3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownUCC27624DGNR
Texas Instruments · Gate Drivers · HVSSOP-8
UCC27624DGNR from Texas Instruments, in a HVSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ENA | input | Enable input for Channel A: pulling it LOW disables the OUTA output regardless of INA, pulling it HIGH enables OUTA, and if left floating it defaults to enabled via an internal pullup, so TI recommends connecting it to VDD when unused. |
| 2 | INA | input | Non-inverting input to Channel A, held LOW by an internal pulldown when unbiased or floating, so it should be connected to GND if unused; the recommended input range is -10 V to 26 V. |
| 3 | GND | power_in | Ground: all signals are referenced to this pin, and VDD must be bypassed to it. |
| 4 | INB | input | Non-inverting input to Channel B, held LOW by an internal pulldown when unbiased or floating, so it should be connected to GND if unused; the recommended input range is -10 V to 26 V. |
| 5 | OUTB | output | Channel B gate driver output, rated for DC voltages from -0.3 V to VDD + 0.3 V and for 200 ns pulses from -2 V to VDD + 3 V. |
| 6 | VDD | power_in | Bias supply input with a recommended range of 4.5 V to 26 V (12 V nominal) and an absolute maximum of 30 V, to be bypassed with ceramic capacitors of at least 1 µF and 0.1 µF referenced to GND. |
| 7 | OUTA | output | Channel A gate driver output, rated for DC voltages from -0.3 V to VDD + 0.3 V and for 200 ns pulses from -2 V to VDD + 3 V. |
| 8 | ENB | input | Enable input for Channel B: pulling it LOW disables the OUTB output regardless of INB, pulling it HIGH enables OUTB, and if left floating it defaults to enabled via an internal pullup, so TI recommends connecting it to VDD when unused. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HVSSOP-8 |
| Category | Motor Driver ICs |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, VDD | VDD | -0.3 | 30 | V | 5 | ||
| Output voltage, OUTA, OUTB | -0.3 | V | DC; max printed as VDD +0.3 | 5 | |||
| Output voltage, OUTA, OUTB | -2 | V | 200ns pulse; max printed as VDD +3 | 5 | |||
| Input voltage, INA, INB, ENA, ENB | -10 | 30 | V | 5 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Lead temperature | 300 | °C | Soldering, 10 sec. | 5 | |||
| Lead temperature | 260 | °C | Reflow | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Supply voltage, VDD | VDD | 4.5 | 12 | 26 | V | 5 | |
| Input voltage, INA, INB, ENA, ENB | -10 | 26 | V | 5 | |||
| Output voltage, OUTA, OUTB | 0 | V | max printed as VDD | 5 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| VDD quiescent supply current | IVDDq | 300 | 450 | μA | VINx = 3.3 V, VDD = 3.4 V, ENx = VDD | 6 | |
| VDD static supply current | IVDD | 0.6 | 1 | mA | VINx = 3.3 V, ENx = VDD | 6 | |
| VDD static supply current | IVDD | 0.7 | 1 | mA | VINx = 0 V, ENx = VDD | 6 | |
| VDD operating current | IVDDO | 3.2 | 3.8 | mA | fSW = 1000 kHz, ENx = VDD, VINx = 0 V, 3.3 V PWM | 6 | |
| VDD disable current | IDIS | 0.8 | 1.1 | mA | VINx = 3.3 V, ENx = 0 V | 6 | |
| VDD UVLO rising threshold | VVDD_ON | 3.8 | 4.1 | 4.4 | V | 6 | |
| VDD UVLO falling threshold | VVDD_OFF | 3.5 | 3.8 | 4.1 | V | 6 | |
| Input signal high threshold | VINx_H | 1.8 | 2 | 2.3 | V | Output High, ENx = HIGH | 6 |
