main
Ray
Publish 0.1.0
d1bcf8c
UC3872MTR
Texas Instruments · Other Lighting Drivers · SSOP-16-150mil
UC3872MTR from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOUT | output | Push-pull N-channel MOSFET drive output complementary to AOUT, high for 50% of the time and switching states at each zero-detect. |
| 2 | AOUT | output | Push-pull N-channel MOSFET drive output complementary to BOUT, high for 50% of the time and switching states at each zero-detect. |
| 3 | VC | power_in | Power supply for the output drivers (absolute max 24V), to be bypassed to ground with a 0.1µF ceramic capacitor. |
| 4 | COMP | output | Error amplifier output with compensation normally connected between COMP and INV; a capacitor to ground limits turn-on current and blanks open lamp detect. |
| 5 | SS | passive | Soft start pin (20µA source) that limits initial turn-on currents and blanks open lamp detect until soft start completes. |
| 6 | N/C | unconnected | No internal connection. |
| 7 | INV | input | Inverting input of the error amplifier and input to open lamp detect; outputs are disabled if below the 1V open lamp detect threshold. |
| 8 | CT | passive | Timing capacitor to GND sets the synchronization frequency range, charged with approximately 200µA to form the ramp for the buck PWM comparator. |
| 9 | ZD | input | Zero-detect input sensing the transformer primary center tap falling to approximately 0.5V threshold, with a typically 10k series resistor to limit input current. |
| 10 | N/C | unconnected | No internal connection. |
| 11 | REF | power_out | 3V reference voltage for internal logic, to be bypassed to ground with a 0.01µF ceramic capacitor. |
| 12 | VCC | power_in | Positive supply for the chip with operating range 4.2V to 24V, to be bypassed to ground with a 0.1µF ceramic capacitor. |
| 13 | ENBL | input | Enable input, device is enabled when high and shut down drawing typically 1µA when pulled low. |
| 14 | COUT | output | Directly drives the buck regulator P-channel MOSFET at twice the AOUT/BOUT frequency, with smooth control up to 100% duty cycle. |
| 15 | PGND | power_in | High current ground connection for the three output drivers. |
| 16 | GND | power_in | Ground reference for the internal reference and all thresholds. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-16-150mil |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (TJ = 25 C) | 2.963 | 3 | 3.037 | V | TJ = 25° C | 2 | |
| Output Voltage (over temperature) | 2.94 | 3 | 3.06 | V | 2 | ||
| Line Regulation | 10 | mV | VCC = 4.75V to 18V | 2 | |||
| Load Regulation | 10 | mV | IO = 0 to −5mA | 2 | |||
| Free Running Frequency | 57 | 68 | 78 | kHz | TJ = 25° C | 2 | |
| Maximum Synchronization Frequency | 160 | 200 | 240 | kHz | TJ = 25° C | 2 | |
| Charge Current | 180 | 200 | 220 | µA | VCT = 1.5V | 2 | |
| Voltage Stability | 2 | % | 2 | ||||
| Temperature Stability | 4 | 8 | % | 2 | |||
| Zero Detect Threshold | 0.46 | 0.5 | 0.56 | V | 2 | ||
| Error Amp Input Voltage | 1.445 | 1.475 | 1.505 | V | VO = 2V | 2 | |
| Error Amp Input Bias Current | -0.4 | -2 | µA | 2 | |||
| Error Amp Open Loop Gain | 65 | 90 | dB | VO = 0.5 to 3V | 2 | ||
| Error Amp Output High | 3.1 | 3.5 | 3.9 | V | VINV = 1.3V | 2 | |
| Error Amp Output Low | 0.1 | 0.2 | V | VINV = 1.7V | 3 | ||
| Error Amp Output Source Current | -350 | -500 | µA | VINV = 1.3V, VO = 2V | 3 | ||
| Error Amp Output Sink Current | 10 | 20 | mA | VINV = 1.7V, VO = 2V | 3 | ||
| Error Amp Unity Gain Bandwidth | 1 | MHz | TJ = 25° C (Note 4) | 3 | |||
| Soft Start Threshold | 2.9 | 3.4 | 3.8 | V | VINV = 0V | 3 | |
| Open Lamp Detect Threshold | 0.6 | 1 | 1.4 | V | VSS = 4.2V | 3 | |
| Soft Start Current | 10 | 20 | 40 | µA | VSS = 2V | 3 | |
| Output Low Level (Outputs A and B, IOUT = 0) | 0.05 | 0.2 | V | IOUT = 0, Outputs A and B | 3 | ||
| Output Low Level (IOUT = 10mA) | 0.1 | 0.4 | V | IOUT = 10mA | 3 | ||
