Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC28C40DGKR

Texas Instruments · DC-DC Converters · VSSOP-8

UCC28C40DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 COMP output Error amplifier output for compensation; internally current-limited to sink 10mA maximum; can command zero duty cycle by forcing to GND.
2 FB input Inverting input to error amplifier for voltage-feedback loop control; internal noninverting reference trimmed to 2.5V ± 1%.
3 CS input Primary-side current sense input to PWM comparator with 3V/V gain; maximum threshold 0.9V to 1.1V (typical 1V); connect to current sensing resistor.
4 RT/CT bidirectional Fixed frequency oscillator set point; connect timing resistor (RRT) to VREF and timing capacitor (CCT) to GND to program switching frequency from 1kHz to 1MHz.
5 GND power_in Ground return for output driver stage and logic level controller section; separate signal and high-current return paths.
6 OUT output On-chip drive stage output for direct MOSFET gate driving; sources and sinks ±1A peak current; actively held low when VDD is below turn-on threshold.
7 VDD power_in Analog controller power supply input with absolute maximum 20V; requires 0.1µF bypass capacitor directly to GND with minimal trace length.
8 VREF power_out 5V reference output (±1% initial accuracy, ±2% over temperature -40°C to 125°C); provides oscillator charging current; requires 0.1µF ceramic bypass to GND.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category Power Management (PMIC)
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VDD VDD 20 V 5
Input current IVDD 30 mA 5
Output drive current (peak) -1 1 A 5
Output energy (capacitive load) EOUT 5 µJ 5
Analog input voltage COMP, CS, FB, RT/CT -0.3 6.3 V 5
Output driver voltage OUT -0.3 20 V 5
Reference voltage VREF 7 V 5
Error amplifier output sink current COMP 10 mA 5
Total power dissipation, DGK package 98.1 °C/W TA = 25°C 5
Lead temperature TLEAD 300 °C soldering, 10 s 5
Operating junction temperature TJ -55 150 °C 5
Storage temperature Tstg -65 150 °C 5
Input voltage VDD (recommended) VDD 18 V 6
Output driver voltage (recommended) VOUT 18 V 6
Maximum continuous voltage from external circuitry on VREF VREF 5.5 V 6
Average output driver current (source and sink) IOUT 200 mA 6
Reference output current (source) IOUT(VREF) 20 mA 6
Operating junction temperature, UCC28C4x TJ -40 125 °C 6
VREF voltage, initial accuracy VREF 4.9 5 5.1 V TJ = 25°C, IOUT = 1mA 7
Total output variation VREF 4.82 5.18 V See (2) 7
Line regulation 0.2 20 mV VVDD = 12V to 18V 7
Load regulation 3 25 mV 1mA to 20mA 7
Temperature stability (VREF) 0.2 0.4 mV/°C See (2) 7
Long term stability (VREF) 5 25 mV 1000 hours, TJ = 125°C, see (2) 7
Output short circuit (source current) IVREF 30 45 55 mA 7
Oscillator initial accuracy fOSC 50.5 53 55 kHz TJ = 25°C, see (3) 7
Oscillator voltage stability 0.2 1 % 12V ≤ VVDD ≤18V 7
Oscillator temperature stability 1 2.5 % TJ(MIN) to TJ(MAX), see (2) 7
Oscillator discharge current 7.7 8.4 9 mA TJ = 25°C, VRT/CT = 2V, see (4) 7
Oscillator discharge current (over temperature) 7.2 8.4 9.5 mA VRT/CT = 2V, see (4) 7
Feedback input voltage, initial accuracy VFB 2.475 2.5 2.525 V VCOMP = 2.5V, TJ = 25°C 7
Feedback input voltage, total variation VFB 2.45 2.5 2.55 V VCOMP = 2.5V 7
Input bias current (source current) IFB 0.1 2 µA VFB = 5V 7
Open-loop voltage gain AVOL 65 90 dB 2V ≤ VOUT ≤ 4V 7
Unity gain bandwidth 1 1.5 MHz See (2) 7
Output sink current (error amplifier) 2 14 mA VFB = 2.7V, VCOMP = 1.1V 7
Output source current (error amplifier) 0.5 1 mA VFB = 2.3V, VCOMP = 5V 7
Low-level COMP voltage VOL 0.1 1.1 V VFB = 2.7V, RCOMP = 15kΩ COMP to VREF 7
Gain (current sense amplifier) ACS 2.85 3 3.15 V/V See (5) (6) 8
Maximum input signal (current sense) VCS 0.9 1 1.1 V VFB < 2.4V 8
Input bias current (current sense) ICS 0.1 2 µA 8
CS to output delay tD 35 70 ns 8
RDS(on) pulldown VOUT(low) 5.5 15 Ω ISINK = 200mA 8
RDS(on) pullup VOUT(high) 10 25 Ω ISOURCE = 200mA 8
Rise time tRISE 25 50 ns TJ = 25°C, COUT = 1nF 8
Fall time tFALL 20 40 ns TJ = 25°C, COUT = 1nF 8
Start threshold (UCCx8C40, UCCx8C41) VDDON 6.5 7 7.5 V 8
Minimum operating voltage (UCCx8C40, UCCx8C41) VDDOFF 6.1 6.6 7.1 V 8
Start-up current ISTART-UP 50 100 µA VVDD = VDDON – 0.5V 8
Operating supply current IVDD 2.3 3 mA VFB = VCS = 0V 8
Junction-to-ambient thermal resistance, DGK RθJA 176.4 °C/W 7
Junction-to-case (top) thermal resistance, DGK RθJC(top) 67.3 °C/W 7
Junction-to-board thermal resistance, DGK RθJB 98.1 °C/W 7
Junction-to-top characterization parameter, DGK ψJT 11.1 °C/W 7
Junction-to-board characterization parameter, DGK ψJB 91.5 °C/W 7

CAD (KiCad official)

  • Symbol: UCC28C40DGKR
  • Footprint: Package_SO:VSSOP-8_2.3x2mm_P0.5mm
  • 3D model: VSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: ucc28c40dgkr-etched.step / ucc28c40dgkr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc28c40dgkr.step / ucc28c40dgkr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (60 pp, sha256 9fa55f996731c56b, retrieved 2026-09-22, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF