UCC21710QDWRQ1

@@ -1,13 +1,180 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "ucc21710qdwrq1",+  "title": "UCC21710QDWRQ1",+  "brief": "Texas Instruments Isolators - Gate Drivers, SOIC-16-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "Texas Instruments Isolators - Gate Drivers, SOIC-16-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "power management (pmic)",     "ucc21710qdwrq1"   ],+  "component": {+    "mpn": "UCC21710QDWRQ1",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-16-300mil",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "Isolators - Gate Drivers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/ucc21710-q1",+    "parts": {+      "symbol": "ucc21710qdwrq1.kicad_sym",+      "footprint": "ucc21710qdwrq1.kicad_mod",+      "model_3d": "ucc21710qdwrq1.glb",+      "model_3d_step": "ucc21710qdwrq1.step",+      "lbr": "ucc21710qdwrq1.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "AIN",+        "type": "input",+        "description": "Isolated analog sensing input (referenced to COM). Parallel a small capacitor to COM for better noise immunity. Recommended operating input range is 0.6 V to 4.5 V referenced to COM. Tie to COM if unused."+      },+      {+        "number": "2",+        "name": "OC",+        "type": "input",+        "description": "Over-current detection input (referenced to COM). Supports lower-threshold detection for SenseFET, DESAT, and shunt-resistor sensing. Tie to COM if unused."+      },+      {+        "number": "3",+        "name": "COM",+        "type": "power_in",+        "description": "Common ground reference on the secondary (gate-drive) side. Connect to the emitter of the IGBT or the source of the SiC-MOSFET being driven."+      },+      {+        "number": "4",+        "name": "OUTH",+        "type": "output",+        "description": "Gate driver output, pull-up (source) path. Delivers up to 10-A peak source current to the power-transistor gate. Swings between VDD and COM."+      },+      {+        "number": "5",+        "name": "VDD",+        "type": "power_in",+        "description": "Positive supply rail for gate-drive voltage (13 V to 33 V VDD-COM recommended, 36 V max VDD-VEE). Bypass with a >10-uF capacitor to COM close to the pin to support specified source peak current."+      },+      {+        "number": "6",+        "name": "OUTL",+        "type": "output",+        "description": "Gate driver output, pull-down (sink) path. Sinks up to 10-A peak current from the power-transistor gate. Swings between VDD and VEE."+      },+      {+        "number": "7",+        "name": "CLMPI",+        "type": "input",+        "description": "Internal Active Miller Clamp input. Connect this pin directly to the gate of the power transistor to enable the internal 4-A Miller clamp when the gate falls below the clamp threshold. Leave floating or tie to VEE if unused."+      },+      {+        "number": "8",+        "name": "VEE",+        "type": "power_in",+        "description": "Negative supply rail for gate-drive voltage (down to -17.5 V VEE-COM abs max). Bypass with a >10-uF capacitor to COM close to the pin to support specified sink peak current."+      },+      {+        "number": "9",+        "name": "GND",+        "type": "power_in",+        "description": "Input-side (primary) power supply and logic ground reference."+      },+      {+        "number": "10",+        "name": "IN+",+        "type": "input",+        "description": "Non-inverting gate driver control (PWM) input, referenced to GND. Logic thresholds 0.7xVCC (VIH) / 0.3xVCC (VIL). Tie to VCC if unused."+      },+      {+        "number": "11",+        "name": "IN-",+        "type": "input",+        "description": "Inverting gate driver control (PWM) input, referenced to GND. Logic thresholds 0.7xVCC (VIH) / 0.3xVCC (VIL). Tie to GND if unused."+      },+      {+        "number": "12",+        "name": "RDY",+        "type": "output",+        "description": "Power-good indicator for VCC-GND and VDD-COM UVLO status. Open-drain output; can be paralleled with other RDY signals. Requires an external pull-up to VCC."+      },+      {+        "number": "13",+        "name": "FLT",+        "type": "output",+        "description": "Active-low fault alarm output asserted upon over-current or short-circuit detection. Open-drain output; can be paralleled with other faults. Requires an external pull-up to VCC."+      },+      {+        "number": "14",+        "name": "RST/EN",+        "type": "input",+        "description": "Dual-purpose reset/enable input. (1) Enable/shutdown of the output side: turning off pulls the FET off via a normal turn-off. (2) Resets a latched DESAT/FLT fault when held low for >1000 ns; FLT is deasserted on the rising edge of RST/EN. In automatic-reset mode, functions purely as EN. Referenced to GND with 0.7xVCC/0.3xVCC logic thresholds."+      },+      {+        "number": "15",+        "name": "VCC",+        "type": "power_in",+        "description": "Input-side (primary) logic power supply, 3.0 V to 5.5 V (6 V abs max). Bypass with a >1-uF capacitor to GND close to the pin."+      },+      {+        "number": "16",+        "name": "APWM",+        "type": "output",+        "description": "Isolated Analog Sensing PWM output on the primary (input) side. Reproduces the isolated analog signal from AIN as a PWM duty cycle referenced to GND. Leave floating if unused. Max output current 20 mA."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/ucc21710-q1",+        "pages": 61,+        "sha256": "a6b1641a6f247e51",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "Texas Instruments",+      "Package": "SOIC-16-300mil",+      "Category": "Power Management (PMIC)",+      "Pins": "16"+    }+  },+  "variants": [+    {+      "mpn": "UCC21710QDWRQ1",+      "kind": "packaging"+    }+  ],+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "ucc21710qdwrq1"+  ],+  "discovery_pitch": "UCC21710QDWRQ1 (Texas Instruments) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +192,5 @@     "docs/ucc21710qdwrq1-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file