← Commit history

Initial commit: component/ucc2897argpr

Ray ·0193a2b886 ·
2 files changed +278
README.mdadded+57
@@ -0,0 +1,57 @@+# UCC2897ARGPR++**Texas Instruments** · AC-DC Controllers And Regulators · QFN-20-EP(4x4)++UCC2897ARGPR from Texas Instruments, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RON | passive | Resistor to GND that programs the charge current and switching frequency of the internal timing capacitor. |+| 2 | ROFF | passive | Resistor to GND that programs the discharge current, switching frequency, and maximum duty cycle. |+| 3 | VREF | power_out | 5V reference voltage output that supplies up to 5 mA and is bypassed to GND with 0.1µF capacitor. |+| 4 | SYNC | bidirectional | Bidirectional synchronization input where external clock must exceed free-running frequency and pulse width must remain less than (1-DMAX)×TSYNC. |+| 5 | GND | power_in | Analog ground reference connected externally to PGND at a single point only. |+| 6 | CS | input | Current sense input for peak current-mode control; cycle-by-cycle current limiting activates at approximately 0.5V threshold; requires RC filter between current-sense resistor and this pin. |+| 7 | RSLOPE | passive | Resistor to GND that programs the slope compensation current amplitude during the main switch on-time. |+| 8 | FB | input | Feedback input that brings error signal from external optocoupler or error amplifier; control voltage range 2.5V to 4.5V with values below 2.5V producing zero duty-cycle output. |+| 9 | SS/SD | input | Soft-start and shutdown input where external capacitor is charged during soft-start and discharged during shutdown. |+| 10 | PGND | power_in | Power ground return for high-current gate driver outputs OUT and AUX; should be connected with minimal impedance and loop area. |+| 11 | AUX | output | Auxiliary P-channel gate driver output providing 2A source and 2A sink current for active-clamp switching with active-low logic. |+| 12 | OUT | output | Main N-channel gate driver output providing 2A source and 2A sink current with active-high logic; 10kΩ pull-down resistor to PGND recommended. |+| 13 | PVDD | power_in | Isolated power supply input for the gate driver circuits separated from VDD internally. |+| 14 | VDD | power_in | Main power supply input requiring 1µF bypass capacitor and energy storage capacitor for proper soft-start operation. |+| 15 | LINEUV | input | Line undervoltage monitor with 1.27V threshold; hysteresis programmed by external resistor divider at LINEUV pin. |+| 16 | LINEOV | input | Line overvoltage monitor with 1.27V threshold; hysteresis programmed by external resistor divider at LINEOV pin. |+| 17 | N/C | unconnected | No internal connection; pin must be left unconnected. |+| 18 | VIN | power_in | Input power rail with internal high-voltage JFET start-up device rated to 120V maximum input voltage. |+| 19 | N/C | unconnected | No internal connection; pin must be left unconnected. |+| 20 | RDEL | passive | Resistor to GND that programs the turn-on delay between AUX and OUT gate driver outputs. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `UCC2897ARGPR`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`+- 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `ucc2897argpr-etched.step` / `ucc2897argpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2897argpr.step` / `ucc2897argpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ucc2897a) (50 pp, sha256 `fb294981fe94b45c`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2897argpr-datasheet.pdf)
page.jsonadded+221
@@ -0,0 +1,221 @@+{+  "slug": "ucc2897argpr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers And Regulators, QFN-20-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "ucc2897argpr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc2897argpr.kicad_sym",+    "ucc2897argpr.kicad_mod",+    "ucc2897argpr.glb",+    "ucc2897argpr.step",+    "ucc2897argpr.lbr",+    "docs/hero.png",+    "docs/ucc2897argpr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC2897ARGPR",+    "manufacturer": "Texas Instruments",+    "package": "QFN-20-EP(4x4)",+    "pin_count": 21,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://www.ti.com/cn/lit/gpn/ucc2897a",+    "parts": {+      "symbol": "ucc2897argpr.kicad_sym",+      "footprint": "ucc2897argpr.kicad_mod",+      "model_3d": "ucc2897argpr-etched.glb",+      "model_3d_plain": "ucc2897argpr.glb",+      "model_3d_step": "ucc2897argpr-etched.step",+      "model_3d_step_plain": "ucc2897argpr.step",+      "lbr": "ucc2897argpr.lbr"+    },+    "distributor_links": {+      "lcsc": "C469850"+    },+    "pins": [+      {+        "number": "1",+        "name": "RON",+        "type": "passive",+        "description": "Resistor to GND that programs the charge current and switching frequency of the internal timing capacitor."+      },+      {+        "number": "2",+        "name": "ROFF",+        "type": "passive",+        "description": "Resistor to GND that programs the discharge current, switching frequency, and maximum duty cycle."+      },+      {+        "number": "3",+        "name": "VREF",+        "type": "power_out",+        "description": "5V reference voltage output that supplies up to 5 mA and is bypassed to GND with 0.1µF capacitor."+      },+      {+        "number": "4",+        "name": "SYNC",+        "type": "bidirectional",+        "description": "Bidirectional synchronization input where external clock must exceed free-running frequency and pulse width must remain less than (1-DMAX)×TSYNC."+      },+      {+        "number": "5",+        "name": "GND",+        "type": "power_in",+        "description": "Analog ground reference connected externally to PGND at a single point only."+      },+      {+        "number": "6",+        "name": "CS",+        "type": "input",+        "description": "Current sense input for peak current-mode control; cycle-by-cycle current limiting activates at approximately 0.5V threshold; requires RC filter between current-sense resistor and this pin."+      },+      {+        "number": "7",+        "name": "RSLOPE",+        "type": "passive",+        "description": "Resistor to GND that programs the slope compensation current amplitude during the main switch on-time."+      },+      {+        "number": "8",+        "name": "FB",+        "type": "input",+        "description": "Feedback input that brings error signal from external optocoupler or error amplifier; control voltage range 2.5V to 4.5V with values below 2.5V producing zero duty-cycle output."+      },+      {+        "number": "9",+        "name": "SS/SD",+        "type": "input",+        "description": "Soft-start and shutdown input where external capacitor is charged during soft-start and discharged during shutdown."+      },+      {+        "number": "10",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground return for high-current gate driver outputs OUT and AUX; should be connected with minimal impedance and loop area."+      },+      {+        "number": "11",+        "name": "AUX",+        "type": "output",+        "description": "Auxiliary P-channel gate driver output providing 2A source and 2A sink current for active-clamp switching with active-low logic."+      },+      {+        "number": "12",+        "name": "OUT",+        "type": "output",+        "description": "Main N-channel gate driver output providing 2A source and 2A sink current with active-high logic; 10kΩ pull-down resistor to PGND recommended."+      },+      {+        "number": "13",+        "name": "PVDD",+        "type": "power_in",+        "description": "Isolated power supply input for the gate driver circuits separated from VDD internally."+      },+      {+        "number": "14",+        "name": "VDD",+        "type": "power_in",+        "description": "Main power supply input requiring 1µF bypass capacitor and energy storage capacitor for proper soft-start operation."+      },+      {+        "number": "15",+        "name": "LINEUV",+        "type": "input",+        "description": "Line undervoltage monitor with 1.27V threshold; hysteresis programmed by external resistor divider at LINEUV pin."+      },+      {+        "number": "16",+        "name": "LINEOV",+        "type": "input",+        "description": "Line overvoltage monitor with 1.27V threshold; hysteresis programmed by external resistor divider at LINEOV pin."+      },+      {+        "number": "17",+        "name": "N/C",+        "type": "unconnected",+        "description": "No internal connection; pin must be left unconnected."+      },+      {+        "number": "18",+        "name": "VIN",+        "type": "power_in",+        "description": "Input power rail with internal high-voltage JFET start-up device rated to 120V maximum input voltage."+      },+      {+        "number": "19",+        "name": "N/C",+        "type": "unconnected",+        "description": "No internal connection; pin must be left unconnected."+      },+      {+        "number": "20",+        "name": "RDEL",+        "type": "passive",+        "description": "Resistor to GND that programs the turn-on delay between AUX and OUT gate driver outputs."+      },+      {+        "number": "21",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 21 added from the footprint"+        ],+        "pages_sent": 50,+        "cost_usd": 0.6129,+        "at": "2026-09-23T01:18:10"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/ucc2897a",+        "pages": 50,+        "sha256": "fb294981fe94b45c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file