← Commit history

Initial commit: component/ucc2895dwtr

Ray ·1aba4f2f60 ·
2 files changed +270
README.mdadded+57
@@ -0,0 +1,57 @@+# UCC2895DWTR++**Texas Instruments** · AC-DC Controllers & Regulators · SOIC-20-300mil++UCC2895DWTR from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | EAN | input | Inverting input to the error amplifier; keep below 3.6 V for proper operation. |+| 2 | EAOUT | bidirectional | Error amplifier output; internally connected to the non-inverting input of the PWM comparator and no-load comparator, internally clamped to soft-start voltage. |+| 3 | RAMP | input | Inverting input of the PWM comparator; receives either the CT waveform in voltage and average current-mode control, or current signal plus slope compensation in peak current-mode control. |+| 4 | REF | power_out | 5-V ±1.2% precision voltage reference supplying up to 5 mA to external loads; bypass with 0.1 μF low ESR low ESL capacitor to ground, do not use more than 4.7 μF total capacitance. |+| 5 | GND | power_in | Chip ground for all circuits except the output stages. |+| 6 | SYNC | bidirectional | Oscillator synchronization pin; bidirectional, can be used as output clock or input to override internal oscillator for synchronization of multiple power supplies. |+| 7 | CT | input | Oscillator timing capacitor for programming the switching frequency; the UCC2895 oscillator charges CT via programmed current, range 100 to 880 pF. |+| 8 | RT | input | Oscillator timing resistor for programming the switching frequency; current programmed by RT, range 40 kΩ to 120 kΩ. |+| 9 | DELAB | input | Delay-programming between complementary-outputs pin; programs the dead time between switching of output A and output B. |+| 10 | DELCD | input | Delay-programming between complementary-outputs pin; programs the dead time between switching of output C and output D. |+| 11 | ADS | input | Adaptive-delay-set pin; sets the ratio between maximum and minimum programmed output delay dead time, must be limited to 0 V to 2.5 V and less than or equal to CS. |+| 12 | CS | input | Current sense input for cycle-by-cycle current limiting and over-current comparator; connects to inverting input of current-sense comparator and non-inverting input of overcurrent comparator. |+| 13 | OUTD | output | Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers. |+| 14 | OUTC | output | Complementary MOS driver output, 100 mA rated; phase shifted with respect to OUTA, drives second half-bridge circuit. |+| 15 | VDD | power_in | Power supply input pin; must be bypassed with minimum 1 μF low ESR low ESL capacitor to ground, addition of 10 μF low ESR low ESL between VDD and PGND recommended, operating range 10 to 16.5 V. |+| 16 | PGND | power_in | Output stage ground connection for high-current output stages; must be electrically tied to GND, board traces must be low impedance. |+| 17 | OUTB | output | Complementary MOS driver output, 100 mA rated; fully complementary with OUTA at nominal 50% duty cycle, intended to drive one half-bridge circuit. |+| 18 | OUTA | output | Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers. |+| 19 | SS/DISB | input | Soft-start and disable pin combining two independent functions; controls soft-start time and chip enable/disable, sources/sinks current set by IRT. |+| 20 | EAP | input | Non-inverting input to the error amplifier; keep below 3.6 V for proper operation. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-20-300mil |+| Category | Power Supply Chip |+| Pins | 20 |++## CAD (KiCad official)++- Symbol: `UCC2895DWTR`+- Footprint: `Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm`+- 3D model: SOIC-20-300mil (KiCad packages3D, STEP)+- 3D model files: `ucc2895dwtr-etched.step` / `ucc2895dwtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2895dwtr.step` / `ucc2895dwtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ucc2895) (61 pp, sha256 `839591a78c6304d9`, retrieved 2026-09-22, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2895dwtr-datasheet.pdf)
page.jsonadded+213
@@ -0,0 +1,213 @@+{+  "slug": "ucc2895dwtr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers & Regulators, SOIC-20-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "ucc2895dwtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc2895dwtr.kicad_sym",+    "ucc2895dwtr.kicad_mod",+    "ucc2895dwtr.glb",+    "ucc2895dwtr.step",+    "ucc2895dwtr.lbr",+    "docs/hero.png",+    "docs/ucc2895dwtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC2895DWTR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-20-300mil",+    "pin_count": 20,+    "category": "Power Supply Chip",+    "subcategory": "AC-DC Controllers & Regulators",+    "datasheet": "https://www.ti.com/cn/lit/gpn/ucc2895",+    "parts": {+      "symbol": "ucc2895dwtr.kicad_sym",+      "footprint": "ucc2895dwtr.kicad_mod",+      "model_3d": "ucc2895dwtr-etched.glb",+      "model_3d_plain": "ucc2895dwtr.glb",+      "model_3d_step": "ucc2895dwtr-etched.step",+      "model_3d_step_plain": "ucc2895dwtr.step",+      "lbr": "ucc2895dwtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C527702"+    },+    "pins": [+      {+        "number": "1",+        "name": "EAN",+        "type": "input",+        "description": "Inverting input to the error amplifier; keep below 3.6 V for proper operation."+      },+      {+        "number": "2",+        "name": "EAOUT",+        "type": "bidirectional",+        "description": "Error amplifier output; internally connected to the non-inverting input of the PWM comparator and no-load comparator, internally clamped to soft-start voltage."+      },+      {+        "number": "3",+        "name": "RAMP",+        "type": "input",+        "description": "Inverting input of the PWM comparator; receives either the CT waveform in voltage and average current-mode control, or current signal plus slope compensation in peak current-mode control."+      },+      {+        "number": "4",+        "name": "REF",+        "type": "power_out",+        "description": "5-V ±1.2% precision voltage reference supplying up to 5 mA to external loads; bypass with 0.1 μF low ESR low ESL capacitor to ground, do not use more than 4.7 μF total capacitance."+      },+      {+        "number": "5",+        "name": "GND",+        "type": "power_in",+        "description": "Chip ground for all circuits except the output stages."+      },+      {+        "number": "6",+        "name": "SYNC",+        "type": "bidirectional",+        "description": "Oscillator synchronization pin; bidirectional, can be used as output clock or input to override internal oscillator for synchronization of multiple power supplies."+      },+      {+        "number": "7",+        "name": "CT",+        "type": "input",+        "description": "Oscillator timing capacitor for programming the switching frequency; the UCC2895 oscillator charges CT via programmed current, range 100 to 880 pF."+      },+      {+        "number": "8",+        "name": "RT",+        "type": "input",+        "description": "Oscillator timing resistor for programming the switching frequency; current programmed by RT, range 40 kΩ to 120 kΩ."+      },+      {+        "number": "9",+        "name": "DELAB",+        "type": "input",+        "description": "Delay-programming between complementary-outputs pin; programs the dead time between switching of output A and output B."+      },+      {+        "number": "10",+        "name": "DELCD",+        "type": "input",+        "description": "Delay-programming between complementary-outputs pin; programs the dead time between switching of output C and output D."+      },+      {+        "number": "11",+        "name": "ADS",+        "type": "input",+        "description": "Adaptive-delay-set pin; sets the ratio between maximum and minimum programmed output delay dead time, must be limited to 0 V to 2.5 V and less than or equal to CS."+      },+      {+        "number": "12",+        "name": "CS",+        "type": "input",+        "description": "Current sense input for cycle-by-cycle current limiting and over-current comparator; connects to inverting input of current-sense comparator and non-inverting input of overcurrent comparator."+      },+      {+        "number": "13",+        "name": "OUTD",+        "type": "output",+        "description": "Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers."+      },+      {+        "number": "14",+        "name": "OUTC",+        "type": "output",+        "description": "Complementary MOS driver output, 100 mA rated; phase shifted with respect to OUTA, drives second half-bridge circuit."+      },+      {+        "number": "15",+        "name": "VDD",+        "type": "power_in",+        "description": "Power supply input pin; must be bypassed with minimum 1 μF low ESR low ESL capacitor to ground, addition of 10 μF low ESR low ESL between VDD and PGND recommended, operating range 10 to 16.5 V."+      },+      {+        "number": "16",+        "name": "PGND",+        "type": "power_in",+        "description": "Output stage ground connection for high-current output stages; must be electrically tied to GND, board traces must be low impedance."+      },+      {+        "number": "17",+        "name": "OUTB",+        "type": "output",+        "description": "Complementary MOS driver output, 100 mA rated; fully complementary with OUTA at nominal 50% duty cycle, intended to drive one half-bridge circuit."+      },+      {+        "number": "18",+        "name": "OUTA",+        "type": "output",+        "description": "Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers."+      },+      {+        "number": "19",+        "name": "SS/DISB",+        "type": "input",+        "description": "Soft-start and disable pin combining two independent functions; controls soft-start time and chip enable/disable, sources/sinks current set by IRT."+      },+      {+        "number": "20",+        "name": "EAP",+        "type": "input",+        "description": "Non-inverting input to the error amplifier; keep below 3.6 V for proper operation."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 61,+        "cost_usd": 0.4156,+        "at": "2026-09-22T07:31:49"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/ucc2895",+        "pages": 61,+        "sha256": "839591a78c6304d9",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 20,+        "described": 20,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file