
Soldering temperature of leads TSTL 300 ℃ 10 seconds 69
Supply voltage VDD 2.7 5.5 V 70
Register retention voltage VRET 2.4 V 70
High-level input voltage, RXCAN pin (minimum) VIH 2 V 70
Low-level input voltage, RXCAN and TXnRTS pins (minimum) VIL -0.3 V 70
Low-level input voltage, SCK, CS, SI pins (minimum) VIL -0.3 V 70
Low-level output voltage, TXCAN pin VOL 0.6 V IOL = +6.0 mA, VDD = 4.5V 70
Low-level output voltage, RXnBF pin VOL 0.6 V IOL = +8.5 mA, VDD = 4.5V 70
Low-level output voltage, SO and CLKOUT pins VOL 0.6 V IOL = +2.1 mA, VDD = 4.5V 70
Low-level output voltage, INT pin VOL 0.6 V IOL = +1.6 mA, VDD = 4.5V 70
Input leakage current, all I/Os except OSC1 and TXnRTS pins ILI -1 1 µA CS = RESET = VDD, VIN = VSS to VDD 70
Input leakage current, OSC1 pin ILI -5 5 µA 70
Internal capacitance (all inputs and outputs) CINT 10 pF TAMB = +25°C, fC = 1.0 MHz, VDD = 0V (Note 1) 70
Operating current IDD 10 mA VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open 70
Standby current (Sleep mode), Industrial IDDS 5 µA CS, TXnRTS = VDD, inputs tied to VDD or VSS, -40°C to +85°C 70
Clock in frequency FOSC 1 40 MHz VDD = 4.5V to 5.5V 71
Clock in frequency FOSC 1 25 MHz VDD = 2.7V to 5.5V 71
Clock in period TOSC 25 1000 ns VDD = 4.5V to 5.5V 71
Clock in period TOSC 40 1000 ns VDD = 2.7V to 5.5V 71
Duty cycle (external clock input) TDUTY 0.45 0.55 TOSH/(TOSH + TOSL) external clock input 71
Wake-up noise filter TWF 100 ns 71
RESET pin low time tRL 10 µs 71
CLKOUT pin high time thCLKOUT 15 ns TOSC = 40 ns (Note 1) 72
CLKOUT pin low time tlCLKOUT 15 ns TOSC = 40 ns (Note 1) 72
CLKOUT pin rise time trCLKOUT 5 ns Measured from 0.3 VDD to 0.7 VDD (Note 1) 72
CLKOUT pin fall time tfCLKOUT 5 ns Measured from 0.7 VDD to 0.3 VDD (Note 1) 72
CLKOUT propagation delay tdCLKOUT 100 ns Note 1 72
Ambient temperature range (Industrial, ordering table) TAMB -40 105 ℃ XL2515 SOP18 Industrial, per ordering information 76
Clock frequency (SPI) FCLK 10 MHz 73
CS setup time TCSS 50 ns 73
CS hold time TCSH 50 ns 73
CS disable time TCSD 50 ns 73
Data setup time TSU 10 ns 73
Data hold time THD 10 ns 73
Clock rise time TR 2 µs Note 1 73
Clock fall time TF 2 µs Note 1 73
Clock high time THI 45 ns 73
Clock low time TLO 45 ns 73
Clock delay time TCLD 50 ns 73
Clock enable time TCLE 50 ns 73
Output valid from clock low TV 45 ns 73
Output hold time THO 0 ns 73
Output disable time TDIS 100 ns 73

CAD (KiCad official)

  • Symbol: XL2515
  • Footprint: Package_SO:SOP-18_7.495x11.515mm_P1.27mm
  • 3D model: SOP-18-300mil, generated on the KiCad land (body 7.49 x 11.53 mm, terminals on the pads, 2.5 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: xl2515-etched.step / xl2515-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); xl2515.step / xl2515.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: XINLUDA datasheet (76 pp, sha256 0034edeb9a204ca2, retrieved 2026-11-13, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF