main
Ray
Publish 0.1.0
aa1902d
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290
{
"slug": "uc2854bdw",
"version": "0.1.0",
"type": "component",
"description": "Texas Instruments AC-DC Controllers & Regulators, SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
"tags": [
"component",
"power supply chip",
"uc2854bdw",
"factory-2.0.0",
"extractor-text"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"uc2854bdw.kicad_sym",
"uc2854bdw.kicad_mod",
"uc2854bdw.glb",
"uc2854bdw.step",
"uc2854bdw.lbr",
"docs/hero.png",
"docs/uc2854bdw-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"uc2854bdw-hero.glb",
"uc2854bdw-hero.overlay.json",
"uc2854bdw-etched.glb"
],
"component": {
"mpn": "UC2854BDW",
"manufacturer": "Texas Instruments",
"package": "SOIC-16-300mil",
"pin_count": 16,
"category": "Power Supply Chip",
"subcategory": "AC-DC Controllers & Regulators",
"datasheet": "https://www.ti.com/lit/ds/symlink/uc2854b.pdf",
"parts": {
"symbol": "uc2854bdw.kicad_sym",
"footprint": "uc2854bdw.kicad_mod",
"model_3d": "uc2854bdw-hero.glb",
"model_3d_plain": "uc2854bdw-etched.glb",
"model_3d_step": "uc2854bdw-etched.step",
"model_3d_step_plain": "uc2854bdw.step",
"lbr": "uc2854bdw.lbr"
},
"distributor_links": {
"lcsc": "C2878518",
"digikey": "296-2496-5-ND",
"mouser": "595-UC2854BDW"
},
"distributor_check": {
"checked_at": "2026-11-12T08:26:32Z",
"source": "Component Ocean /api/assign-pns",
"digikey": {
"pn": "296-2496-5-ND",
"status": "found"
},
"mouser": {
"pn": "595-UC2854BDW",
"status": "found"
}
},
"pins": [
{
"number": "1",
"name": "GND",
"type": "power_in",
"description": "Ground reference for the device; all bypass and timing capacitors should return to GND with leads as short and direct as possible, and all voltages are measured with respect to GND."
},
{
"number": "2",
"name": "PKLMT",
"type": "input",
"description": "Peak limit input whose threshold is 0.0 V, connected to the negative voltage on the current sense resistor, with a resistor to REF used to offset the negative sense signal up to GND."
},
{
"number": "3",
"name": "CAO",
"type": "output",
"description": "Output of the wide bandwidth current amplifier that commands the PWM to force the correct input current, and it can swing from 0.1 V to 7.5 V."
},
{
"number": "4",
"name": "ISENSE",
"type": "input",
"description": "Inverting input of the switch current amplifier that remains functional down to and below GND, and should not be taken below -0.5 V because it is diode-protected to GND."
},
{
"number": "5",
"name": "MOUT",
"type": "bidirectional",
"description": "Multiplier output and non-inverting current amplifier input that is a high-impedance current node, which should not be taken below -0.5 V and should satisfy IMOUT ≤ 2 × IAC."
},
{
"number": "6",
"name": "IAC",
"type": "input",
"description": "Current input to the analog multiplier proportional to the instantaneous line voltage, where the maximum current at high line should be limited to 250 µA for best performance."
},
{
"number": "7",
"name": "VAO",
"type": "input",
"description": "Voltage amplifier output that forms the third input to the multiplier and is internally clamped to 6.0 V."
},
{
"number": "8",
"name": "VRMS",
"type": "input",
"description": "Input providing the RMS line voltage to the multiplier, with a linear operating range of 0 V to 5.5 V and an external divider that should produce 1.5 V at low line (85 VAC)."
},
{
"number": "9",
"name": "VREF",
"type": "power_out",
"description": "Internal reference output used to set the peak limit point and for various device functions, which must be present for the device to operate."
