main
Ray
Publish 0.1.0
9d8ad52
UCC20520DWR
Texas Instruments · Gate Drive ICs · SOIC-16-300mil
UCC20520DWR from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWM | input | PWM input has a TTL/CMOS compatible input threshold and is pulled low internally if left open. |
| 2 | NC | unconnected | No connection. |
| 3 | VCCI | power_in | Primary-side supply voltage, locally decoupled to GND using a low ESR/ESL capacitor located as close to the device as possible. |
| 4 | GND | power_in | Primary-side ground reference; all signals in the primary side are referenced to this ground. |
| 5 | DISABLE | input | Disables both driver outputs if asserted high and enables them if set low or left open; it is pulled low internally when open, and tying it to ground is recommended for better noise immunity when unused. |
| 6 | DT | input | Programmable dead time pin: tying DT to VCCI gives dead time of about 0 ns, leaving it open gives less than 15 ns, and a 500-Ω to 500-kΩ resistor to GND sets DT (ns) = 10 × RDT (kΩ), with a ceramic capacitor of 2.2 nF or more recommended in parallel with RDT. |
| 7 | NC | unconnected | No connection. |
| 8 | VCCI | power_in | Primary-side supply voltage, internally shorted to pin 3. |
| 9 | VSSB | power_in | Ground for secondary-side driver B and its ground reference for the B channel. |
| 10 | OUTB | output | Output of driver B, connected to the gate of the B channel FET or IGBT; always complementary to OUTA with the programmed dead time. |
| 11 | VDDB | power_in | Secondary-side power for driver B, locally decoupled to VSSB using a low ESR/ESL capacitor located as close to the device as possible. |
| 12 | NC | unconnected | No connection. |
| 13 | NC | unconnected | No connection. |
| 14 | VSSA | power_in | Ground for secondary-side driver A and its ground reference for the A channel. |
| 15 | OUTA | output | Output of driver A, connected to the gate of the A channel FET or IGBT; in phase with the PWM input with a propagation delay. |
| 16 | VDDA | power_in | Secondary-side power for driver A, locally decoupled to VSSA using a low ESR/ESL capacitor located as close to the device as possible. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCCI input supply voltage | VCCI | 3 | 18 | V | 4 | ||
| Driver output bias supply | VDDA, VDDB | 9.2 | 25 | V | 4 | ||
| Ambient temperature | TA | -40 | 125 | °C | 4 | ||
| Junction temperature (recommended) | TJ | -40 | 130 | °C | 4 | ||
| VCCI to GND | -0.3 | 20 | V | 4 | |||
| VDDA-VSSA, VDDB-VSSB | -0.3 | 30 | V | 4 | |||
| OUTA to VSSA, OUTB to VSSB (max VVDDA+0.3, VVDDB+0.3) | -0.3 | V | 4 | ||||
| OUTA to VSSA, OUTB to VSSB (max VVDDA+0.3, VVDDB+0.3) | -2 | V | Transient for 200 ns | 4 | |||
| PWM, DIS, DT to GND (max VVCCI+0.3) | -0.3 | V | 4 | ||||
| PWM transient to GND (max VVCCI+0.3) | -5 | V | Transient for 50 ns | 4 | |||
| VSSA-VSSB, VSSB-VSSA | 1500 | V | 4 | ||||
| Junction temperature (absolute maximum) | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Static common-mode transient immunity (CMTI) | CMTI | 100 | V/ns | Slew rate of GND versus VSSA and VSSB, PWM is tied to GND or VCCI | 9 | ||
| Minimum pulse width | tPWmin | 20 | ns | Output off for less than minimum, COUT = 0 pF | 9 | ||
| Pulse width distortion | tPWD | 6 | ns | /tPDLH, tPDHL/ | 9 | ||
| Propagation delays matching between VOUTA, VOUTB | tDM | 5 | ns | f = 100 kHz | 9 | ||
| Propagation delay INx to OUTx falling edges | tPDHL | 19 | 30 | ns | 9 | ||
| Propagation delay INx to OUTx rising edges | tPDLH | 19 | 30 | ns | 9 | ||
| Output rise time, 20% to 80% | tRISE | 6 | 16 | ns | COUT = 1.8 nF | 9 | |
| Output fall time, 90% to 10% | tFALL | 7 | 12 | ns | COUT = 1.8 nF | 9 | |
| VCCI quiescent current | IVCCI | 1.5 | 2 | mA | DISABLE = VCCI | 8 | |
| VDDA and VDDB quiescent current | IVDDA, IVDDB | 1 | 1.8 | mA | DISABLE = VCCI | 8 | |
| VCCI UVLO rising threshold | VVCCI_ON | 2.55 | 2.7 | 2.85 | V | 8 | |
| VCCI UVLO falling threshold | VVCCI_OFF | 2.35 | 2.5 | 2.65 | V | 8 | |
| VDDA/VDDB UVLO rising threshold | VVDDA_ON, VVDDB_ON | 8 | 8.5 | 9 | V | 8 | |
| VDDA/VDDB UVLO falling threshold | VVDDA_OFF, VVDDB_OFF | 7.5 | 8 | 8.5 | V | 8 | |
| PWM/DISABLE input high voltage | VPWMH, VDISH | 1.6 | 1.8 | 2 | V | 8 | |
| PWM/DISABLE input low voltage | VPWML, VDISL | 0.8 | 1 | 1.2 | V | 8 | |
| Dead time, DT pin left open | 8 | 15 | ns | DT pin is left open, min spec characterized only, tested for outliers | 9 | ||
| Dead time with programming resistor | 160 | 200 | 240 | ns | RDT = 20 kΩ | 9 | |
| Junction-to-ambient thermal resistance | RθJA | 78.1 | °C/W | DW-16 (SOIC) | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 11.1 | °C/W | DW-16 (SOIC) | 5 | ||
| Junction-to-board thermal resistance | RθJB | 48.4 | °C/W | DW-16 (SOIC) | 5 | ||
| Junction-to-top characterization parameter | ψJT | 12.5 | °C/W | DW-16 (SOIC) | 5 | ||
| Junction-to-board characterization parameter | ψJB | 48.4 | °C/W | DW-16 (SOIC) | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Increasing the PCB copper connecting to VDDA, VDDB, VSSA and VSSB pins is recommended (See Figure | 35 |
CAD (KiCad official)
- Symbol:
UCC20520DWR - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ucc20520dwr-etched.step/ucc20520dwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc20520dwr.step/ucc20520dwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
771b4b33c3e4f1a0, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC20520DWR
**Texas Instruments** · Gate Drive ICs · SOIC-16-300mil
UCC20520DWR from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWM | input | PWM input has a TTL/CMOS compatible input threshold and is pulled low internally if left open. |
| 2 | NC | unconnected | No connection. |
| 3 | VCCI | power_in | Primary-side supply voltage, locally decoupled to GND using a low ESR/ESL capacitor located as close to the device as possible. |
| 4 | GND | power_in | Primary-side ground reference; all signals in the primary side are referenced to this ground. |
| 5 | DISABLE | input | Disables both driver outputs if asserted high and enables them if set low or left open; it is pulled low internally when open, and tying it to ground is recommended for better noise immunity when unused. |
| 6 | DT | input | Programmable dead time pin: tying DT to VCCI gives dead time of about 0 ns, leaving it open gives less than 15 ns, and a 500-Ω to 500-kΩ resistor to GND sets DT (ns) = 10 × RDT (kΩ), with a ceramic capacitor of 2.2 nF or more recommended in parallel with RDT. |
| 7 | NC | unconnected | No connection. |
| 8 | VCCI | power_in | Primary-side supply voltage, internally shorted to pin 3. |
| 9 | VSSB | power_in | Ground for secondary-side driver B and its ground reference for the B channel. |
| 10 | OUTB | output | Output of driver B, connected to the gate of the B channel FET or IGBT; always complementary to OUTA with the programmed dead time. |
| 11 | VDDB | power_in | Secondary-side power for driver B, locally decoupled to VSSB using a low ESR/ESL capacitor located as close to the device as possible. |
| 12 | NC | unconnected | No connection. |
| 13 | NC | unconnected | No connection. |
| 14 | VSSA | power_in | Ground for secondary-side driver A and its ground reference for the A channel. |