| Input signal low threshold | VINx_L | 0.8 | 1 | 1.2 | V | Output Low, ENx = HIGH | 6 |
| Enable signal high threshold | VENx_H | 1.8 | 2 | 2.3 | V | Output High, INx = HIGH | 6 |
| Enable signal low threshold | VENx_L | 0.8 | 1 | 1.2 | V | Output Low, INx = HIGH | 6 |
| Rise time | tRx | 6 | 10 | ns | CLOAD = 1.8 nF, 20% to 80%, Vin = 0 V, 3.3 V | 7 | |
| Fall time | tFx | 10 | 14 | ns | CLOAD = 1.8 nF, 90% to 10%, Vin = 0 V, 3.3 V | 7 | |
| Turn-on propagation delay | tD1x | 17 | 27 | ns | CLOAD = 1.8 nF, VINx_H of the input rise to 10% of output rise, Vin = 0 V, 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°C | 7 | |
| Turn-off propagation delay | tD2x | 17 | 27 | ns | CLOAD = 1.8 nF, VINx_L of the input fall to 90% of output fall, Vin = 0 V, 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°C | 7 | |
| Enable propagation delay | tD3x | 17 | 27 | ns | CLOAD = 1.8 nF, VENx_H of the enable rise to 10% of output rise, Vin = 0 V, 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°C | 7 | |
| Disable propagation delay | tD4x | 17 | 27 | ns | CLOAD = 1.8 nF, VENx_L of the enable fall to 90% of output fall, Vin = 0 V, 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°C | 7 | |
| Delay matching between two channels | tM | 1 | 2 | ns | CLOAD = 1.8 nF, Vin = 0 V, 3.3 V, Fsw = 500 kHz, 50% duty cycle, INA = INB, /tRA, tRB/, /tFA, tFB/ | 7 | |
| Minimum input pulse width | tPWmin | 10 | 15 | ns | CL = 1.8 nF, Vin = 0 V, 3.3 V, Fsw = 500 kHz, Vo > 1.5 V | 7 | |
| Pullup resistance | ROH | 5 | 8.5 | Ω | IOUT = -50 mA | 6 | |
| Pulldown resistance | ROL | 0.6 | 1.1 | Ω | IOUT = 50 mA | 6 | |
| VDD UVLO hysteresis | VVDD_HYS | 0.3 | V | 6 | |||
| Input signal hysteresis | VINx_HYS | 1 | V | 6 | |||
| INx pin pulldown resistor | RINx | 120 | kΩ | INx = 3.3 V | 6 | ||
| Enable signal hysteresis | VENx_HYS | 1 | V | 6 | |||
| EN pin pullup resistance | RENx | 200 | kΩ | ENx = 0 V | 6 | ||
| Peak output source current | ISRC | 5 | A | VDD = 12 V, CVDD = 10 µF, CL = 0.1 µF, f = 1 kHz | 6 | ||
| Peak output sink current | ISNK | -5 | A | VDD = 12 V, CVDD = 10 µF, CL = 0.1 µF, f = 1 kHz | 6 | ||
| Junction-to-ambient thermal resistance (DGN) | RθJA | 48.9 | °C/W | DGN (8-pin) package column | 5 | ||
| Junction-to-case (top) thermal resistance (DGN) | RθJC(top) | 71.8 | °C/W | DGN (8-pin) package column | 5 | ||
| Junction-to-board thermal resistance (DGN) | RθJB | 22.3 | °C/W | DGN (8-pin) package column | 5 | ||
| Junction-to-top characterization parameter (DGN) | ψJT | 2.6 | °C/W | DGN (8-pin) package column | 5 | ||
| Junction-to-board characterization parameter (DGN) | ψJB | 22.3 | °C/W | DGN (8-pin) package column | 5 | ||
| Junction-to-case (bottom) thermal resistance (DGN) | RθJC(bot) | 4.5 | °C/W | DGN (8-pin) package column | 5 |
CAD (KiCad official)
- Symbol:
UCC27624DGNR - Footprint:
Package_SO:HVSSOP-8-1EP_3x3mm_P0.65mm_EP1.57x1.89mm - 3D model: HVSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.0 mm nominal HVSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
ucc27624dgnr-etched.step/ucc27624dgnr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc27624dgnr.step/ucc27624dgnr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
b42590ddafb28a60, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).