},
{
"number": "10",
"name": "ENA",
"type": "input",
"description": "Enable input where a nominal voltage above 2.65 V allows operation to begin and the device shuts off below 2.15 V nominal, with the pin internally clamped to approximately 10 V."
},
{
"number": "11",
"name": "VSENSE",
"type": "input",
"description": "Feedback input from the output that feeds the voltage error amplifier, whose output is another input to the multiplier."
},
{
"number": "12",
"name": "RSET",
"type": "input",
"description": "Resistor from RSET to ground that programs the oscillator charging current, and on this device it has no effect on clamping the maximum multiplier output current."
},
{
"number": "13",
"name": "SS",
"type": "input",
"description": "Soft-start pin held at GND while the device is disabled or VCC is too low, which pulls up to over 3 V through an internal 14 µA source when VCC is valid and the device is enabled."
},
{
"number": "14",
"name": "CT",
"type": "input",
"description": "Capacitor from CT to GND that sets the PWM oscillator frequency."
},
{
"number": "15",
"name": "VCC",
"type": "power_in",
"description": "Positive supply rail for the device, with an absolute maximum supply voltage of 22 V."
},
{
"number": "16",
"name": "GTDRV",
"type": "output",
"description": "PWM output as a 1.5-A peak totem-pole MOSFET gate driver, which should use a series gate resistor of at least 5 Ω to prevent gate impedance interaction and excessive overshoot."
}
],
"provenance": {
"extractor": "extract_pins 0.3",
"factory_chain": {
"factory": "2.0.0",
"extractor": "extract_pins 0.3",
"primary_model": "claude-haiku-5-5",
"primary_mode": "text",
"consensus_model": "claude-sonnet-5-5",
"consensus": "agreed",
"guards": "pin_guards 0.1: passed",
"guard_notes": [
"extractor flagged: Pin numbers were taken from the J/N/DW top-view listing on page 6 and cross-checked against the Term; The datasheet labels VCC as input (I) and VREF as output (O); the KiCad types power_in for VCC and p; The datasheet labels VAO and SS as inputs (I) and the 'Voltage amplifier output' wording is ambiguou"
],
"pages_sent": 11,
"cost_usd": 0.0048,
"at": "2026-11-12T08:26:25"
},
"datasheet": {
"url": "https://www.ti.com/lit/ds/symlink/uc2854b.pdf",
"pages": 29,
"sha256": "20dbe220bdb2dfe8",
"source_tier": "mfr"
},
"cad": "KiCad official (CC-BY-SA 4.0)",
"pins": {
"total": 16,
"described": 16,
"cites_pages": true,
"refuses_to_fabricate": true
}
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"models_3d": [
{
"file": "uc2854bdw.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
10.3,
10.3,
2.75
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "159663ceb2b4996b1b89d3111e4a355fc27de3e24d3570f50e5ed9086e0d73af",
"checked": "2026-11-12",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "uc2854bdw-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
10.3,
10.3,
2.75
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "5882fe18c26f6205abae6fbd0b48a06a058eaa794b53308c1002d7241cefa002",
"checked": "2026-11-12",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
],
"package_dims": {
"package_code": "DW0016A",
"source_page": 23,
"D": {
"nom_mm": 10.3,
"range_mm": [
10.1,
10.5
]
},
"E1": {
"nom_mm": 7.5,
"range_mm": [
7.4,
7.6
]
},
"E": {
"nom_mm": 10.3,
"range_mm": [
9.97,
10.63
]
},
"e": {
"nom_mm": 1.27,
"range_mm": [
null,
null
]
},
"A": {
"nom_mm": 2.65,
"range_mm": [
null,
2.65
]
},
"source": "datasheet package drawing, every number found on its page (extract_pins --task dims)",
"model_check": {
"file": "uc2854bdw.step",
"verdict": "PASS",
"reasons": [
"height and body within the datasheet's package drawing"
],
"by": "factory/package_fit.py"
}
}
}
}