component
WL9005S5-18
Public Made by Adomby adom
WPMtek(Wei Pan Microelectronics) Linear Voltage Regulators (LDO), SOT-23-5L. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownWL9005S5-18
WPMtek(Wei Pan Microelectronics) · Linear Voltage Regulators (LDO) · SOT-23-5L
WL9005S5-18 from WPMtek(Wei Pan Microelectronics), in a SOT-23-5L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input; operating range 2.0V to 7.0V (absolute max 9V), decouple with a ≥1μF ceramic capacitor to GND. |
| 2 | GND | power_in | Ground. |
| 3 | EN | input | Enable control input; high level ≥1.2V enables the output, low level ≤0.4V disables it. |
| 4 | NC | unconnected | No connect. |
| 5 | VOUT | power_out | Regulated output voltage, up to 500mA output current, requires ≥1μF output capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | WPMtek(Wei Pan Microelectronics) |
| Package | SOT-23-5L |
| Category | Power Management |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | 0.985 | 1.015 | x VOUT | VIN = VOUTNOM +1V, IOUT =10mA | 5 | |
| Input Voltage | VIN | 2 | 7 | V | 5 | ||
| Quiescent Current | IQ | 0.3 | 0.5 | µA | VIN >VOUTNOM, VIN=EN, IOUT =0mA | 5 | |
| Shutdown Current | ISHDN | 0 | 0.1 | µA | EN=0 V, VOUT =0 V | 5 | |
| Output Current | IOUT | 500 | mA | VIN = VOUTNOM +1V | 5 | ||
| Dropout Voltage | VDROP | 100 | mV | IOUT =100mA, VOUT =3.3V | 5 | ||
| Dropout Voltage | VDROP | 600 | 750 | mV | IOUT =500mA, VOUT =3.3V | 5 | |
| Line Regulation | ΔVLINE | 0.05 | % / V | IOUT =10mA, VOUTNOM +1.0V ≦ VIN ≦7V | 5 | ||
| Load Regulation | ΔVLOAD | 5 | 20 | mV | VIN = VOUTNOM +1V, 1mA≦ IOUT ≦100mA | 5 | |
| EN High Voltage | VCEH | 1.2 | V | CE High Voltage | 5 | ||
| EN Low Voltage | VCEL | 0.4 | V | CE Low Voltage | 5 | ||
| EN Pin Current | IEN | 0.01 | µA | 5 | |||
| Current Limit | ILIMIT | 650 | mA | 5 | |||
| Short Current | ISHORT | 100 | mA | VOUT = GND | 5 | ||
| Output Noise Voltage | VON | 100 | µVrms | VOUT=3.3V, IOUT =200mA, BW = 100Hz~10KHz | 5 | ||
| Power Supply Rejection Rate | PSRR | 70 | dB | IOUT =100mA, VOUT =3.3V, f=1kHz | 5 | ||
| Power Supply Rejection Rate | PSRR | 65 | dB | IOUT =100mA, VOUT =3.3V, f=10kHz | 5 | ||
| Output Voltage Temperature Coefficient | ΔVOUT/ΔT*VOUT | -100 | 100 | ppm/°C | IOUT =30mA, TA=0~70°C | 5 | |
| Thermal Shutdown Temperature | TSHDN | 160 | °C | 5 | |||
| Thermal Shutdown Hysteresis | ΔTSHD | 20 | °C | 5 | |||
| Supply Input Voltage | VIN | -0.3 | 9 | V | 4 | ||
| EN to GND | VEN | -0.3 | 9 | V | 4 | ||
| Regulated Output Voltage | VOUT | -0.3 | 5 | V | 4 | ||
| Power Dissipation | PD | 500 | mW | SOT23-5L, TA=+25℃ | 4 | ||
| Thermal Resistance (Junction to air) | θJA | 250 | °C /W | SOT23-5L | 4 | ||
| Human Body Model (HBM) | -4000 | 4000 | V | 4 | |||
| Charged Device Mode (CDM) | -2000 | 2000 | V | 4 | |||
| Machine Mode (MM) | 200 | V | 4 | ||||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| Operating Junction Temperature | TJ | 150 | °C | 4 | |||
| Lead Temperature (Soldering 10s) | TLEAD | 260 | °C | 4 | |||
| Operating Ambient Temperature | -40 | 85 | °C | 4 | |||
| Input Voltage | 2 | 7 | V | 4 | |||
| Output Voltage | 0.8 | 5 | V | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | and output capacitors must be back to the WL9005 ground pin using as wide and as short of a copper trace as is practical.Connections using long trace lengths, narrow trace widths, and/or | 10 |
CAD (KiCad official)
- Symbol:
WL9005S5-18 - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5L (KiCad packages3D, STEP)
- 3D model files:
wl9005s5-18-etched.step/wl9005s5-18-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);wl9005s5-18.step/wl9005s5-18.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: WPMtek(Wei Pan Microelectronics) datasheet (11 pp, sha256
2ed7848826dfb0c6, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).