| Output Low Level (IOUT = 100mA) | 1.5 | 2.2 | V | IOUT = 100mA | 3 | ||
| Output High Level (Output C, IOUT = 0) | 13.9 | 14.9 | V | IOUT = 0, Output C | 3 | ||
| Output High Level (Output C, IOUT = -10mA) | 13.5 | 14.3 | V | IOUT = −10mA | 3 | ||
| Output High Level (Output C, IOUT = -100mA) | 12.5 | 13.5 | V | IOUT = −100mA | 3 | ||
| Rise Time | 30 | 80 | ns | TJ = 25° C, Cl = 1nF (Note 4) | 3 | ||
| Fall Time | 30 | 80 | ns | TJ = 25° C, Cl = 1nF (Note 4) | 3 | ||
| Out A and B Duty Cycle | 48 | 49.9 | 50 | % | 3 | ||
| Out C Max Duty Cycle | 100 | % | VINV = 1V | 3 | |||
| Out C Min Duty Cycle | 0 | % | VINV = 2V | 3 | |||
| UVLO Startup Threshold Voltage | 3.7 | 4.2 | 4.5 | V | 3 | ||
| UVLO Hysteresis | 120 | 200 | 280 | mV | 3 | ||
| Enable Input High Threshold | 2 | V | 3 | ||||
| Enable Input Low Threshold | 0.8 | V | 3 | ||||
| Enable Input Current | 150 | 400 | µA | VENBL = 5V | 3 | ||
| VCC Supply Current | 6 | 14 | mA | VCC = 24V | 3 | ||
| VC Supply Current | 5 | 12 | mA | VC = 24V | 3 | ||
| ICC Disabled | 1 | 10 | µA | VCC = 24V, VENBL = 0V | 3 | ||
| Analog Inputs | -0.3 | 10 | V | 2 | |||
| VCC, VC Voltage | 24 | V | 2 | ||||
| ZD Input Current | 10 | mA | High Impedance Source | 2 | |||
| ZD Input Voltage | 24 | V | Low Impedance Source | 2 | |||
| Power Dissipation | 1 | W | TA = 25° C | 2 | |||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Lead Temperature | 300 | °C | 2 | ||||
| VCC Operating Range | VCC | 4.2 | 24 | V | 4 | ||
| Operating Junction Temperature (UC3872) | TJ | 0 | 70 | °C | UC3872 | 2 |
CAD (KiCad official)
- Symbol:
UC3872MTR - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
uc3872mtr-etched.step/uc3872mtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);uc3872mtr.step/uc3872mtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (12 pp, sha256
4f021ba16ffe9cab, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UC3872MTR
**Texas Instruments** · Other Lighting Drivers · SSOP-16-150mil
UC3872MTR from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOUT | output | Push-pull N-channel MOSFET drive output complementary to AOUT, high for 50% of the time and switching states at each zero-detect. |
| 2 | AOUT | output | Push-pull N-channel MOSFET drive output complementary to BOUT, high for 50% of the time and switching states at each zero-detect. |
| 3 | VC | power_in | Power supply for the output drivers (absolute max 24V), to be bypassed to ground with a 0.1µF ceramic capacitor. |
| 4 | COMP | output | Error amplifier output with compensation normally connected between COMP and INV; a capacitor to ground limits turn-on current and blanks open lamp detect. |
| 5 | SS | passive | Soft start pin (20µA source) that limits initial turn-on currents and blanks open lamp detect until soft start completes. |
| 6 | N/C | unconnected | No internal connection. |
| 7 | INV | input | Inverting input of the error amplifier and input to open lamp detect; outputs are disabled if below the 1V open lamp detect threshold. |
| 8 | CT | passive | Timing capacitor to GND sets the synchronization frequency range, charged with approximately 200µA to form the ramp for the buck PWM comparator. |
| 9 | ZD | input | Zero-detect input sensing the transformer primary center tap falling to approximately 0.5V threshold, with a typically 10k series resistor to limit input current. |
| 10 | N/C | unconnected | No internal connection. |
| 11 | REF | power_out | 3V reference voltage for internal logic, to be bypassed to ground with a 0.01µF ceramic capacitor. |
| 12 | VCC | power_in | Positive supply for the chip with operating range 4.2V to 24V, to be bypassed to ground with a 0.1µF ceramic capacitor. |
| 13 | ENBL | input | Enable input, device is enabled when high and shut down drawing typically 1µA when pulled low. |
| 14 | COUT | output | Directly drives the buck regulator P-channel MOSFET at twice the AOUT/BOUT frequency, with smooth control up to 100% duty cycle. |
| 15 | PGND | power_in | High current ground connection for the three output drivers. |
| 16 | GND | power_in | Ground reference for the internal reference and all thresholds. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-16-150mil |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (TJ = 25 C) | | 2.963 | 3 | 3.037 | V | TJ = 25° C | 2 |
| Output Voltage (over temperature) | | 2.94 | 3 | 3.06 | V | | 2 |
| Line Regulation | | | | 10 | mV | VCC = 4.75V to 18V | 2 |
| Load Regulation | | | | 10 | mV | IO = 0 to −5mA | 2 |
| Free Running Frequency | | 57 | 68 | 78 | kHz | TJ = 25° C | 2 |
| Maximum Synchronization Frequency | | 160 | 200 | 240 | kHz | TJ = 25° C | 2 |
| Charge Current | | 180 | 200 | 220 | µA | VCT = 1.5V | 2 |
| Voltage Stability | | | | 2 | % | | 2 |
| Temperature Stability | | | 4 | 8 | % | | 2 |
| Zero Detect Threshold | | 0.46 | 0.5 | 0.56 | V | | 2 |
| Error Amp Input Voltage | | 1.445 | 1.475 | 1.505 | V | VO = 2V | 2 |
| Error Amp Input Bias Current | | | -0.4 | -2 | µA | | 2 |
| Error Amp Open Loop Gain | | | 65 | 90 | dB | VO = 0.5 to 3V | 2 |
| Error Amp Output High | | 3.1 | 3.5 | 3.9 | V | VINV = 1.3V | 2 |
| Error Amp Output Low | | | 0.1 | 0.2 | V | VINV = 1.7V | 3 |
| Error Amp Output Source Current | | | -350 | -500 | µA | VINV = 1.3V, VO = 2V | 3 |
| Error Amp Output Sink Current | | | 10 | 20 | mA | VINV = 1.7V, VO = 2V | 3 |
| Error Amp Unity Gain Bandwidth | | | 1 | | MHz | TJ = 25° C (Note 4) | 3 |
| Soft Start Threshold | | 2.9 | 3.4 | 3.8 | V | VINV = 0V | 3 |
| Open Lamp Detect Threshold | | 0.6 | 1 | 1.4 | V | VSS = 4.2V | 3 |
| Soft Start Current | | 10 | 20 | 40 | µA | VSS = 2V | 3 |
| Output Low Level (Outputs A and B, IOUT = 0) | | | 0.05 | 0.2 | V | IOUT = 0, Outputs A and B | 3 |
| Output Low Level (IOUT = 10mA) | | | 0.1 | 0.4 | V | IOUT = 10mA | 3 |
| Output Low Level (IOUT = 100mA) | | | 1.5 | 2.2 | V | IOUT = 100mA | 3 |
| Output High Level (Output C, IOUT = 0) | | | 13.9 | 14.9 | V | IOUT = 0, Output C | 3 |
| Output High Level (Output C, IOUT = -10mA) | | | 13.5 | 14.3 | V | IOUT = −10mA | 3 |
| Output High Level (Output C, IOUT = -100mA) | | | 12.5 | 13.5 | V | IOUT = −100mA | 3 |
| Rise Time | | | 30 | 80 | ns | TJ = 25° C, Cl = 1nF (Note 4) | 3 |
| Fall Time | | | 30 | 80 | ns | TJ = 25° C, Cl = 1nF (Note 4) | 3 |
| Out A and B Duty Cycle | | 48 | 49.9 | 50 | % | | 3 |
| Out C Max Duty Cycle | | | | 100 | % | VINV = 1V | 3 |
| Out C Min Duty Cycle | | 0 | | | % | VINV = 2V | 3 |
| UVLO Startup Threshold Voltage | | 3.7 | 4.2 | 4.5 | V | | 3 |
| UVLO Hysteresis | | 120 | 200 | 280 | mV | | 3 |
| Enable Input High Threshold | | 2 | | | V | | 3 |
| Enable Input Low Threshold | | | | 0.8 | V | | 3 |
| Enable Input Current | | | 150 | 400 | µA | VENBL = 5V | 3 |
| VCC Supply Current | | | 6 | 14 | mA | VCC = 24V | 3 |
| VC Supply Current | | | 5 | 12 | mA | VC = 24V | 3 |
| ICC Disabled | | | 1 | 10 | µA | VCC = 24V, VENBL = 0V | 3 |
| Analog Inputs | | -0.3 | | 10 | V | | 2 |
| VCC, VC Voltage | | | | 24 | V | | 2 |
| ZD Input Current | | | | 10 | mA | High Impedance Source | 2 |
| ZD Input Voltage | | | | 24 | V | Low Impedance Source | 2 |
| Power Dissipation | | | | 1 | W | TA = 25° C | 2 |
| Storage Temperature | | -65 | | 150 | °C | | 2 |
| Lead Temperature | | | | 300 | °C | | 2 |
| VCC Operating Range | VCC | 4.2 | | 24 | V | | 4 |
| Operating Junction Temperature (UC3872) | TJ | 0 | | 70 | °C | UC3872 | 2 |
## CAD (KiCad official)
- Symbol: `UC3872MTR`
- Footprint: `Package_SO:SSOP-16_3.9x4.9mm_P0.635mm`
- 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files: `uc3872mtr-etched.step` / `uc3872mtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `uc3872mtr.step` / `uc3872mtr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/uc3872.pdf) (12 pp, sha256 `4f021ba16ffe9cab`, retrieved 2026-11-06, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/uc3872mtr-datasheet.pdf)