Generated by kicad-footprint-generator · KiCad file format 20260206
UCC3808ADTR-2
Texas Instruments · DC-DC Controllers · SOIC-8
UCC3808ADTR-2 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | COMP is the error amplifier output and PWM comparator input, driven by a true low-output-impedance 2-MHz amplifier that can source and sink current, is internally current limited, and can be pulled to GND to force zero duty cycle. |
| 2 | FB | input | FB is the inverting input to the error amplifier, and FB lead length and stray capacitance should be kept as small as possible for best stability. |
| 3 | CS | input | CS is the input to the PWM, peak current and overcurrent comparators, where the overcurrent comparator is for fault sensing only and exceeding its threshold causes a soft-start cycle while an internal MOSFET discharges the current sense filter capacitor. |
| 4 | RC | output | RC is the oscillator programming pin, set by a resistor to VDD and a capacitor to GND, with timing resistors recommended between 10 kΩ and 200 kΩ, timing capacitors between 100 pF and 1000 pF, and resistors below 10 kΩ to be avoided. |
| 5 | GND | power_in | GND is the reference and power ground for all functions, and a low-impedance board ground plane is highly recommended because of high currents and high-frequency operation. |
| 6 | OUTB | output | OUTB is one of two alternating push-pull high-current gate drive outputs, each rated for 500 mA peak source and 1 A peak sink, switching at half the oscillator frequency with 60 ns to 200 ns dead time between outputs. |
| 7 | OUTA | output | OUTA is one of two alternating push-pull high-current gate drive outputs, each rated for 500 mA peak source and 1 A peak sink, switching at half the oscillator frequency with 60 ns to 200 ns dead time between outputs. |
| 8 | VDD | power_in | VDD is the power input, recommended at 5 V to 14 V for the UCCx808-2 with absolute maximum supply of 15 V (IDD ≤ 10 mA), and should be bypassed to GND with a close ceramic capacitor plus electrolytic, TI recommending 1 µF. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Oscillator frequency | 175 | 194 | 213 | kHz | 6 | ||
| Oscillator amplitude/VDD | 0.44 | 0.5 | 0.56 | V/V | 6 | ||
| Error amplifier input voltage | 1.95 | 2 | 2.05 | V | COMP = 2 V | 6 | |
| Input bias current | -1 | 1 | µA | 6 | |||
| Open loop voltage gain | 60 | 80 | dB | 6 | |||
| COMP sink current | 0.3 | 2.5 | mA | FB = 2.2 V, COMP = 1 V | 6 | ||
| COMP source current | -0.5 | -0.2 | mA | FB = 1.3 V, COMP = 3.5 V | 6 | ||
| Maximum duty cycle | 48 | 49 | 50 | % | Measured at OUTA or OUTB | 6 | |
| Current sense gain | 1.9 | 2.2 | 2.5 | V/V | 6 | ||
| Maximum input signal | 0.45 | 0.5 | 0.55 | V | COMP = 5 V | 6 | |
| Over current threshold | 0.7 | 0.75 | 0.8 | V | 6 | ||
| COMP to CS offset | 0.35 | 0.8 | 1.2 | V | CS = 0 V | 6 | |
| Start threshold (UCCx808A-2) | 4.1 | 4.3 | 4.5 | V | 6 | ||
| Minimum operating voltage after start (UCCx808A-2) | 3.9 | 4.1 | 4.3 | V | 6 | ||
| Hysteresis (UCCx808A-2) | 0.1 | 0.2 | 0.3 | V | 6 | ||
| VDD zener shunt voltage | 13 | 14 | 15 | V | IDD = 10 mA | 6 | |
| CS to output delay | 100 | 200 | ns | COMP = 3.5 V, CS from 0 mV to 600 mV | 6 | ||
| CS sink current | 5 | 10 | mA | CS = 0.5 V, RC = 5.5 V | 6 | ||
| OUT low level | 0.5 | 1 | V | I = 100 mA | 6 | ||
| OUT high level | 0.5 | 1 | V | I = -50 mA, VDD - OUT | 6 | ||
| Rise time | 25 | 60 | ns | CL = 1 nF | 6 | ||
| Fall time | 25 | 60 | ns | CL = 1 nF | 6 | ||
| COMP rise time | 3.5 | 20 | ms | FB = 1.8 V, rise from 0.5 V to 4 V | 6 | ||
| Start-up current | 130 | 260 | µA | VDD < start threshold | 6 | ||
| Operating supply current | 1 | 2 | mA | FB = 0 V, CS = 0 V | 6 | ||
| Supply voltage | 15 | V | IDD ≤ 10 mA | 5 | |||
| Supply current | 20 | mA | 5 | ||||
| OUTA/OUTB source current (peak) | -0.5 | A | peak | 5 | |||
| OUTA/OUTB sink current (peak) | 1 | A | peak | 5 | |||
| Analog inputs (FB, CS) | -0.3 | V | upper limit VDD + 0.3, not to exceed 6 V | 5 | |||
| Power dissipation, D package | 650 | mW | TA = 25°C | 5 | |||
| Junction temperature | TJ | -55 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Supply voltage VDD (UCCx808-2) | VDD | 5 | 14 | V | UCCx808-2 | 5 | |
| Junction temperature (UCC3808-x) | TJ | 0 | 70 | °C | UCC3808-x | 5 | |
| Junction-to-ambient thermal resistance (D, SOIC) | RθJA | 105.4 | °C/W | D (SOIC) package | 5 | ||
| Junction-to-case (top) thermal resistance (D, SOIC) | RθJC(top) | 47.9 | °C/W | D (SOIC) package | 5 | ||
| Junction-to-board thermal resistance (D, SOIC) | RθJB | 46.5 | °C/W | D (SOIC) package | 5 | ||
| Junction-to-top characterization parameter (D, SOIC) | ψJT | 8.7 | °C/W | D (SOIC) package | 5 | ||
| Junction-to-board characterization parameter (D, SOIC) | ψJB | 45.9 | °C/W | D (SOIC) package | 5 | ||
| Minimum duty cycle | 0 | % | COMP = 0 V | 6 | |||
| CS source current | -200 | nA | 6 |
CAD (KiCad official)
- Symbol:
UCC3808ADTR-2 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ucc3808adtr-2-etched.step/ucc3808adtr-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc3808adtr-2.step/ucc3808adtr-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (21 pp, sha256
bca558f31c391728, retrieved 2026-10-29, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).