Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

X95820UV14IZ-2.7

RENESAS · Digital Potentiometers · TSSOP-14

X95820UV14IZ-2.7 from RENESAS, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VCC power_in Power supply pin; the device operates from 2.7V to 5.5V.
2 WP input Active-low hardware write protection pin that prevents any Write operation of the I2C interface; it must be at logic HIGH to allow writes.
3 RH0 passive "High" terminal of DCP0; voltage at any DCP pin must stay between GND and VCC.
4 RL0 passive "Low" terminal of DCP0; voltage at any DCP pin must stay between GND and VCC.
5 RW0 passive "Wiper" terminal of DCP0; wiper current is limited to ±3.0mA and voltage must stay between GND and VCC.
6 A2 input Device address input for the I2C interface, which sets address bit A2 and must match the identification byte.
7 SCL input I2C interface clock input; the maximum SCL frequency is 400 kHz.
8 SDA bidirectional Serial data I/O for the I2C interface; its input buffer thresholds are 0.3VCC (low) and 0.7VCC (high), and it sinks 4mA with VOL up to 0.4V.
9 GND power_in Ground reference pin for the device.
10 RW1 passive "Wiper" terminal of DCP1; wiper current is limited to ±3.0mA and voltage must stay between GND and VCC.
11 RL1 passive "Low" terminal of DCP1; voltage at any DCP pin must stay between GND and VCC.
12 RH1 passive "High" terminal of DCP1; voltage at any DCP pin must stay between GND and VCC.
13 A0 input Device address input for the I2C interface, which sets address bit A0 and must match the identification byte.
14 A1 input Device address input for the I2C interface, which sets address bit A1 and must match the identification byte.

