UC3845BN

{
 "schema": "adom.pads/1",
 "slug": "uc3845bn",
 "footprint": "DIP-8_W7.62mm",
 "generated_from": {
  "footprint": "DIP-8_W7.62mm@sha256:222fb44370968119",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   0.0,
   0.0
  ],
  "corner": "bottom-right",
  "source": "fab-chamfer",
  "derived_from": "DIP-8_W7.62mm@sha256:222fb44370968119"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "thru_hole",
   "shape": "roundrect",
   "at": [
    0.0,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "1",
   "name": "COMP",
   "type": "output",
   "description": "Error amplifier output made available for loop compensation. Typically an RC network is connected between this pin and VFB (pin 2) to shape the control-loop response.",
   "is_pin1": true,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    2.54
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "2",
   "name": "VFB",
   "type": "input",
   "description": "Inverting input of the internal error amplifier. Normally connected to the switching power supply output through a resistor divider; the non-inverting input is internally tied to the 2.5 V reference.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    5.08
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "3",
   "name": "ISENSE",
   "type": "input",
   "description": "Current-sense input. A voltage proportional to the primary/inductor current is applied here; the PWM comparator terminates the output switch conduction when this pin reaches the error-amp-derived threshold (max input signal ~1 V, gain 3 V/V).",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    7.62
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "4",
   "name": "RT/CT",
   "type": "passive",
   "description": "Oscillator timing pin. A resistor RT from this pin to VREF and a capacitor CT from this pin to GROUND set the oscillator frequency and the maximum output duty cycle. Operation up to 500 kHz is possible.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    7.62
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "5",
   "name": "GROUND",
   "type": "power_in",
   "description": "Common control-circuitry and power-stage return. All voltages in the datasheet are referenced to this pin; timing and bypass capacitors must connect close to this pin in a single-point ground.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    5.08
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "6",
   "name": "OUTPUT",
   "type": "output",
   "description": "High-current totem-pole gate-drive output for an external N-channel power MOSFET. Peak source/sink currents up to 1 A; typical rise/fall times ~50 ns into 1 nF.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    2.54
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "7",
   "name": "VCC",
   "type": "power_in",
   "description": "Positive supply of the control IC (labeled Vi in the block diagram/absolute-maximum table). Max 30 V (self-limiting via internal ~36 V zener). UVLO turn-on 8.5 V typ, turn-off 7.9 V typ; operating supply current ~12 mA typ.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "8",
   "name": "VREF",
   "type": "power_out",
   "description": "Buffered 5.0 V reference output (5 V, 50 mA capable). Provides charging current for the timing capacitor CT through the timing resistor RT and can bias external circuitry.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}