| 15 | OUTA | output | Output of driver A, connected to the gate of the A channel FET or IGBT; in phase with the PWM input with a propagation delay. |
| 16 | VDDA | power_in | Secondary-side power for driver A, locally decoupled to VSSA using a low ESR/ESL capacitor located as close to the device as possible. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCCI input supply voltage | VCCI | 3 | | 18 | V | | 4 |
| Driver output bias supply | VDDA, VDDB | 9.2 | | 25 | V | | 4 |
| Ambient temperature | TA | -40 | | 125 | °C | | 4 |
| Junction temperature (recommended) | TJ | -40 | | 130 | °C | | 4 |
| VCCI to GND | | -0.3 | | 20 | V | | 4 |
| VDDA-VSSA, VDDB-VSSB | | -0.3 | | 30 | V | | 4 |
| OUTA to VSSA, OUTB to VSSB (max VVDDA+0.3, VVDDB+0.3) | | -0.3 | | | V | | 4 |
| OUTA to VSSA, OUTB to VSSB (max VVDDA+0.3, VVDDB+0.3) | | -2 | | | V | Transient for 200 ns | 4 |
| PWM, DIS, DT to GND (max VVCCI+0.3) | | -0.3 | | | V | | 4 |
| PWM transient to GND (max VVCCI+0.3) | | -5 | | | V | Transient for 50 ns | 4 |
| VSSA-VSSB, VSSB-VSSA | | | | 1500 | V | | 4 |
| Junction temperature (absolute maximum) | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| Static common-mode transient immunity (CMTI) | CMTI | 100 | | | V/ns | Slew rate of GND versus VSSA and VSSB, PWM is tied to GND or VCCI | 9 |
| Minimum pulse width | tPWmin | 20 | | | ns | Output off for less than minimum, COUT = 0 pF | 9 |
| Pulse width distortion | tPWD | | | 6 | ns | /tPDLH, tPDHL/ | 9 |
| Propagation delays matching between VOUTA, VOUTB | tDM | | | 5 | ns | f = 100 kHz | 9 |
| Propagation delay INx to OUTx falling edges | tPDHL | | 19 | 30 | ns | | 9 |
| Propagation delay INx to OUTx rising edges | tPDLH | | 19 | 30 | ns | | 9 |
| Output rise time, 20% to 80% | tRISE | | 6 | 16 | ns | COUT = 1.8 nF | 9 |
| Output fall time, 90% to 10% | tFALL | | 7 | 12 | ns | COUT = 1.8 nF | 9 |
| VCCI quiescent current | IVCCI | | 1.5 | 2 | mA | DISABLE = VCCI | 8 |
| VDDA and VDDB quiescent current | IVDDA, IVDDB | | 1 | 1.8 | mA | DISABLE = VCCI | 8 |
| VCCI UVLO rising threshold | VVCCI_ON | 2.55 | 2.7 | 2.85 | V | | 8 |
| VCCI UVLO falling threshold | VVCCI_OFF | 2.35 | 2.5 | 2.65 | V | | 8 |
| VDDA/VDDB UVLO rising threshold | VVDDA_ON, VVDDB_ON | 8 | 8.5 | 9 | V | | 8 |
| VDDA/VDDB UVLO falling threshold | VVDDA_OFF, VVDDB_OFF | 7.5 | 8 | 8.5 | V | | 8 |
| PWM/DISABLE input high voltage | VPWMH, VDISH | 1.6 | 1.8 | 2 | V | | 8 |
| PWM/DISABLE input low voltage | VPWML, VDISL | 0.8 | 1 | 1.2 | V | | 8 |
| Dead time, DT pin left open | | 8 | | 15 | ns | DT pin is left open, min spec characterized only, tested for outliers | 9 |
| Dead time with programming resistor | | 160 | 200 | 240 | ns | RDT = 20 kΩ | 9 |
| Junction-to-ambient thermal resistance | RθJA | | 78.1 | | °C/W | DW-16 (SOIC) | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 11.1 | | °C/W | DW-16 (SOIC) | 5 |
| Junction-to-board thermal resistance | RθJB | | 48.4 | | °C/W | DW-16 (SOIC) | 5 |
| Junction-to-top characterization parameter | ψJT | | 12.5 | | °C/W | DW-16 (SOIC) | 5 |
| Junction-to-board characterization parameter | ψJB | | 48.4 | | °C/W | DW-16 (SOIC) | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | • Increasing the PCB copper connecting to VDDA, VDDB, VSSA and VSSB pins is recommended (See Figure | 35 |
## CAD (KiCad official)
- Symbol: `UCC20520DWR`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `ucc20520dwr-etched.step` / `ucc20520dwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc20520dwr.step` / `ucc20520dwr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc20520.pdf) (44 pp, sha256 `771b4b33c3e4f1a0`, retrieved 2026-11-12, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc20520dwr-datasheet.pdf)