Key specifications

Parameter Value
Manufacturer RENESAS
Package TSSOP-14
Category Data Converters
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
RH to RL Resistance (RTOTAL), U version RTOTAL 50 kΩ U version (50k) 3
RH to RL Resistance Tolerance -20 20 % 3
Wiper Resistance RW 70 200 Ω VCC = 3.3V @ 25°C; wiper current = VCC/RTOTAL 3
CH Potentiometer Capacitance CH 10 pF Note 15 3
CL Potentiometer Capacitance CL 10 pF Note 15 3
CW Potentiometer Capacitance CW 25 pF Note 15 3
Leakage on DCP Pins ILkgDCP 0.1 1 µA Voltage at pin from GND to VCC 3
Integral Non-linearity (voltage divider) INL -1 1 LSB Voltage divider mode (Note 2) 3
Differential Non-linearity (voltage divider) DNL -0.5 0.5 LSB Monotonic over all tap positions (Note 2) 3
Zero-scale Error, U option ZSerror 0 1 7 LSB U option (Note 2) 3
Full-scale Error, U option FSerror -7 -1 0 LSB U option (Note 2) 3
DCP to DCP Matching (voltage divider) VMATCH -2 2 LSB Any two DCPs at same tap position and same terminal voltages (Note 2) 3
Ratiometric Temperature Coefficient TCV -4 4 ppm/°C DCP Register set to 80 hex 3
Integral Non-linearity (resistor mode) RINL -1 1 MI DCP register between 20 hex and FF hex; monotonic 3
Differential Non-linearity (resistor mode) RDNL -0.5 0.5 MI Resistor mode 3
Offset, U option Roffset 0 1 7 MI DCP register set to 00 hex, U option 3
DCP to DCP Matching (resistor mode) RMATCH -2 2 MI Any two DCPs at same tap position with same terminal voltages 3
Resistance Temperature Coefficient TCR -45 45 ppm/°C DCP register set between 20 hex and FF hex 3
VCC Supply Current (volatile write/read) ICC1 1 mA fSCL = 400kHz; SDA = Open 4
VCC Supply Current (nonvolatile write) ICC2 3 mA fSCL = 400kHz; SDA = Open 4
VCC Current (standby) ISB 5 µA VCC = +5.5V, I2C interface in standby 4
VCC Current (standby) ISB 2 µA VCC = +3.6V, I2C interface in standby 4
Leakage Current at A0, A1, A2, SDA, SCL, WP ILkgDig -10 10 µA Voltage at pin from GND to VCC 4
DCP Wiper Response Time tDCP 1 µs SCL falling edge of last bit of DCP Data Byte to wiper change (Note 15) 4
Power-on Recall Voltage Vpor 1.8 2.6 V Minimum VCC at which memory recall occurs 4
VCC Ramp Rate VccRamp 0.2 V/ms 4
Power-up Delay tD 3 ms VCC above Vpor, to DCP IVR recall completed and I2C in standby (Note 15) 4
EEPROM Endurance 150000 Cycles 4
EEPROM Retention 50 Years Temperature 75°C 4
Input Buffer LOW Voltage VIL -0.3 V WP, A2, A1, A0, SDA, SCL; maximum printed as 0.3*Vcc 4
SDA Output Buffer LOW Voltage VOL 0 0.4 V Sinking 4mA 4
WP, A2, A1, A0, SDA, SCL Pin Capacitance Cpin 10 pF Note 15 4
SCL Frequency fSCL 400 kHz 4
Pulse Width Suppression Time at SDA and SCL tIN 50 ns Any pulse narrower than the max spec is suppressed (Note 15) 4
SCL Falling Edge to SDA Output Data Valid tAA 900 ns SCL falling edge crossing 30% of VCC until SDA exits 30% to 70% window 4
Time the Bus Must be Free Before Start tBUF 1300 ns SDA crossing 70% of VCC during STOP to START 4
Clock LOW Time tLOW 1300 ns Measured at 30% of VCC crossing 4
Clock HIGH Time tHIGH 600 ns Measured at 70% of VCC crossing 4
START Condition Setup Time tSU:STA 600 ns SCL rising edge to SDA falling edge, both at 70% of VCC 4
START Condition Hold Time tHD:STA 600 ns SDA falling edge at 30% of VCC to SCL falling edge at 70% of VCC 4
Input Data Setup Time tSU:DAT 100 ns SDA exiting 30% to 70% window to SCL rising edge at 30% of VCC 5
Input Data Hold Time tHD:DAT 0 ns SCL rising edge at 70% of VCC to SDA entering 30% to 70% window 5
STOP Condition Setup Time tSU:STO 600 ns SCL rising edge at 70% of VCC to SDA rising edge at 30% of VCC 5
STOP Condition Hold Time tHD:STO 600 ns SDA rising edge to SCL falling edge, both at 70% of VCC 5
Output Data Hold Time tDH 0 ns SCL falling edge at 30% of VCC until SDA enters 30% to 70% window 5
SDA and SCL Rise Time tR 250 ns 30% to 70% of VCC; formula 20 + 0.1*Cb (Note 15) 5
SDA and SCL Fall Time tF 250 ns 70% to 30% of VCC; formula 20 + 0.1*Cb (Note 15) 5
Capacitive Loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip (Note 15) 5
SDA and SCL Bus Pull-up Resistor, off-chip Rpu 1 kΩ Maximum determined by tR and tF (Note 15) 5
Non-volatile Write Cycle Time tWP 12 20 ms Notes 15, 16 5
A2, A1, A0, WP Setup Time tSU:WPA 600 ns Before START condition 5
A2, A1, A0, WP Hold Time tHD:WPA 600 ns After STOP condition 5
Recommended VCC Supply Voltage VCC 2.7 5.5 V 3
Temperature Range (Industrial) TA -40 85 °C 3
Wiper Current of Each DCP IW -3 3 mA 3
Power Rating of Each DCP 5 mW 3
VCC Supply Voltage (absolute) VCC -0.3 6 V 3
Storage Temperature TSTG -65 150 °C 3
Wiper Current (10s) IW -6 6 mA 10s 3
Lead Temperature (soldering, 10s) 300 °C Soldering, 10s 3

CAD (KiCad official)

  • Symbol: X95820UV14IZ-2.7
  • Footprint: Package_SO:TSSOP-14_4.4x5mm_P0.65mm
  • 3D model: TSSOP-14 (KiCad packages3D, STEP)
  • 3D model files: x95820uv14iz-2-7-etched.step / x95820uv14iz-2-7-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); x95820uv14iz-2-7.step / x95820uv14iz-2-7.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (12 pp, sha256 f5958fe4b26f1b84, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF