Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC2895DWTR

Texas Instruments · AC-DC Controllers & Regulators · SOIC-20-300mil

UCC2895DWTR from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EAN input Inverting input to the error amplifier; keep below 3.6 V for proper operation.
2 EAOUT bidirectional Error amplifier output; internally connected to the non-inverting input of the PWM comparator and no-load comparator, internally clamped to soft-start voltage.
3 RAMP input Inverting input of the PWM comparator; receives either the CT waveform in voltage and average current-mode control, or current signal plus slope compensation in peak current-mode control.
4 REF power_out 5-V ±1.2% precision voltage reference supplying up to 5 mA to external loads; bypass with 0.1 μF low ESR low ESL capacitor to ground, do not use more than 4.7 μF total capacitance.
5 GND power_in Chip ground for all circuits except the output stages.
6 SYNC bidirectional Oscillator synchronization pin; bidirectional, can be used as output clock or input to override internal oscillator for synchronization of multiple power supplies.
7 CT input Oscillator timing capacitor for programming the switching frequency; the UCC2895 oscillator charges CT via programmed current, range 100 to 880 pF.
8 RT input Oscillator timing resistor for programming the switching frequency; current programmed by RT, range 40 kΩ to 120 kΩ.
9 DELAB input Delay-programming between complementary-outputs pin; programs the dead time between switching of output A and output B.
10 DELCD input Delay-programming between complementary-outputs pin; programs the dead time between switching of output C and output D.
11 ADS input Adaptive-delay-set pin; sets the ratio between maximum and minimum programmed output delay dead time, must be limited to 0 V to 2.5 V and less than or equal to CS.
12 CS input Current sense input for cycle-by-cycle current limiting and over-current comparator; connects to inverting input of current-sense comparator and non-inverting input of overcurrent comparator.
13 OUTD output Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers.
14 OUTC output Complementary MOS driver output, 100 mA rated; phase shifted with respect to OUTA, drives second half-bridge circuit.
15 VDD power_in Power supply input pin; must be bypassed with minimum 1 μF low ESR low ESL capacitor to ground, addition of 10 μF low ESR low ESL between VDD and PGND recommended, operating range 10 to 16.5 V.
16 PGND power_in Output stage ground connection for high-current output stages; must be electrically tied to GND, board traces must be low impedance.
17 OUTB output Complementary MOS driver output, 100 mA rated; fully complementary with OUTA at nominal 50% duty cycle, intended to drive one half-bridge circuit.
18 OUTA output Complementary MOS driver output, 100 mA rated; one of four outputs optimized to drive FET driver circuits or gate drive transformers.
19 SS/DISB input Soft-start and disable pin combining two independent functions; controls soft-start time and chip enable/disable, sources/sinks current set by IRT.
20 EAP input Non-inverting input to the error amplifier; keep below 3.6 V for proper operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-20-300mil
Category Power Supply Chip
Pins 20

CAD (KiCad official)

  • Symbol: UCC2895DWTR
  • Footprint: Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm
  • 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
  • 3D model files: ucc2895dwtr-etched.step / ucc2895dwtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc2895dwtr.step / ucc2895dwtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (61 pp, sha256 839591a78c6304d9, retrieved 2026-09-22, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF