← Commit history

Initial commit: component/ucc28063adr

Ray ·4ef0152151 ·
2 files changed +241
README.mdadded+52
@@ -0,0 +1,52 @@+# UCC28063ADR++**Texas Instruments** · AC-DC Controllers And Regulators · SOIC-16++UCC28063ADR from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | ZCDB | input | Zero-current detection input for phase B with 1.0V falling threshold and 1.7V rising threshold; input clamped between 0V and 3V. |+| 2 | VSENSE | input | Output voltage sense input regulated to 6.0V reference with 1.25V enable threshold; overvoltage protection thresholds at 6.48V and 6.67V. |+| 3 | TSET | input | Timing set resistor input to ground (66.5kΩ to 400kΩ range) for programming PWM on-time factor and minimum switching period between 25kHz and 50kHz. |+| 4 | PHB | input | Phase B enable/disable control input; below 0.8V threshold disables phase B and phase-fail detection; above 1.0V threshold enables two-phase operation. |+| 5 | COMP | output | Error amplifier transconductance output for voltage-regulation loop compensation with 55µS small-signal gain and 5X large-signal gain; output range 0V to 4.95V. |+| 6 | AGND | power_in | Analog ground connection for signal bypass capacitors, compensation networks, and analog circuit returns; star-connected with PGND to minimize differential voltage. |+| 7 | VINAC | input | Input AC voltage sense from rectified mains voltage divider with brownout threshold at 1.39V and dropout threshold at 0.35V; input range 0V to 6V. |+| 8 | HVSEN | input | High voltage output sense for FailSafe overvoltage protection with 4.87V fault threshold and 4.67V clear threshold; triggers PWMCNTL output when above 2.5V. |+| 9 | PWMCNTL | tri_state | Open-drain PWM control output for downstream converter enable/disable; pulled low when HVSEN exceeds 2.5V with no FailSafe overvoltage or phase-fail condition. |+| 10 | CS | input | Current sense input for cycle-by-cycle overcurrent protection with -200mV threshold in dual-phase mode and -166mV in single-phase mode; 100ns blanking after gate transitions. |+| 11 | GDB | output | Gate drive output for phase B power MOSFET with 1A source and 1.8A sink capability; output voltage clamped at 13.5V nominal. |+| 12 | VCC | power_in | Bias supply voltage input from regulated 14V to 21V source with maximum 20mA input current; bypass with 0.1µF ceramic capacitor located close to pin. |+| 13 | PGND | power_in | Power stage ground connection for gate drive and power supply return; star-connected with AGND to minimize DC and high-frequency voltage differential. |+| 14 | GDA | output | Gate drive output for phase A power MOSFET with 1A source and 1.8A sink capability; output voltage clamped at 13.5V nominal. |+| 15 | VREF | power_in | Voltage reference output providing regulated 6.00V ±0.18V for device internal circuits and external biasing with ±2mA load current capability. |+| 16 | ZCDA | input | Zero-current detection input for phase A with 1.0V falling threshold and 1.7V rising threshold; input clamped between 0V and 3V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `UCC28063ADR`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)+- 3D model files: `ucc28063adr-etched.step` / `ucc28063adr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc28063adr.step` / `ucc28063adr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc28063a.pdf) (46 pp, sha256 `e28a2680b1f9ffa9`, retrieved 2026-09-23, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc28063adr-datasheet.pdf)
page.jsonadded+189
@@ -0,0 +1,189 @@+{+  "slug": "ucc28063adr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers And Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "ucc28063adr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc28063adr.kicad_sym",+    "ucc28063adr.kicad_mod",+    "ucc28063adr.glb",+    "ucc28063adr.step",+    "ucc28063adr.lbr",+    "docs/hero.png",+    "docs/ucc28063adr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC28063ADR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://www.ti.com/lit/ds/symlink/ucc28063a.pdf",+    "parts": {+      "symbol": "ucc28063adr.kicad_sym",+      "footprint": "ucc28063adr.kicad_mod",+      "model_3d": "ucc28063adr-etched.glb",+      "model_3d_plain": "ucc28063adr.glb",+      "model_3d_step": "ucc28063adr-etched.step",+      "model_3d_step_plain": "ucc28063adr.step",+      "lbr": "ucc28063adr.lbr"+    },+    "distributor_links": {+      "lcsc": "C3093798"+    },+    "pins": [+      {+        "number": "1",+        "name": "ZCDB",+        "type": "input",+        "description": "Zero-current detection input for phase B with 1.0V falling threshold and 1.7V rising threshold; input clamped between 0V and 3V."+      },+      {+        "number": "2",+        "name": "VSENSE",+        "type": "input",+        "description": "Output voltage sense input regulated to 6.0V reference with 1.25V enable threshold; overvoltage protection thresholds at 6.48V and 6.67V."+      },+      {+        "number": "3",+        "name": "TSET",+        "type": "input",+        "description": "Timing set resistor input to ground (66.5kΩ to 400kΩ range) for programming PWM on-time factor and minimum switching period between 25kHz and 50kHz."+      },+      {+        "number": "4",+        "name": "PHB",+        "type": "input",+        "description": "Phase B enable/disable control input; below 0.8V threshold disables phase B and phase-fail detection; above 1.0V threshold enables two-phase operation."+      },+      {+        "number": "5",+        "name": "COMP",+        "type": "output",+        "description": "Error amplifier transconductance output for voltage-regulation loop compensation with 55µS small-signal gain and 5X large-signal gain; output range 0V to 4.95V."+      },+      {+        "number": "6",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground connection for signal bypass capacitors, compensation networks, and analog circuit returns; star-connected with PGND to minimize differential voltage."+      },+      {+        "number": "7",+        "name": "VINAC",+        "type": "input",+        "description": "Input AC voltage sense from rectified mains voltage divider with brownout threshold at 1.39V and dropout threshold at 0.35V; input range 0V to 6V."+      },+      {+        "number": "8",+        "name": "HVSEN",+        "type": "input",+        "description": "High voltage output sense for FailSafe overvoltage protection with 4.87V fault threshold and 4.67V clear threshold; triggers PWMCNTL output when above 2.5V."+      },+      {+        "number": "9",+        "name": "PWMCNTL",+        "type": "tri_state",+        "description": "Open-drain PWM control output for downstream converter enable/disable; pulled low when HVSEN exceeds 2.5V with no FailSafe overvoltage or phase-fail condition."+      },+      {+        "number": "10",+        "name": "CS",+        "type": "input",+        "description": "Current sense input for cycle-by-cycle overcurrent protection with -200mV threshold in dual-phase mode and -166mV in single-phase mode; 100ns blanking after gate transitions."+      },+      {+        "number": "11",+        "name": "GDB",+        "type": "output",+        "description": "Gate drive output for phase B power MOSFET with 1A source and 1.8A sink capability; output voltage clamped at 13.5V nominal."+      },+      {+        "number": "12",+        "name": "VCC",+        "type": "power_in",+        "description": "Bias supply voltage input from regulated 14V to 21V source with maximum 20mA input current; bypass with 0.1µF ceramic capacitor located close to pin."+      },+      {+        "number": "13",+        "name": "PGND",+        "type": "power_in",+        "description": "Power stage ground connection for gate drive and power supply return; star-connected with AGND to minimize DC and high-frequency voltage differential."+      },+      {+        "number": "14",+        "name": "GDA",+        "type": "output",+        "description": "Gate drive output for phase A power MOSFET with 1A source and 1.8A sink capability; output voltage clamped at 13.5V nominal."+      },+      {+        "number": "15",+        "name": "VREF",+        "type": "power_in",+        "description": "Voltage reference output providing regulated 6.00V ±0.18V for device internal circuits and external biasing with ±2mA load current capability."+      },+      {+        "number": "16",+        "name": "ZCDA",+        "type": "input",+        "description": "Zero-current detection input for phase A with 1.0V falling threshold and 1.7V rising threshold; input clamped between 0V and 3V."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 46,+        "cost_usd": 0.5394,+        "at": "2026-09-23T04:15:32"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/ucc28063a.pdf",+        "pages": 46,+        "sha256": "e28a2680b1f9ffa9",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file