main
History Download
Ray Publish 0.1.0 d654778

WS339E

GEC · RS-485/RS-422 ICs · QFN-40-EP(6x6)

WS339E from GEC, in a QFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 L1 output Receiver output R1 in RS-232 mode (MODE1,MODE0=01); held at logic 1 in RS-485/422 modes 10 and 11.
2 L2 output Receiver output R2 in RS-232 mode; carries R1 Output in RS-485 half duplex (10) and full duplex (11) modes.
3 L3 input T1 logic input in RS-232, RS-485 half duplex and full duplex modes (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max).
4 L4 input T2 logic input in RS-232 mode (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max).
5 L6 output Receiver output R3 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11.
6 L7 input T3 logic input in RS-232 mode (logic input VIH 2.0V min at VCC=3.3V, VIL 0.8V max).
7 L8 output Receiver output R4 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11.
8 L9 output Receiver output R5 in RS-232 mode; held at logic 1 in RS-485/422 modes 10 and 11.
9 VCC power_in Supply voltage, 3.3V ±5% or 5.0V ±5% (absolute maximum -0.3V to +6.0V).
10 GND power_in Ground.
11 SLEW input SLEW=VCC enables 250kbps slew limiting; SLEW=0V allows 1Mbps (RS-232) or 20Mbps (RS-485/422).
12 DIR1 input Driver/receiver direction control: T1 Enable / R1 Disable in the RS-485 modes as listed per mode.
13 NC unconnected This pin is not used and is not connected internally.
14 MODE0 input Mode select bit 0 (MODE1,MODE0: 00 loopback, 01 RS-232, 10 RS-485 half duplex, 11 RS-485/422 full duplex).
15 MODE1 input Mode select bit 1 (MODE1,MODE0: 00 loopback, 01 RS-232, 10 RS-485 half duplex, 11 RS-485/422 full duplex).
16 NC unconnected This pin is not used and is not connected internally.
17 NC unconnected This pin is not used and is not connected internally.
18 NC unconnected This pin is not used and is not connected internally.
19 ENABLE input ENABLE=VCC for operation, ENABLE=0V for shutdown (shutdown current 10µA max).
20 VCC power_in Supply voltage, 3.3V ±5% or 5.0V ±5%.
21 R9 input R5 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD).
22 R8 input R4 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD).
23 GND power_in Ground.
24 R7 output T3 driver output in RS-232 mode (±5.0V min swing into 3kΩ, ±15kV HBM ESD).
25 R6 input R3 receiver input in RS-232 mode (±15V input range, 5kΩ typical pull-down, ±15kV HBM ESD).
26 GND power_in Ground.
27 R4 bidirectional T2 driver output in RS-232 mode and R1 receiver input B in the RS-485/422 modes (±15kV HBM ESD).
28 R3 bidirectional T1 driver output in RS-232 mode and R2 receiver input A in the RS-485/422 modes (±15kV HBM ESD).
29 GND power_in Ground.
30 R2 bidirectional R2 receiver input in RS-232 mode, R1 input A / T1 output A in the RS-485/422 modes (±15kV HBM ESD).
31 R1 bidirectional R1 receiver input in RS-232 mode, R1 input B / T1 output B in the RS-485/422 modes (±15kV HBM ESD).
32 VCC power_in Supply voltage, 3.3V ±5% or 5.0V ±5%.
33 V- power_in Charge pump negative supply, 0.1uF from ground.
34 C2- passive Charge pump capacitor 2 negative lead.
35 C1- passive Charge pump capacitor 1 negative lead.
36 GND power_in Ground.
37 C1+ passive Charge pump capacitor 1 positive lead, 0.1uF.
38 VCC power_in Supply voltage, 3.3V ±5% or 5.0V ±5%.
39 C2+ passive Charge pump capacitor 2 positive lead, 0.1uF.
40 V+ power_in Charge pump positive supply, 0.1uF to ground.
41 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer GEC
Package QFN-40-EP(6x6)
Category Communication Interface Chip/UART/485/232
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC -0.3 6 V 2
Receiver Input Voltage (from Ground) -18 18 V from Ground 2
Driver Output Voltage (from Ground) -18 18 V from Ground 2
Voltage at TTL Input Pins -0.3 V max printed as VCC + 0.5V 2
Storage Temperature Range -65 150 °C 2
Lead Temperature 300 °C soldering, 10s 2
Power Dissipation 40-pin QFN 500 mW derate 17mW/°C above +70°C 2
Operating Temperature Range -40 85 °C ordering information, WS339EER1 2
Supply voltage tolerance VCC -5 5 % VCC = 3.3V or 5.0V nominal 6
ICC Supply Current (RS-232) ICC 2 8 mA No load, idle inputs 6
ICC Supply Current (RS-485) ICC 2 8 mA No load, idle inputs 6
ICC Vcc Shutdown Current ICC 1 10 µA ENABLE = 0V 6
Logic Input Voltage High VIH 2 V VCC = 3.3V 6
Logic Input Voltage High VIH 2.4 V VCC = 5.0V 6
Logic Input Voltage Low VIL 0.8 V 6
Logic Input Leakage Current Low IIL 1 µA Input Low (VIN = 0V) 6
Logic Input Leakage Current High IIH 1 µA Input High (VIN = VCC), pins 3, 4 and 6 6
Logic Input Pull-down Current IPD 50 µA Input High (VIN = VCC), pins 11,12,14,15,17-19 6
Receiver Output Voltage Low VOL 0.4 V IOUT = 2.5mA 6
Receiver Output Short Circuit Current IOSS -20 60 mA 0 < VO <VCC 6
Receiver Output Leakage Current IOZ -0.1 1 µA 0 < VO < VCC, Receivers disabled 6
Input Voltage Range VIN -15 15 V 7
Input Threshold Low VIL 0.6 1.2 V VCC = 3.3V 7
Input Threshold Low VIL 0.8 1.5 V VCC = 5.0V 7
Input Threshold High VIH 1.5 2 V VCC = 3.3V 7
Input Threshold High VIH 1.8 2.4 V VCC = 5.0V 7
Input Resistance RIN 3 5 7 kΩ -15V <VIN <+15V 7
Output Voltage Swing VO -5 5.5 V Output loaded with 3kΩ to Gnd 7
Output Voltage Swing, no load VO -7 7 V No load output 7
Short Circuit Current ISC -60 60 mA VO = 0V 7
Power Off Impedance ROFF 300 Ω VCC = 0V, VO = ±2V 7
Power Off Impedance ROFF 10 MΩ VCC = 0V, VO = ±2V 7
Receiver Input Resistance RIN 96 kΩ -7V <VIN< +12V 8
Receiver Differential Threshold Voltage VTH -200 -125 -50 mV 8
Receiver Input Current IIN 125 µA VIN = +12V 8
Receiver Input Current IIN -100 µA VIN = -7V 8
Differential Driver Output VOD 2 V RL = 100Ω (RS-422), Figure 5 8
Differential Driver Output VOD 1.5 V RL = 54Ω (RS-485), Figure 5 8
Change In Magnitude of Differential Output Voltage ΔVOD -0.2 0.2 V RL = 54Ω or 100Ω, Figure 5 8
Driver Output Short Circuit Current IOSD -250 250 mA -7V< VO < +12V, Figure 7 8
Driver Output Leakage Current IO 100 µA ENABLE = 0V, or DIR1 = 0V and DIR2 = 0V in full duplex modes, VO = +12V, VCC = 0V or 5.25V 8
Driver Output Leakage Current IO -100 µA ENABLE = 0V, or DIR1 = 0V and DIR2 = 0V in full duplex modes, VO = -7V, VCC = 0V or 5.25V 8
Enable from Shutdown tENABLE 1000 ns 9
Enable to Shutdown tSHUTDOWN 1000 ns 9
Maximum Data Rate (RS-232, SLEW = Vcc) 250 kbps RL = 3kΩ, CL = 1000pF 9
Receiver Propagation Delay (RS-232, 250kbps) tRHL, tRLH 100 ns CL = 150pF, Figure 8 9
Driver Propagation Delay (RS-232, 250kbps) tDHL, tDLH 1400 ns RL = 3kΩ, CL = 2500pF, Figure 9 9
Transition Region Slew Rate (RS-232, 250kbps) tSHL, tSLH 4 30 V/µs VCC = 3.3V, RL = 3kΩ to 7kΩ, CL = 150pF to 2500pF, Figure 9 9
Maximum Data Rate (RS-232, SLEW = 0V) 1 Mbps RL = 3kΩ, CL = 250pF 9
Receiver Propagation Delay (RS-232, 1Mbps) tRHL, tRLH 100 ns CL = 150pF, Figure 8 9
Driver Propagation Delay (RS-232, 1Mbps) tDHL, tDLH 300 ns RL = 3kΩ, CL = 1000pF, Figure 9 9
Transition Region Slew Rate (RS-232, 1Mbps) tSHL, tSLH 15 150 V/µs VCC = 3.3V, RL = 3kΩto 7kΩ, CL = 150pF to 1000pF, Figure 9 9
Maximum Data Rate (RS-485/RS-422, 250kbps) 250 kbps RL = 54Ω, CL = 50pF 10
Receiver Propagation Delay (RS-485/422, 250kbps) tRPHL, tRPLH 150 200 ns CL = 15pF, Figure 10 10
Driver Propagation Delay (RS-485/422, 250kbps) tDPHL, tDPLH 500 1000 ns RL = 54Ω, CL = 50pF, Figure 11 10
Driver Rise and Fall Time tDR, tDF 300 650 1200 ns 10
Receiver Output Enable Time tRZH, tRZL 200 ns CL = 15pF, Figure 12 10
Driver Output Enable Time tDZH, tDZL 1000 ns RL = 500Ω, CL = 50pF, Figure 13 10

CAD (KiCad official)

  • Symbol: WS339E
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: QFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: ws339e-etched.step / ws339e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ws339e.step / ws339e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: GEC datasheet (22 pp, sha256 49d7a31d2d4c982c, retrieved 2026-11-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF